Equipment For Sale

--In Auction--Starting bid: $100-- Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

SCHURMAN SINGLE ARBOR GANG SAW 6" x 60"

Shurman 6SBA 42 S/N 1171 Gang Edger with 150Hp Motor

One (1) Used Schurman Top Arbor 2-Saw 4” X 24” Recovery Edger complete with 12’ infeed table, outfeed picker belt, and TEFC motors. Arbor drive is 100HP. Feed rolls are 2-speed 7½HP. Currently equipped as a fixed spacing (4” nominal) machine. Can be restored to 2-shifting saw configuration. No setworks now included. Appears in good condition. See photos of Schurman Top Arbor 2-Saw 4” X 24” Recovery Edger on our web site. Inventory No. 10202P. Located at our Portland, Oregon facility. Click on link for photos. http://www.machinerysales.com/equipment.php?item=10202

Schurman 6TA48 Combination Edger SN: 2121 3 phase 480 volt (2) 200 HP motors

Infeed to 10" Schurman gang edger; this item belongs with stock #727, which is also listed in our equipment for sale. - Call Jeff for more info at 574-370-5050

10D G60 thin kerf double arbor schurman gang edger; this item belongs with stock #729, which is also listed in our equipment for sale. Call Jeff at 574-370-5050 for more info.

Schurman Gang Saw Infeed Positioner

6"x42" wide overall, includes infeed and outfeed rollers, working condition

9' Sherman Transfer Deck, 16' wide with H78A roof top chain, gear reduction drive, 16' jump up roll case, (9) 24"x6" rolls

Schutte Pallet Hog - Model 56-35 heavy-duty horizontal hog. Features 50"w x 7-1/2"h horizontal feed opening with top and bottom powered rolls; 50 2-way, reversible swinging hammers with hardsurfaced tips 250 HP direct drive electric motor; 3/4" thick screen with 1-3/8" diameter holes; Rear discharge. Electrical cabinets included. Hammers are approximately 1-3/4" x 5" x 8". Serial #0506071.

Schutte model 280.100 Hammer Mill Includes: 125 HP Motor - 480v Includes: (3) Screens: Approx 1", 3/4", 3/8" (to be confirmed) Includes: Stand

SCHUTTE BUFFALO - Model WA16L, ... HammermillModel# WA16L, 3500 RPM, with filtration system and multiple grates for destruction sizes. -- It also includes Electrical panel. -- This system is apart and palletized. All you have to do is pick it up and transport it to you. -- System was in perfect working order when it was taken apart and palletized for transport. -- The system is perfect for the destruction of computer hard drives and different types of media.

Grinder. This machine is a Shutte grinder. With Webster vibratory infeed. Item #C625

Schutte Hammer Mill Horizontal Infeed HZF40 w/100HP Electric Motor and Attached Blower

Schutte Pallet Hog - Model 56-35 heavy duty horizontal hog.   Features 50 inch wide horizontal feed  opening with top and bottom powered rolls; 50  2-way, reversible swinging hammers with hardsurfaced tips ; 250 HP direct drive electric motor; 3/4" thick screen with 1-3/8" diameter holes;    Rear discharge.   Electrical cabinets included.   Hammers are approximately 1-3/4" x 5" x 8".    Serial #0506071.

Schutte Hammer Mill #40 S/N 111375-R

Schutte Hammer Mill 40-HZF with 100HP Electric Motor. No. 172 Attached Blower.

Schutte Swing Hammer Grinder

SCM OLIMPIC K360 EDGEBANDER (W/PRE-MILLING):Specifications -- Edge Capacity: 0.3 - 3 mm (0.012 - 0.118"); for coiled edges: 0.3 - 6 mm strips with: 6 x 60 mm kit included; dia. coil holder plate: 780 mm (31"). -- Panel Capacity. Min. width: 90 mm; min. length: 140 mm (3-1/2" & 5-1/2"); panel thickness min./max.: 8 - 50 mm (3/8" - 2") & max. 60 mm (2.4") with 6 x 60 mm kit included.Equipped with: -- Adjustable Infeed Fence: Manually preset with digital indicator; pneumatic in/out positioning. -- Premilling Station - "RT-VP": Spindles: (2) x 2.0 HP - 19,000 RPM; (1) PLC controlled jump action; diamond cutterheads. -- Automatic Strip & Coil Feed Magazine: For straight edges; 3 mm guillotine for coils. -- Gluing Station for EVA (Hot Melt) with: Teflon-coated glue tank; quick disconnect to change glue tanks fast if needed; Heat-up time approx. 10 Min. Includes 1.5 kG glue pot instead of standard. -- Pressure Section: Manual digital positioning, (3) pressure rollers: 1st Larger; Teflon Coated and powered. Workstations -- End Trimming Station - "K2". Front & rear: (2) x 1/2 HP (included extra); 12,000 RPM Motors mounted on THK guides; swivels 0° - 15°; rapid setup between straight & angled cutting with the automatic swivel cylinder.Automatic positioning for (3) cutting modes: Straight, chamfered, and radius of thick edges. -- Top & Bottom Trimming Unit - "R-K". Remote (via control panel) pneumatic positioning for (3) settings: Flush/bevel/radius trimming; (2) x 0.7 HP - 12,000 RPM motors with precision digital indicators for quick setup. -- Top & Bottom Profile Scraping Unit. Manual preset with: Digital indicators; large dia. copy wheels for max. accuracy; pneumatic in/out positioning. -- Buffing Unit - "SP-V": Top/bottom; (2) x 1/4 HP - 2,800 RPM Motors; tilting up to 12°; cleaning & polishing of edges.Controls -- ORION - "1" Plus: Controller. Fixed at infeed of machine; soft keys; graphics; 4" LCD display panel.Handles most machine setup functions & workstations; machine automation by PLC function; encoder positioned in the panel feed track pinion; diagnostics for a quick solution to many errors; process statistics data: Number of pieces/edges and track feeding.Features & Complete with: -- Feed speed: 36 FPM Fixed; (1) x 2.0 HP feed drive motor; 200 Hz frequency inverter for all trimming units; manual adjustable holddown pressure beam; full sound enclosure cover; outboard panel support. -- Overall dimensions: 3,600 mm (142") x 900 mm (36") x 1,600 mm (63"); approx. weight: 997 kG (2,200 Lbs). -- UL/CSA approved version.