Equipment For Sale

This Newman HP-688 press is powered by a 10 HP hydraulic pump. It consists of two 30? X 74? bays. Each bay has (3) individual 24? X 30? platens. Each platen is 15/16? thick and it’s back structure is webbed every 5-1/2? X 7-1/2?. Each platen is driven by a 5? hydraulic cylinder with it’s own control. The max daylight opening is 48? while the minimum is 37?. On the bottom you will find pop up bed rolls. Over all the press is in excellent condition, is extremely heavily built. This fully functional machine has been fully cleaned, checked, and is ready to work

Newman 5 Saw KM16 Trimmer. Main Shaft re-bushed 2 years ago. Located in SC. #C978

Newman Knife Sharpener

Newman KM16 5 Saw Trimmer. 16' Max Length. Located in Alabama. #C982

Newman KM-16 | Comes with 2 package infeed decks | 1-unassembled and needs tlc |1-10' wide in operable condition.

Newman KM16 Trim Saw Has been 90% rebuilt with new main shaft, bearings, chains, aluminum slides, sprockets etc. Has electrical box with starters 10 hp motors Off bearing and waste conveyors Comes with 21’ incline waste conveyor

NEWMAN 990 Planer-Matcher 16 knife heads 6-roll fabricated frame 12" width capacity 6" thickness capacity Side head servo positioner Top head servo positioner Factory (Newman) conversion electric feed roll drive with 6 individual drive motors and direct coupled PlanetGear speed reducers on each feed roll. (25 HP) 150 HP Top Head 100 HP Bottom Head 75 HP Left Side Head 50 HP Right Side Head Several spare side heads Spare 75 HP left side head motor All standard TEFC motors All air and hydraulic valves are new in 2019 Also includes 2019 Newman pineapple feed table with electric drives 3 each 20 HP direct drives on top feed rolls with PlanetGear Reducers 1 ea 25 HP direct drives on top feed rolls with PlanetGear Reducer Newman bridge with direct drive and PlanetGear Reducer 2019 aux hydraulic pump unit for press roll positioning & pressure bar Omega moisture detection & marking equipment 5-strand deck 16' wide x 11' long with hook stops, with tipple on tail end, with additional short 55-strand integrated into the feed table.

NEWMAN/Cameron - KF-24: Dip Chain Gang Rip Saw with CAMERON "34H-M1" Infeed SystemSpecifications -- Saw Arbor: 24" Arbor cap.; 14" max. dia. tooling; 4" max. motorized thickness adjustment;22" min. length for glue joint accuracy; 6" throat. -- 2-13/16" Dia. arbor; 24-1/2" capacity saw sleeve arranged for 3-1/8" dia. bore saw blades; saw blade options: 10" - 14" Dia.; spacers: 4-5/8" dia. includes: (1) Saw sleeve and spacers. -- 75 HP - 3,600 RPM TEFC Direct drive motor; arbor with: Disc brake & load meter; arbor lockout on the access door. Feed & Chain: -- 5 HP Variable feed speed: 20 to 100 FPM with: Jam arbor protection. Dip bed carried on: 5" Pitch hardened Double-V chain; hardened dip cams; extruded structural aluminum feed bed slats with: Replaceable steel-backed rubber insert strips; automatic chain oiler with low level shutoff. -- (2) 4" Dia. air loaded overhead pressure rolls; spring-loaded overhead bed plate; pressure rolls & bed plate unit with motorized adjustment; slide type infeed guide with: Handle block; either side of the guide can be used for a stock engraver. -- Anti-kickback finger system with: (1) Lower & (2) upper on infeed; (1) upper kickback on outfeed. Equipped with & Features: Upper outfeed main dust hood: 7-7/8" Dia. 2,150 CFM Infeed dust hood 4-7/8 dia. (855 CFM). (1) Spare sleeve; (2) setup fixtures; generous array of spacers (see photos).

20’ lengths | All components inspected and replaced as required | Entire shaft was removed, inspected, polished and re-installed. | New roller chain | New lugs | New UHM slides

Newman Whitney RH Drop Saw Trimmer

Newman S-382 Double Head Planer (Straight Knives) w/Hydraulics & Controls S/N 15292

Newman G200 Knife Grinder

NEWMAN G-200 Knife Grinder - grinds 4 chipper knives up to 20" long or 8 planer knives.   Features automatic feed and flood coolant.

Newman KM-16 Overhead 5 Head Trim Saw

Newman KNO 24 lumber trimmer, (9) station drop saw, will pass rail tie’s, includes waste conveyor & infeed this saw is out and ready to load in your truck. Ref #188

Newman K 2S Double End Trimmer

Newnes 3HP HPU

Specially designed haunching machine for beaded face frames, picture frames and decorative cabinetry. This machine uses a specially designed 2-piece carbide insert adjustable cutter. -- The work piece is placed on the table and against the fence and the cutter travels in a vertical motion to achieve the precision cut. -- Any size cut width is attainable by adjusting the width of the cutter and indexing from the fence stops. -- TECHNICAL SPECIFICATIONS -- Motors: 1 @ 1.1 KW (1.5 HP), Voltage: 220/440V/3/60hz, RPM: 6,000 RPM @ 60 hz, Air: 6 Bar, -- TOOLING: Insert Carbide: Milling head 140 mm (5.5"), Height min: no min., width 1/6" (4.2 mm). Max Profile: Height 3.5" (88.9 mm), width no max. -- Machine Dimensions: L x W x H - 40" x 30" x 35". Machine Weight: 675 lbs. -- AVAILABLE OPTIONS (Call for Pricing): Tooling carbide insert head, additional set of inserts, additional flip stops, foot pedal control, left & right digital fence.

Multiple Spindles (2) 2HP motors 208/230/460

Nicholson A5A 27" Dual Highspeed Automatic Ring Debarker w/Controls S/N 6326, 3Hp Hyd Power Pack, 3 Phase, Automatic Lubricating Systemw/(2) 250 Gal Reservoir w/Lubricating Oil