Equipment For Sale

Cornell 620 Single Arbor Gang with Sizer

Cornell Chop Saw. Located in NY. #C915

1995 Cornell 915 LH Drop Saw Trimmer S/N 008-8-95 Out and Ready to Ship

Cornell 8" Double Arbor Gang Saw. #C860

Cornell Belt Conveyor 12" x 4'6" Long with Hydraulic Drive

Cornell Combo Gang Edger with Controls and Infeed. model: HD426 s/n: HD426-7004-7-92

Cornell 823 3 Saw Edger s/n: VEG-48-848-3-95

Cornell VS1 Lumber Stacker S/N PS155

35' Barn Sweep

Chip Blower No Motor

Cornell Double End Trim Saw

Cornell 50HP Material Blower

Cosmic Fox 13 and Fox 16 CNC Router New machines

COSMEC NR32-16CUK 510 CNC Router with ATC and Boring:63" x 122" Fixed table: Moving gantry design in a front-to-back configuration; 2-zone Phenolic vacuum table with pop-up pins for part location. -- Equipped with:(1) 10 HP "HSD" ISO 30 Type ATC spindle, 8-position side-mount tool carousel, variable spindle speed from 800 - 18,000 RPM, 11" Z-axis stroke. -- Boring unit:(1) 17-Spindle boring block (11) vertical and (6) horizontal and X-Axis - 5,000 RPM. -- Axis travel: X-Axis travel 3,190 mm (125.6"), Y-Axis travel 2,010 mm (79.1"), Z-Axis travel 280 mm (11.0"); Z-Axis clearance under rail 250 mm (9.84") - Rapid traverse on X- & Y-axis 38 m/Min (1,496 IPM). -- Control:OSAI series 10 numerical control with screen and including, 3-axis linear & circular interpolation, and RS 232 connection with a user-friendly operator interface. -- All axes Incorporate brushless, closed-loop Servo motors driving precision ball screws and ride on STAR linear guideways with an automatic lubrication system servicing the way and ball screw bearings. -- Complete with:Vacuum pump, assorted tool holders, and manuals.

This Cosmec Conquest 250 CNC router with a 4x8 vacuum table is being listed for parts or as a restoration project. The CNC did run prior to being shipped to our shop a couple of years ago, but it has not been wired to power since then, and the working status is unknown. If you have a Cosmec CNC that needs parts replaced then this would be a great machine for you. Included in the listing are two Becker vacuum pumps (see photos for details) that could be can be hooked to this machine or plumbed to another.

Cosmec CM100 12" Dip Chain Gang Saw Parts Machine Only

COSTA KH2 CCCT 1350 Wide Belt Sander, (4) Heads52" Width cap. Drum, Drum, Drum, PlatenHead Configuration:1st Head: Steel contact roll, 9-7/8" dia, 45 HP motor;2nd Head: Rubber covered contact roll, 9-7/8" dia, 45 HP motor.3rd Head: Rubber covered contact roll, 9-7/8" dia. 60 shore, 30 HP motor.4th Head: Finishing Platen, 23 HPSpecifications: -- 53" x 103" Abrasive belts, air blast abrasive belt cleaning, pneumatic belt tensioning with electronic tracking. -- Controls with PLC processor, -- Pneumatic grit compensation with 4-position stops. -- Variable feed speed conveyor with inverter control 16 - 82 FPM.Equipped with & Features -- a Vacuum conveyor bed assembly with a 5.5 HP suction fan and motor. -- Infeed & outfeed spring loaded hold down shoes on all heads. -- Powered raise & lower conveyor bed with LED readout and motor load meters.

A. Costa Spamatic 220 Molder

COSTA - KBH CCCT 1350 & KH2 CCCT 1350, ...Top & Bottom Sander Line.Head Configuration:Machine #1 - "KBH CCCT" 4-Head Bottom Sander. Bottom Head #1: ~10" Dia. grooved Steel Drum, 47 HP motor. Bottom Head #2: ~10" Dia. grooved rubber covered contact drum, 47 HP motor. Bottom Head #3: ~10" Dia. grooved rubber covered contact drum, 32 HP motor. Bottom Head #4: Finishing platen, 23 HP motor.Machine #2 - "KH2 CCCT 1350" 4r-Head Top Wide Belt Sander. Top Head #1: ~10" Diameter Grooved Steel Drum, 47 HP - 460 V motor. Top Head #2: ~10" Grooved rubber covered contact drum, 47 HP motor. Top Head #3: ~10" Grooved rubber covered contact drum, 32 HP motor. Top Head #4: Finishing platen, 23 HP motor.Specifications: -- PC User interface for each machine. -- Sanding belt size: 53" x 103". -- 96" Belt conveyor in between machines. -- 20 HP Vacuum Blower for each machine's vacuum bed.

--This machine is in Auction @ https://exfactoryauctions.com/Detail/FD-230117/event/A122024$1. --Low starting bid! Equipped with: 1st & 2nd Heads: Each with 2” W Cross brush belts, 2.5 kW (3.35 HP) - 1,690 RPM Motor, Rotating belt on vertical axis supports series of pads with abrasive paper, Pads are adjustable to vary angle of contact on panel during rotation of belt, Pads with abrasive strip makes contact with workpieces from both sides as it rotates. (3) 2” Dia. Rubberized hold-down rolls, (1) before and after each cross brush belt head. 3rd & 4th Heads: Each with 62” L x 16” Dia. Brush Roll & 2.5 kW (3.35 HP) - 1,140 RPM Motor, & Horizontal angle adjustment. 2-5/8” dia x 7/8” w swivel rubber wheels before each brush roll head. (1) 2” Dia. Rubberized hold-down roll after last brush roll head. 53-1/2” W x 12’ L Vacuum feed belt, with 2.64 kW (3-1/2 HP) - 1,695 RPM Motor, Holes on 1-1/2” W & 2” L Centers, 2-1/2” Dia. Rubber-covered infeed & outfeed rolls, Motorized adjustment with Digital readout with LED Display. Control motor load meters. Complete with: Instruction Manual.