Equipment For Sale

WEIMA C 150 Briquette PressSpecifications & Features: -- Produces 2" (50 mm) dia. Briquettes; -- Hopper opening of 41" x 41" (1,040 x 1,040 mm); hopper volume 1.43 cu/yd (1.1 cbm). Equipped with: -- 9 HP Hydraulic motor; 0.75 HP auger motor; hydraulic oil volume of 26.4 gallons (100 liters). -- Vertical hydraulic ram compacts the material in the extrusion chamber to produce uniform material; extrusion chamber is continually filled via rotary screw type auger. -- Volume reduction from chip/dust to block up to 10:1 ratio at 2,600 PSI; hourly output up to 80 - 120 Lbs/Hr ("quoted output is an average and can be influenced by density, material size, screen size, feeding form, and other factors").Features: -- Briquette length control, chrome plated clamp, oil level switch, control panel side-mounted to hopper, and overheating protection for hydraulic oil. Solid German engineering. - Freight, start-up, discharge pipes, etc. not included.

WEIMA Grinder - 2004 Model WLK 13/75 Low Speed, Hopper Style Grinder. Batch style grinder with 75 HP low-speed rotor, top feed hopper, self-contained hydraulic system with hydraulic ram, and controls. Controls operate the ram, which forces material against the low-speed rotor. Controls vary the hydraulic pressure based on the load on the rotor motor. Features reversible carbide cutters on a large diameter rotor, a 2 cubic yard hopper with a 51 x 47 inch top opening. Weighs about 10,000 lbs. Serial 500-6283.

WEIMA ZM-30 Quad Shaft 4-Shaft ShredderEquipped with: Model- ZM 30 S -- Unit was used to shred wire (6,000 – 8,000 lbs per hour) --20mm screen included 25 HP x 2 --480V- 3 phase --Cutting chamber is 19"; x 27"; Hopper is 33"; x 48"; --The ZM30S is a beefed up version of the ZM 30. Unit has the same size motors, shafts and cutters as the ZM 50 but with a shorter shaft length

WEIMA ZM-40 Quad Shaft 4-Shaft ShredderEquipped with: -- Dual drive motors - (2) 30 HP Drive motors. -- Hopper opening measures 51" x 55.1" (1,300 x 1,400 mm); cutting chamber opening of 30" x 27.6" (762 x 700 mm). -- Rotor length of 30" (762 mm); Rotor speed 25 RPM; cutting disc 11" (280 mm) diameter. -- Complete with: -- Control Panel with soft start and 16' cable bundle. -- Note: "Quad Shaft" Shredders, unlike Dual Shaft Shredders, allow shredded material to be circulated through the cutting chamber until it is small enough to pass through the sizing screen. -- Machine weight: 5,500 Lbs.

WEIMA ZM-40 Quad Shaft 4-Shaft ShredderEquipped with: -- Dual drive motors - (2) 30 HP Drive motors. -- Hopper opening measures 51" x 55.1" (1,300 x 1,400 mm); cutting chamber opening of 30" x 27.6" (762 x 700 mm). -- Rotor length of 30" (762 mm); Rotor speed 25 RPM; cutting disc 11" (280 mm) diameter. -- Complete with: -- Control Panel with soft start and 16' cable bundle. -- Note: "Quad Shaft" Shredders, unlike Dual Shaft Shredders, allow shredded material to be circulated through the cutting chamber until it is small enough to pass through the sizing screen. -- Machine weight: 5,500 Lbs.

WEIMA WL-6 Low Noise Vertical Hopper Waste Grinder Specifications: -- Low noise hopper-fed grinder with a 10" dia X 31.5" long rotor and a 24HP drive package that includes a 2-sided flared hopper. -- Vertical 1.3 cubic yard hopper with 31.5" x 39.2" (800 mm x 900 mm) opening. Equipped with: -- (21) Recessed concave cutters with low clearance over the rotor to extend cutter life, protect the bolts, and reduce machine wear. -- Rotor operates at 80 - 100 RPM with outputs ranging from 1,000 - 34,000 Lb/Hr depending on screen size and material.Includes: -- Control panel.(4,926) Total operating hours.

