Equipment For Sale

BRANDT KDF 780 2C EDGEBANDER WITH PRE-MILL AND CORNER ROUNDINGBasic Specifications: -- 0.4 - 15 mm (5/8") Edge cap., panel thickness 5/16" - 2-3/8", min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; line control (NO limit switches) for workstation function.Features: -- Pressure Beam with motorized height adjustment for all work stations includes digital height indicator. -- PC-20 Program Control; with 12" Industrial PC flat screen 256 MB RAM, 1 GB Flash Card, with USB Port & remote diagnostic link. -- Signal infeed light to ensure proper spacing between panels. -- Quick heat-up glue system,(approx. 10 minutes) w/hopper feeder & w/glue tank for maintenance & quick glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 minutes or more. -- The glue applicator roller is also reversable and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table 800 mm diameter to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (3) secondary rollers "pneumatically controlled" pressure section. -- Variable Feed speed 36 - 65 FPM (3 HP feed motor) -- Corner rounding station operates at 16 m/Min (52 FPM).Workstations: -- (2) Motor Pre-milling Unit; (2) 3 HP motors (12,000 RPM) to clean-up potential chipped edges. -- End Trimming: (2) 1/2 HP - 12,000 RPM motors) chamfers 0° - 15° via programmable controller. -- Pre-Trimming: Top & bottom flush/bevel trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Fine-Trimming: Top & bottom flush/bevel/radius trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Corner Rounding (Contour) Trimming Unit: (2) motor 1/2 HP - 12,000 RPM each motor for corner rounding for front & trailing corners on the fly. -- Profile Scraping Unit: Top & bottom for 1 - 3 mm PVC radius, depending on tooling. -- Open Space: For the ability to add a top & bottom flat/glue scraper. -- Buffing Station: Top & bottom oscillating buffing (0.25 HP - 2,800 motors). -- Hot Air Unit: (1) Hot air blower to reactivate top/bottom edge after profile scraping and buffing, restoring original edge color luster.Complete With: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts. -- End trim, flush trim & fine trim and corner rounding stations have HF motors with electronic brakes. -- Original Factory machine documentation.

BRANDT PROFILINE KDF 970 2C HD EDGEBANDER WITH PRE MILL & CORNER ROUNDINGSpecifications: -- Edgebanding thickness 0.4 - 20 mm (0.02" - 0.79"), Including 3 mm (0.12") PVC banding. -- Panel thickness 8 - 60 mm (0.31" - 2.38"), Min. panel width 65 mm (2.56"), Min. panel length 160 mm (6.30"). -- Variable feed speeds 36 - 65 FPM (11 - 20 MPM), Max. feed speed using corner rounding units or applying solid wood 52 FPM (16 MPM). -- Working height 900 mm (35.43").Equipped with: -- Pre-milling unit, with (2) 3 kW (4 HP) - 11,580 RPM Vertical milling/jointing heads with FS Whisper Heads, Electro-pneumatic jump control, Head counter-rotation, & SIKO digital units for vertical & horizontal adjustments. -- 32-1/2" Dia. Coil table. -- Motorized infeed fence. -- Extended magazine for strips & coiled material. -- Reinforced guillotine for coiled edgebanding material, 0.4 - 3.5 mm (0.2" - 0.14") Thickness & 8 - 55 mm (0.31" - 2.17") Height. -- "Quick-Melt" Hot melt glue unit, with Heat-up time: Approx. 12 min., Pre-melt hopper feed, Quick-change hopper & tank for color changes, Reversible glue applicator roller rotation, Retractable glue roller, Infrared heating unit positioned between glue roller & pressure section to improve edge quality, and Pneumatic positioning & Locking. -- Programmable pressure section, with (1) Large driven & (4) Small pneumatically-controlled idler rolls and SIKO Digital units for adjustments. "POWER CONTROL PC 20+" Control, with 600 MHz, 256 MB RAM, USB Port, 1 GB Flash card, Internal modem for remote diagnostic access link, & 12" TFT Flat screen monitor. -- Line control (no limit switches) for workstation functions. -- Heavy-duty feed chain, with 2.2 kW (3 HP) Motor, Rubber pads, & Automatic chain track lubrication. -- Motorized top pressure beam with 0.14 HP (0.10 kW) Motor. -- Outboard panel support, with Roller guide & 1,000 mm (39.37") Adjustment. -- Sound enclosure.Workstations: -- Front & rear end trim unit, with (2) 1 HP - 12,000 RPM High frequency motors, 0° - 15° Chamfer, & Programmable pneumatic control for straight or chamfer trimming. -- Top & bottom rough trim unit, with (1) 1.86 kW (2-1/2 HP) High frequency motor. -- Top & bottom fine trim unit, with (2) 0.55 kW (3/4 HP) - 11,300 RPM High frequency motors with Electronic brakes, Servo control bevel, 0° - 25° Tilt, Vertical & Horizontal tracing, Servo control (in/out), & DFC Radius cutters. -- Corner rounding unit, with (2) 0.35 kW (1/2 HP) - 10,940 RPM High frequency motors, & Automatic 2-position edge thickness. -- Quick-change top & bottom profile scraping unit for rigid PVC edges, with Digital quick-set system for 2 - 6 mm (0.08" to 0.24") Radius, Pneumatic indexing, Servo control (in/out), & Pneumatically-controlled blow-off nozzle. -- Top & bottom buffing unit, with (2) 0.3 HP - 2,800 RPM Motors and Vertical & Horizontal tilt.Full Servo Edgebander, with Pre-Mill, Corner Rounding, Pre-Melt, $5,000 Package of Almost New Diamond Pre-Mill Heads, New

