Equipment For Sale

COSTA K6 WCCT 1350 4-Head Planer / Sander 4-Head with Planer, Drum, Drum and Combination headSpecifications: -- Front head #1 54" Helical planer head with (480) insert knives 34 kW or 45 HP motor. this is a removable head complete with cart for cleaning and changing knives. -- Head #2 Drum currently set up with 100 grit abrasive sanding belt 22 kW or 30 HP motor., -- Head # 3 Drum with 150 grit abrasive sanding belt 17 kW or 22 HP motor. -- Head # 4 Combi head with timed air bladder platen, currently runs 180 grit abrasive sanding belt, 14 kW or 20 HP motor. -- Feed mat speed from 4 - 20 feet per minute. Features: -- Capable of planning off 1/8" and sanding to 180 grit in one pass. -- Uses 52 - 54" x 103 abrasive sanding belts. -- Vacuum feed mat only surfaced 2 or 3 times, PLENTY of life left in it. -- Used in small shop running no more than 5 -10 hours a week, on a machine designed to run 3 shifts. -- Features Air scrubber unit on the out feed to remove any additional dust. Note: Machine was purchased New in February 2016

COSTA K7 CCCT 650 ... 4-Head Wide Belt Sander, working width 650 mm (25.6") and constant pass line conveyor heightExcellent Veneer and Solid wood sander with (3) Contact rollers and (1) platen.Head Configuration: -- 1st Head: Steel contact roller, 250 mm (9-7/8") diameter, driven by 37 kW (50 HP) motor. Abrasive belt speed 24 m/Sec (78 FPS). -- 2nd Head: Rubber covered contact roller, 250 mm (9-7/8") diameter. Shore hardness 70. Driven by 30 kW (40 HP) motor. Abrasive belt speed 18 m/Sec (59 FPS). -- 3nd Head: Rubber covered contact roller, 250 mm (9-7/8") diameter. Shore hardness 70. Driven by 22 kW (30 HP) motor. Abrasive belt speed 18 m/Sec (59 FPS). -- 3rd Head: Segmented finishing platen, electronically controlled narrow segments conform to panel width and length for thin veneer sanding. Driven by 11 kW (15 HP) motor. Abrasive belt speed infinitely variable 3 - 16 m/Sec (30 - 52 FPS). -- Sanding Belt Info: abrasive belts, air blast abrasive belt cleaning, pneumatic belt tensioning with electronic tracking on all heads. Grit set system for abrasive belt grit compensation. -- At Outfeed: Brush Roller 180 mm (7") driven by 1.1 kW (1.5 HP) motor. Equipped with: -- PLC processor controls with touch screen. Integrated control cabinet. -- Feed System & Conveyor Bed: Min/max. working height 3 - 160 mm (1/8" - 6-5/16"). Variable feed speed conveyor with inverter control 4 - 20 m/Min (13 - 65 FPM). Constant Pass Line at 920 mm from floor (36"). Vacuum conveyor bed assembly. Infeed & outfeed spring loaded hold down shoes on all heads. Powered raise & lower of conveyor bed with LED readout.Also inculed: about $15,000 of sanding belt

2 head brush sander 1350mm wide Vacuum bed panel cleaning

Costa 60CT2-1150 (2)-Head, Wide Belt Sander44" width cap Drum, Combination HeadHead Co figuration 1st Head: Rubber-covered contact roll, 20 HP motor;2nd Head: Segmented polishing platen, (30) narrow segments are electronically controlled to conform to the panel shape and size to minimize veneer sand-throughs, each segment with variable pressure control, 15 HP motor.Specifications: -- Adjustable contact roll for varying thickness of abrasive belts with -- 45" x 103" Abrasive belt, electronic tracking. -- Motorized part thicknessopening on conveyor bed with digital readout, -- Variable feed speed 10 - 50 FPM with inverter drive, -- Vacuum conveyor bed assembly with 4 HP suction fan,infeed & outfeed spring loaded holddown rolls.Equipped with & Features: -- Controls mounted on the front of the machine, -- Instant shut-down safety guard, all motors with Y-Delta starters, and motor load meters.NOTE: Some spec's need to be verified

Costa 53" Sander Model 80 CT 1350 Wide Belt Sander (2) Machines available!

COSTA - KK CC-CCC 1350, ...5-Head Top & Bottom Wide Belt Sander.53" Width capacity; (2) Bottom drums, (3) Top drums.Bottom Machine: -- Constant pass line height: 1,000 mm (39"). -- Motorized infeed conveyor. -- Motorized infeed pressure rollers. -- Sectioned infeed pressure beam.1st Head: -- Rubber covered cylinder ,16" dia., 35 kW motor. -- Intermediate pressure shoe with lips and rubber covered rollers.2nd & 3rd Heads: -- Rubber covered cylinder, 16" dia. (2nd head), 52 kW motor (3rd head), 88 kW. -- Outfeed pressure shoe with lip and rubber covered rollers. -- Vacuum Feed Table: 10 HP (7.5 kW) motor. -- Vacuum set pneumatic for (2) levels of vacuum pull control.Top Machine: -- Infeed roller. -- Motorized infeed pressure rollers. -- Sectioned infeed pressure beam.1st Head: -- Rubber covered cylinder, 16" dia., 35 kW motor. -- Intermediate pressure shoe with lips and rubber covered rollers.2nd & 3rd Heads: -- Rubber covered cylinder, 16" dia. (2nd head), 52 kW motor (3rd head), 88 kW -- Outfeed pressure shoe with lip and rubber covered rollers. -- Vacuum Feed Table - 10 HP (7.5 kW). -- Vacuum set pneumatic for (2) levels of vacuum pull control..Equipped with and Features: -- All drives are equipped with disc brakes. -- Each Sander with vacuum feed belt with fans..