WEIMA WL-6 Low Noise Vertical Hopper Waste Grinder Specifications: -- Low noise hopper-fed grinder with a 10" dia X 31.5" long rotor and a 24HP drive package that includes a 2-sided flared hopper. -- Vertical 1.3 cubic yard hopper with 31.5" x 39.2" (800 mm x 900 mm) opening. Equipped with: -- (21) Recessed concave cutters with low clearance over the rotor to extend cutter life, protect the bolts, and reduce machine wear. -- Rotor operates at 80 - 100 RPM with outputs ranging from 1,000 - 34,000 Lb/Hr depending on screen size and material.Includes: -- Control panel.

Weima WLB 1300 Horizontal Grinder 50 HP Motor System works, not currently in use, will need main bearing replaced.

WEIMA - WLB 400, ...Horizontal Low Speed Grinder Equipped with: -- 25 HP Rotor motor; rotor with (18) 4-way indexable, replaceable cutter knives. Features: -- Top infeed roller; 15-1/2" x 2-1/2" feed opening; Heavy-Duty Industrial Grade construction with stress relieved shell and frame; Heavy-Duty outboard roller bearings; separate electrical control panel. Complete with: -- 8" Dia. collection outlet; 3/4" screen.

WEIMA - WLB 400, ...Horizontal Low Speed Grinder Equipped with: -- 25 HP Rotor motor; rotor with (18) 4-way indexable, replaceable cutter knives. Features: -- Top infeed roller; 15-1/2" x 2-1/2" feed opening; Heavy-Duty Industrial Grade construction with stress relieved shell and frame; Heavy-Duty outboard roller bearings; separate electrical control panel. Complete with: -- 8" Dia. collection outlet;

2020 Weima WLH 600 Grinder 50 HP motor Vibrating Infeed

WEIMA WLK 10 Vertical Hopper-Fed Low-Noise Grinder Equipped with: -- 39.4" x 47.2" Hopper opening at the top, 1.7 cu. yds. cap.; (3) sides straight with curved Front Wall. -- 60 HP rotor motor, 14-1/2" dia. The patented "V-ROTOR" design utilizes a V-groove rotor closely matched to grooves in the counter-knife to ensure uniform discharge free of splinters, reduce friction, and dedicate more horsepower to grinding. -- 39.4" Long rotor operates at 60 - 120 RPM; equipped with (52) replaceable back bolt-on (4 x indexable) concave-shaped cutter knives. -- Welded knife holders standard; recessed concave cutters with low clearance over the rotor extend cutter life, protect the bolts, and reduce machine wear. Features: -- WEIMA'S proprietary gearbox is designed specifically for slow-speed grinders. -- 8" Dia. outlet for material discharge via auger, conveyor, or pneumatic (1,900 CFM required for pneumatic conveying); choice of 3/8" - 2" interchangeable screens to produce chips from 1/2" to 2" (Output depending on screen size, material density, and moisture content). -- Hydraulic ram optimizes feed pressure by monitoring rotor motor amperage, lateral force on the ram is minimized by a unique "U-Joint" mounting system. Complete with: -- Heavy Duty structural steel frame, welded construction; integrated "plug-and-play" electrical control system with UL-approved components (system UL certification available upon request for an additional charge). -- Ground material output depends on screen hole size and material from 1,200-2,500 Lbs/Hr.; 3/4" holes are supplied standard screen hole size. Options: -- Flared hopper, material discharge auger; programmable logic controls, and ram comb.

WEIMA WLK 13 Vertical Hopper-fed Low Noise Grinder Specifications: -- Single shaft Shredder/Grinder, 51" x 47" hopper opening (straight sided), 2 cu. yds. cap.; 368 mm (14.5") rotor dia. x 51.2" rotor length; 60 HP motor and hydraulic ram. -- Equipped with: -- Patented "V-ROTOR" design utilizes a V-groove rotor closely matched to grooves in the counter-knife to ensure uniform discharge free of splinters; reduce friction, and dedicate more horsepower to grinding. -- (68) welded knife holders, recessed concave cutters with low clearance over the rotor to extend cutter life, protect the bolts, and reduce machine wear; drop out discharge, lift up door for easy purge cleaning when used in plastics application. -- Hydraulic serrated ram optimizes feed pressure by monitoring rotor motor amperage, lateral force on the ram is minimized by a unique "U-Joint" mounting system, Hydraulic clutch enables motor to start with the hopper full. -- Features: -- Heavy Duty structural steel frame, welded construction; integrated "plug-and-play" electrical control system with UL approved components (system UL certification available upon request for additional charge). -- Recommended for plastic, paper or wood applications.

