Equipment For Sale

Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

6"x42" wide overall, includes infeed and outfeed rollers, working condition

Schurman Gang Saw Infeed Positioner

Schurman 6TA48 Combination Edger SN: 2121 3 phase 480 volt (2) 200 HP motors

9' Sherman Transfer Deck, 16' wide with H78A roof top chain, gear reduction drive, 16' jump up roll case, (9) 24"x6" rolls

Infeed to 10" Schurman gang edger; this item belongs with stock #727, which is also listed in our equipment for sale. - Call Jeff for more info at 574-370-5050

Shurman 6SBA 42 S/N 1171 Gang Edger with 150Hp Motor

10D G60 thin kerf double arbor schurman gang edger; this item belongs with stock #729, which is also listed in our equipment for sale. Call Jeff at 574-370-5050 for more info.

SCHURMAN SINGLE ARBOR GANG SAW 6" x 60"

One (1) Used Schurman Top Arbor 2-Saw 4” X 24” Recovery Edger complete with 12’ infeed table, outfeed picker belt, and TEFC motors. Arbor drive is 100HP. Feed rolls are 2-speed 7½HP. Currently equipped as a fixed spacing (4” nominal) machine. Can be restored to 2-shifting saw configuration. No setworks now included. Appears in good condition. See photos of Schurman Top Arbor 2-Saw 4” X 24” Recovery Edger on our web site. Inventory No. 10202P. Located at our Portland, Oregon facility. Click on link for photos. http://www.machinerysales.com/equipment.php?item=10202

Schutte Pallet Hog - Model 56-35 heavy-duty horizontal hog. Features 50"w x 7-1/2"h horizontal feed opening with top and bottom powered rolls; 50 2-way, reversible swinging hammers with hardsurfaced tips 250 HP direct drive electric motor; 3/4" thick screen with 1-3/8" diameter holes; Rear discharge. Electrical cabinets included. Hammers are approximately 1-3/4" x 5" x 8". Serial #0506071.

Schutte model 280.100 Hammer Mill Includes: 125 HP Motor - 480v Includes: (3) Screens: Approx 1", 3/4", 3/8" (to be confirmed) Includes: Stand

Schutte Hammer Mill #40 S/N 111375-R

Grinder. This machine is a Shutte grinder. With Webster vibratory infeed. Item #C625

Schutte Hammer Mill Horizontal Infeed HZF40 w/100HP Electric Motor and Attached Blower

Schutte Hammer Mill 40-HZF with 100HP Electric Motor. No. 172 Attached Blower.

Schutte Swing Hammer Grinder

Schutte Pallet Hog - Model 56-35 heavy duty horizontal hog.   Features 50 inch wide horizontal feed  opening with top and bottom powered rolls; 50  2-way, reversible swinging hammers with hardsurfaced tips ; 250 HP direct drive electric motor; 3/4" thick screen with 1-3/8" diameter holes;    Rear discharge.   Electrical cabinets included.   Hammers are approximately 1-3/4" x 5" x 8".    Serial #0506071.

SCHUTTE BUFFALO - Model WA16L, ... HammermillModel# WA16L, 3500 RPM, with filtration system and multiple grates for destruction sizes. -- It also includes Electrical panel. -- This system is apart and palletized. All you have to do is pick it up and transport it to you. -- System was in perfect working order when it was taken apart and palletized for transport. -- The system is perfect for the destruction of computer hard drives and different types of media.

SCMI SANDYA S300 RCS 110 DUAL HEAD WIDE BELT SANDER43" Width capacity, (1) contact roll & (1) combination head with contact roll & segmented platen.Head Configuration1st Head : 5-1/2" diameter steel calibrating contact roll2nd Head : 5-1/2" diameter rubber covered contact roll and adjustable segmented finishing platen.Specifications -- 0" to 6.69" thickness capacity via motorized bed adjustment with auto set up device. -- Abrasive Belt dimensions 43" X 75" -- Rubber coated pressing rollers before and after working unit -- 1 HP Inverter variable speed feed unit. -- Feed speeds 10 - 60 FPMEquipped with and Features -- Y-Delta two-stage reduced voltage starter on 18 HP main motor -- 2 Roller Infeed and Outfeed table extensions -- Automatic Electronic Table Positioning Device -- Adjustable sanding drum and pad position for micro precision adjustment -- Electronic digital thickness readout of work table position -- Powered table lifting by means of (4) heavy duty motor and lifting columns double fastened at both top and bottom of the lifting columns to provide exceptional table stability -- Electronic tracking of abrasive belt -- Automatic feed mat tracking -- Pneumatic belt tensioning with center fulcrum to compensate for tapering of abrasive belt