Equipment For Sale

Heavy Duty Newman KM-1 Single Head Notcher w/ motor & starter box, w/ indexing head that will notch to unlimited length (3 ph, air cylinder needs rebuilt), Ref #155 Call Rachel 931-797-6284

Newman Power Feed 24"x12' rollcase with spiral positioner, infeed to planer, electric variable drive

Newman KM16 Trim Saw Has been 90% rebuilt with new main shaft, bearings, chains, aluminum slides, sprockets etc. Has electrical box with starters 10 hp motors Off bearing and waste conveyors Comes with 21’ incline waste conveyor

20’ lengths | All components inspected and replaced as required | Entire shaft was removed, inspected, polished and re-installed. | New roller chain | New lugs | New UHM slides

NEWMAN 990 Planer-Matcher 16 knife heads 6-roll fabricated frame 12" width capacity 6" thickness capacity Side head servo positioner Top head servo positioner Factory (Newman) conversion electric feed roll drive with 6 individual drive motors and direct coupled PlanetGear speed reducers on each feed roll. (25 HP) 150 HP Top Head 100 HP Bottom Head 75 HP Left Side Head 50 HP Right Side Head Several spare side heads Spare 75 HP left side head motor All standard TEFC motors All air and hydraulic valves are new in 2019 Also includes 2019 Newman pineapple feed table with electric drives 3 each 20 HP direct drives on top feed rolls with PlanetGear Reducers 1 ea 25 HP direct drives on top feed rolls with PlanetGear Reducer Newman bridge with direct drive and PlanetGear Reducer 2019 aux hydraulic pump unit for press roll positioning & pressure bar Omega moisture detection & marking equipment 5-strand deck 16' wide x 11' long with hook stops, with tipple on tail end, with additional short 55-strand integrated into the feed table.

Used Newman KM-16 sold as is. 4th head pivots for 45 degree cuts.

Used KM-16 sold as is. Qty. 4 heads, ability to cut 16' lumber. No Controls.

NEWMAN/Cameron - KF-24: Dip Chain Gang Rip Saw with CAMERON "34H-M1" Infeed SystemSpecifications -- Saw Arbor: 24" Arbor cap.; 14" max. dia. tooling; 4" max. motorized thickness adjustment;22" min. length for glue joint accuracy; 6" throat. -- 2-13/16" Dia. arbor; 24-1/2" capacity saw sleeve arranged for 3-1/8" dia. bore saw blades; saw blade options: 10" - 14" Dia.; spacers: 4-5/8" dia. includes: (1) Saw sleeve and spacers. -- 75 HP - 3,600 RPM TEFC Direct drive motor; arbor with: Disc brake & load meter; arbor lockout on the access door. Feed & Chain: -- 5 HP Variable feed speed: 20 to 100 FPM with: Jam arbor protection. Dip bed carried on: 5" Pitch hardened Double-V chain; hardened dip cams; extruded structural aluminum feed bed slats with: Replaceable steel-backed rubber insert strips; automatic chain oiler with low level shutoff. -- (2) 4" Dia. air loaded overhead pressure rolls; spring-loaded overhead bed plate; pressure rolls & bed plate unit with motorized adjustment; slide type infeed guide with: Handle block; either side of the guide can be used for a stock engraver. -- Anti-kickback finger system with: (1) Lower & (2) upper on infeed; (1) upper kickback on outfeed. Equipped with & Features: Upper outfeed main dust hood: 7-7/8" Dia. 2,150 CFM Infeed dust hood 4-7/8 dia. (855 CFM). (1) Spare sleeve; (2) setup fixtures; generous array of spacers (see photos).

Newman Whitney KNO 24 trimmer, S/N 24120897, will pass a 5 1/2" cant, (9) station w/ individual motors, built-in wood waste block conveyor, used on dry line, good condition (ref# 200). This machine has just been removed It is setting inside and ready to load on your truck.

Newman G-200 Knife grinder

9 Blade station w/ individual motors, built-in powered waste conveyor Working when removed from service in 2018. Removed from service because plant ceased operations.

This Newman HP-688 press is powered by a 10 HP hydraulic pump. It consists of two 30? X 74? bays. Each bay has (3) individual 24? X 30? platens. Each platen is 15/16? thick and it’s back structure is webbed every 5-1/2? X 7-1/2?. Each platen is driven by a 5? hydraulic cylinder with it’s own control. The max daylight opening is 48? while the minimum is 37?. On the bottom you will find pop up bed rolls. Over all the press is in excellent condition, is extremely heavily built. This fully functional machine has been fully cleaned, checked, and is ready to work

Newman Knife Sharpener

Newnes 3HP HPU

The A1 Nicholson Debarker, a 1978 model, is a sturdy piece of lumber processing equipment, known for its reliability in the sawmill industry. This used debarker features a 5-arm ring mechanism, designed to efficiently strip bark from logs, enhancing the overall processing speed and productivity. Offered as a complete unit without a cab, it is ideal for operators who require a dependable debarking solution tailored for high-volume operations. Built with durability in mind, this model is well-suited for continuous use in demanding environments. Despite its age, the A1 Nicholson Debarker remains a workhorse in the field, proving to be a valuable asset for sawmill operations seeking cost-effective and robust equipment. Its straightforward design ensures ease of maintenance, allowing for long-term performance and relatively low operational costs. This debarker does not include a cab, providing flexibility for integration into existing setups or for those preferring open-air operation. A practical choice for enhancing the efficiency of your lumber processing workflow, the A1 Nicholson Debarker is an excellent addition for businesses aiming to improve their processing capabilities without making significant investments in new equipment.

Model 27 A7 high-speed ring debarker with air seal ring. Ideal machine for feed speeds from 300-350 fpm or faster on small logs.

2018 Nicholson A8 22" RH Tandem Ring Debarker

2007 Nicholson A6 35" Ring Debarker S/N N7555

Nicholson A-5 22" Ring Debarker

Nicholson Flat Drum Chipper 9'5' x 55" Includes: Trailer, AC power, belt conveyor, switch gear option. System chipped just over 120 truckloads