Brandt KDF 440C Edgebander

BRANDT - F-13, ...Top & Bottom TrimmerFor simultaneous top & bottom flush/radius trimming of the oversized edgeband on straight & shaped workpieces with inside-and-outside radii.Specifications: -- Top & Bottom edge trim PVC, HPL, and veneer edgings; up to 3 mm max. thickness. -- Manually operated; 1/2" - 2-1/4" panel thickness; 1-3/8" min. inside radius. -- Features: Independent top & bottom trim heads (0.5 HP - 11,800 RPM motor each). -- Built-in air jet blowoff device; 31" x 48" table size; dual foot pedal control.NOTE: Intermittent fault in the Control Panel, which will require replacement.

Brett Inc. Bolter Saw - We can Motor it or Buy W/O Motor

Brewco 4-Head Resaw Seller has a hydraulic unit to go with the machine. No controls. Optional: System can be cleaned up and controls added PER SELLER: this machine is able to pass 7.75" cants it was purchased in Nelson BC 20 years ago it has not run since it is ready to go but has only on off switches and no motor starters per se I have not pulled the machine out to clean and paint and get ready to move it needs cleaned/ painted/ starters for 4-20hp motors/ small hyd unit for feed belt and feed rolls nice machine, I have not operated it but was running when I bought it and has been under cover since will need 5 starters, and a small hyd unit 5 hp, which i can provide this machine is easy to get ready if we have a commitment

BREWCO 44" X 8' 2 STRAND TURN AROUND W/10" POWER ROLL CASE ON EACH END

SN: GEG11827, Model: B1600, 16" x 16' capacity, infeed web was new in Feb., 50 hp electric on saw, 50 hp electron on hydraulic unit, 1 3/4" x 40" bandwheels with oil bath hubs, 2" x 20'4" bands, air band tensioner, hydraulic powered press down roll, runaround has all decks and rollcases, including 5 way board splitter, operators cab with computer setworks and all controls needed, 8 presets for thickness, automated infeed speed control by size of log, has all photo eye sensors needed, lots of extra parts, all electrical and hydraulic hoses were labeled during disassembly for easy setup, includes electric motor starters, taken out of production in June of 2023.

BREWCO 6 Head Horizontal Resaw - includes return conveyor. Visit https://benjones.com/shop/102007/ for more information

Brewco single head resaw, line-shaft ready, working condition

Brewco 1620 Resaw SN: B10009 Has run around Stock photo Please see video

Brewco 2 Head resaw Was in production until mid January Works great More photos coming soon

This system is no longer needed at the current facility. Ready for immediate removal! - Brewco Wolf Resaw - 4" Blade; 20'4" Long - 40" Bandwheels - 40 HP Main Motor - 10 HP Hydraulic Feed - McDonough Style Guides - Some spare blades - Head moves up/down, not the bed - Approximate dimensions: 9'L x 10'W x 6'H - Also available separately: - 8' Infeed Belt - 16' Outfeed Rollcase

Brewco B-1600 Grade Resaw system with resaw 40" wheels, 2" saw blade, 40 HP main motor, 12" infeed belt conveyor, complete infeed transfer system, roll cases, pop up chains, Brewco 5-way board separator outfeed system, 20 HP Hydraulic Pack.

Brewco B-1600 Wolf with Full Run Around System. S/N

Brewco B-1600 16" x 16" with Full Run Around System & 5 Way Seperator S/N BBK0489

Brewco Big Band B-1620 Grade resaw with with Cab and Full Runaround System.

Brewco MDL B-4840 Grade Edger

16" x 16' capacity 50 hp electric on saw 50 hp on hydraulic unit 1 3/4" x 40" bandwheels oil bath hubs 2" x 20'4" bands air band tensioner hydraulic powered press down roll runaround has all decks and rollcases, 5 way board splitter operators cab with computer setworks all controls needed, 8 presets for thickness automated infeed speed control by size of log has all photo eye sensors needed lots of extra parts all electrical and hydraulic hoses includes electric motor starters taken out of production in June of 2023.

Brewco B1650 Resaw No run around but has all controls and hydraulics