WEIMA WLK 15 Vertical Hopper-fed Low Noise Grinder Specifications: -- Single shaft Shredder/Grinder, 59" x 59" rear-flared hopper opening; 3 cu. yds. cap.; 368 mm (14.5") rotor dia.; 120 HP motor; hydraulic ram with 4-sided serrated ram. -- Equipped with: -- Patented "V-ROTOR" design utilizes a V-groove rotor closely matched to grooves in the counter-knife to ensure uniform discharge free of splinters; reduce friction, and dedicate more horsepower to grinding. -- (82) Welded knives, (4) broaching cutters & (4) counter-knives, recessed concave cutters with low clearance over the rotor to extend cutter life, protect the bolts, and reduce machine wear. -- Features: -- Drop out discharge, hydraulically actuated lift up door for easy purge cleaning; extended screen basket; cut-out for conveyor (not included); false wall; 3/8" - 4" screen available. -- Hydraulic serrated ram optimizes feed pressure by monitoring rotor motor amperage, lateral force on the ram is minimized by a unique "U-Joint" mounting system, Hydraulic clutch enables motor to start with the hopper full. -- Complete with: -- Heavy Duty structural steel frame, welded construction; integrated "plug-and-play" electrical control system with UL approved components (system UL certification available upon request for additional charge). -- Recommended for plastic, paper or wood applications.

WEIMA WLK 4 Vertical Hopper-Fed, Low-Noise GrinderSpecifications: -- 31-1/2" x 39" Hopper opening at the top, 1.1 cu. yds. cap. Features: -- 30 HP rotor motor, Patented "V-ROTOR" design utilizes a V-groove rotor closely matched to grooves in the counter knife to ensure uniform discharge free of splinters, reduce friction, and dedicate more horsepower to grinding. Equipped with: -- (14) Replaceable back bolt-on cutter knives, welded knife holders standard, recessed concave cutters with low clearance over the 10" dia. rotor extends cutter life, protects the bolts, and reduces machine wear. -- 6" Dia. dust collection outlet (1,200 CFM required); 3/8" - 2" interchangeable screens to produce chips from 1/2" to 2" (Output depending on screen size, material density, and moisture content); -- Hydraulic ram optimizes feed pressure by monitoring rotor motor amperage, the lateral force on the ram is minimized by a unique "U-Joint" mounting system. Includes: -- Heavy Duty structural steel frame, welded construction; integrated "plug-and-play" electrical control system with UL approved components (system UL certification available upon request for an additional charge). Options: -- Flared hopper, log Spacer, 2nd row of knives, material discharge auger; programmable logic controls;

WEINIG - UNIMAT: 10005-Head (B-R-L-T-B), 9-1/16" x 4-3/4" cap. -- Head sequence: Bottom 10 HP; right 15 HP; left 15 HP; top 25 HP; 20 HP motor. -- WEINIG "Memory Re-Dial" System with: Storage of (100) separate profiles; electronic LED readouts for all spindles. -- Spindle dia. 1-13/16" with Cutterhead speeds: Spindle #1 at 6,000 RPM; spindles #2 - #5 at 7,000 RPM with high precision bearings & mechanical spindle brakes; adjustment of vertical spindles 3-1/8" axially. -- Electronic LED readouts for: Chip breaker & pressure elements for top spindles. -- Cutting circles: 8-7/8" On spindles #2 - #5; vertical spindles with adjustable table plates to cutting circles; hardened infeed bed plates before-and-after 1st bottom head. -- Motorized feed beam adjustment; variable feed speed from: 20 - 118 FPM; 10 HP inverter controlled Cardan feed drive, overhead feed wheels with pneumatic pressure. -- (1) Powered table roller in bed at outfeed. -- Infeed straightening table 2 M (6-1/2') with adjustable fence; adjustable table at outfeed. -- Equipped with: Central location of lubrication points; side pressure roller at infeed; manual Waxilit pump; (2) lights inside sound enclosure. -- Includes Set-Up Stand.NOTE: Machine is in good running condition, but electric brakes are not functional; does not affect running or performance.