Costa Model 81 C 1350 Wide Belt Sander

Log press as pictured Main motor (k) 15 Auxiliary motors (K) 1,5 + 1,5 Operating pressure (Bar) 170 - 210 Hourly production with wood chips and sawdust (kg) 120 - 150 Briquette @ (mm) 70 Briquette Length (mm) 30 - 300 Weight (kg) 1650 2180 Dimensions in millimetres (mm) 1700 1720

Cousins LP2100X Wrapping Machine 115 Volt 1 Phase

Cousins LP-SW Wrapper 115Volt 1 Phase Folded down for shipping

Cousins Stretch Wrapper Model LP-SW s/n 250511-5L 9079

Covel Grinder

CP MANUFACTURING - S100-6-LH-US, ...Screens -- (1) System of (2) Screens -- Very lght Use -- Ordered as part of a Single-Stream Sort System that was designed to run 10 Tons/Hr -- 1-Feed Conveyor -- Each: 14,500 Lbs -- Loaded onto your Truck

CAN-PAK - CD-3000: Complete Can Densifier -- Motor: 25 HP.Dimensions• Height: 9’-2";.• Width: 3’-10";.• Length: 13’-5";.• Machine weight: 8,000 Lbs.• Conveyor weight: 1,000 Lbs.• Conveyor: 11’-5"; High x 20-1/2"; wide x 13’ long.Specifications• 25 HP Power unit.• 460 Volt, 3-phase wiring.• Solid-state programmable controller.• Thermostatically controlled hydraulic oil cooler.• 1 Cubic yard hopper.• 120-gallon hydraulic tank.• 20-1/2"; Wide infeed conveyor with: 3/4 HP Motor. Direct drive gear reducer. Magnetic head pulley. Steel reject chute.

CP100 Can Flattener --220V, 1200 lbs per hour --Infeed Conveyor --Magnetic Separator -- New belt included

CP CD1000 CAN DENSIFIER -- 900 to 1,500 Lbs/Hr capacity -- Fully automatic solid-state Controller -- Density: 40 Lbs per cu. ft. allowing 140,000 Lbs in 50' railcars or 40,000 Lbs in 40' Trailers. -- 10 HP - 3/60/208/230/460 Volt Hydraulic Power Unit

CPM Model 2A2 Vertical Pellet Cooler Rated up to 10 TPH on 1/4" Pellets

CR Onsrud 288 G18 CNC Router Size: 61" x 288" Machine Head Details: Main Head 18Hp HSK63F w/12 Position ATC 18 Hp Spindle – Powering through materials like a hot knife through butter. Accessories: 40 Hp Dekker V- Maxx Vacuum Pump 24,000 RPM, 12 Tool Capacity, 11" Z- Stroke Machine Table: Zone Plumbed Vacuum System Tool Capacity: Pop Up Part Positioning Pin. Power Requirements: 440 Voltage 60 Cycle 3 Phase

Onsrud M Series CNC Router 5'x12' Table Vacuum pump Includes: Nederman S1000 Dust System

- Dual Supported Gantry: Enhances stability and precision with independent servo motors and drives on both sides. - 18 HP Spindle: High-power, fully programmable, and capable of reaching 24,000 RPM, suitable for a wide range of routing and drilling tasks. - 5'x20' Phenolic Vacuum Grid Table: Ensures superior material hold-down through vacuum zones, ideal for flow-through spoil boards or dedicated fixtures. - Integrated Dust Collection System: Keeps the work area clean with integrated dust extraction hoods for chip removal during operations. - 12-Tool Dynamic Automatic Rotary Tool Changer: Facilitates efficient tool changes, with a fully servo-controlled system for quick transitions between tools. - OSAI PC Front Series Controller: Provides advanced control options with a high-resolution touch screen, PLC capabilities, and compatibility with AlphaCAM for programming automation. - 11-inch Z-Stroke: Suitable for various materials and applications, offering flexibility with under-bridge clearance. - 2-Year Warranty: Includes full parts and labor coverage, ensuring reliability and long-term operational support. Included Options: - 9 Spindle Drilling Block Package: Allows for simultaneous or independent drilling along the X and Y axes. - Pneumatic-Controlled Vacuum Table Switch: Actuated via a push-button or PLC control for precise operation. - 20 KVA Isolation Transformer: Ensures stable power supply and noise filtering for optimal performance.