Equipment For Sale

Pendu 6100 Saddle Notcher S/N 9902

4 Small Blowers to Choose From.

Pendu 2800D Dado Machine S/N 9901

Complete Cut-Up Line –– Pendu Junior Gang Saw, Deutz diesel, blower, dust pipe, cant deck, Morgan Standard Chop Saw, 24" blade, single phase, dead rolls and stops. $32,500 276-692-6322 or 276-694-4276

Pendu 3000 Inline Slitter Saw w/Extra Blades

4300 Pendu Gang Saw with 4400 Pendu Stacker. Located in MI. #C969

2010 Pendu 6800 Scragg. Located in WI. #C925

Pendu 5000 Gang. Originally built with a diesel motor. The diesel has been removed and can be replace with an electric motor.

Includes infeed, outfeed with adjustable air stops, and cab with controls. Cutting cap. 9? x 12?

PENDU - 3800, ...Stake PointerPENDU's "High-Speed Stake Pointer" is designed for high volume production of surveying & agricultural pencil point stakes.Includes: Hopper fed material size range from 3/4" - 2 1/2" square or rectangular material and 16" - 72" in length. -- Equipped with: Aluminum housing round cutterhead with: Replaceable knives; powered by a 10 HP - 3,600 RPM motor; shaving the end of the stakes to a pencil point. -- Automatic feed via: 3 HP Variable speed electric drive; outfeed for pointed stakes on (6) arm staging station; pneumatic clamping to secure part during cutting. -- Complete with: Fabricated steel construction; chip shield with dust shroud for chip extraction; pre-wired Operator Control Console.Unit is capable of producing up to (2,700) stakes/Hr.

Pendu 4400 Lumber Stacker

PERDURE model P006 Wood Torrefaction Line with Propane Heating;Oven roasting type complete with the following components and features: -- (6) Meter-long treatment Chamber. -- 1.2 Million BTU propane Heater (or convert to natural gas). -- Afterburner. -- Entrance and exit Conveyor with motorized Trolleys. -- (2) Sliding Doors closed with electric Jacks, -- (2) Stirrers, -- (2) Burners, -- (1) Main Fan -- Water Circuit. -- PCI INDUSTRIES Multi-zone Climate Control System based on thermocouple temperature measurements. -- The setup is equipped with a system for heat recovery and combustion (afterburner) of volatile organic compounds (VOCs) emitted by the wood, which results in reduced energy consumption. -- Final treatment of the product load is cooling by water injection.NOTES: &#9679 The PERDURE process is distinguished by relatively short processing times (7 to 16 hours depending on the species and the thickness of the parts processed) and the low loading capacity of the ovens (approximately 3 to 8 Mbmp). &#9679 The original 2006 purchase was $ 991,000.00 in Canadian funds.

2014 Peterbilt Bucket Truck with 105’ bucket reach, 3,000 lb Jib, Rear mount, Work Ready. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

#200 • 2021 Peterbilt Truck Update: Has Engine: Cummins CX15. Transmission: Eaton Fuller 13 speed. Front Axle Rating: 12,000 lbs. Rear Axle Rating: 20,000 lbs. GVWR: 52,000 lbs. Meter Reads: 235,701 mi. -- Features -- Tire Size: 11R24.5. Wet Kit: no. Heat: yes. -- Seller Statement -- Air ride, excellent operating condition

2004 PETERBILT TRI AXEL DUMP TRUCK 619,161 MILES ON CHASSIS NEW ENGINE C-15 8LLHEAVY SPEC GOOD TIRES AND BRAKES GOOD CONDITION FINANCING AVAILABLE WITH NO MONEY DOWN 3 MONTHS NO PAYMENTS WITH GOOD CREDIT GRANITEHE.COM

158000 miles clean truck Paccar mx13 14,600 front end 46,000 rears Locking rear ends also available with a 2020 48’ deloupe tri log trailer for additional cost

2020 Peterbilt 567 Sleeper Semi Truck 228,000 miles 565 HP Cummins 1X15 18 speed manual trans 3.36 rears Double frame heavy spec 46,000 rears 13,200 steer 3 stage jake Wet line New clutch by Peterbilt 48" flat top sleeper

1997 Peterbilt Sleeper 2.1 mil miles 13 speed reman tranny 3 years old 390 rears 63" bunk Cat 3406E 350k miles on engine since platinum rebuild by Cat Fiberglass front and rear fenders Both rear ends rebuilt including housings Roard ready Retiring PRICE REDUCED

2016 PETERBILT 567 CAB AND CHASSIS TRUCK 366,000 MILES ISX 13 CUMMINS ENGINE 10 SPEED GOOD FRAME GOOD BRAKES GOOD TIRES 40K REARS 16K FRONT VERY GOOD CONDITION WE CAN FINANCE ANY DUMP BODY OR OTHER INTO PURCHASE FINANCING AVAILABLE WITH NO MONEY DOWN 3 MONTHS NO PAYMENTS WITH GOOD CREDIT GRANITEHE.COM

1981 Peterbuilt 359 -324,000 miles -CAT 3406B -15 speed transmission -Jake brake -Mack camel back -38k rears 12k front -Older truck so has its seeps but overall solid rig