WEINIG - U 1000: Feed Through Moulder6-Head (B-R-L-T-T-B); working cap. of 9-1/16" x 4-3/4".Specifications -- Head sequence: Bottom 10 HP; right 15 HP; left 15 HP; top 25 HP; top 20HP; bottom 20 HP motor. - All spindle motors with mechanical brakes. -- WEINIG Memory Redial system allows for: Storage of over (200) separate profiles; electronic LED readouts for all spindles, chipbreakers; pressure elements. -- Spindle dia. of 1-13/16"; spindle #1 at 6,000 RPM; spindles #2 - #5 at 8,000 RPM with high precision bearings; adjustment of vertical spindles: 3-1/8" Axially. Feed -- Motorized feed beam adjustment with independent adjustment of top head; cutting circles 8-7/8" on spindles #2 - #5. -- Variable feed speed from: 20 - 118 FPM; 10 HP inverter controlled Cardan feed drive; overhead feed wheels with pneumatic pressure. -- Vertical spindles with: Adjustable table plates to cutting circles; hardened infeed bed plates before & after 1st bottom head. -- (1) Powered table rollers in bed at outfeed. -- Infeed straightening table 2 M (6-1/2') with: Adjustable fence and adjustable table at outfeed; chromed tables and fences. Central location of lubrication points; electromagnetic interlocking of safety hood; manual WAXILIT pump. -- Complete with: Axial adjustment of feed roller opposite left spindle & (1) light inside sound enclosure; all setup tools, manuals and spacers.

WEINIG - UNIMAT - 23E: Moulder (Feed Through)6-Head (B-R-L-T-T-B); working cap. 9-1/16" x 4-11/16" -- Head Sequence. Bottom 20 HP; right & left 20 HP; top 20 HP; top 20 HP; bottom 15 HP motor. -- Spindles Dia. 1-13/16" with: Cutterhead speed: 6,000 RPM; DigiSet readouts for left & top spindles; mechanical readouts all other spindles including chipbreaker & pressure element. -- Feed System. Feed motor: 5 HP; variable speed: 20 - 78 FPM.(1) Powered feed roller at outfeed end on the machine.Infeed. Straightening 2 M (6-1/2') table; side pressure roller mounted to infeed table. -- Features. Central lubrication System: Table inserts for right/left vertical spindles; manual Waxilit pump. -- Full sound & safety enclosure; operator/spare parts manuals.

WEINIG UNIMAT 23 ATS, 6 HEAD MOULDER6-Head (B-R-L-T-T-B), working capacity 9-1/16" x 6" profiling. -- Head sequence: Bottom 10 HP, right & left by 15 HP, top 20 HP, top 15 HP and bottom 15 HP motor; Spindle dia. 40 mm with cutterhead speed of 6,000 RPM. -- WEINIG ATS (Automatic Tool Setting), Storage for up to (99) profiles; automatic positioning (radially) of left and top spindles (linked). -- Mechanical digital readouts on all other spindle adjustments for both axis, radial adjustment only on 1st bottom head. -- Motorized feed beam adjustment with independent adjustment of top heads, Receding chip breakers on left and top heads. -- Feed motor 7.5 HP, variable speed 18 - 118 FPM, overhead feed wheels with pneumatic pressure, (2) powered rollers in machine table. -- Large tool cutting circles, table plates adjustable to the cutting circle on vertical spindles with axial adjustment of 3-1/8" for multiple profiles. -- Infeed straightening table 2 M (6'6") with adjustable fence & adjustable outfeed table. Side pressure roller mounted to infeed table. -- Includes: Central lubrication, full sound/safety enclosure, manual bed lubrication pump.