Equipment For Sale

HMC 2 Saw Vertical Edger 30HP Motor

HMC Model; 1DC, AC carriage drive, complete unit ready to work

HMC 2-Saw Trimmer Model ET-10,;Complete with the following features: --16′ capacity. --Push Button Setworks. --Left hand (feeds from left to right). --Cuts up to 8″ thick. --Belt Conveyor for waste.NOTE: Removed from service and it was running just fine at the time of removal. Stored outside.

HMC MDS-50 Left Hand Drop Saw Trimmer For trimming Boards, Cants, or Ties up to 8" thick and will pass 10" Material. Feed Chains are 81X chain driven by a 3HP Variable Speed Motor with hold downs, each 24" saw is belt driven by 10 HP motors, starters, and fuses are mounted to the Machine in a Nema 12 Enclosure. 0',2',8',10',12',14', and 16' saw units, set up to pass 20' long material. Automatic length trimming with manual override is controlled by programmable control, powered even-ender rolls with a 2 hp drive, and includes one stationary stop gate. Front, back, and top guards are included, and an Automatic shutdown if a door is open while the machine is running. Includes spacers to raise the machine. 360/440 volt

HMC 206 Flat Track Debarker with cab, controls & barnsweep

HMC 8" X 30" X 22' ROLLCASE W/HYD DRV

HMC 3 strand log deck, H-78 chain, stop-load for debarker, 10' 6" wide x 19' long, Tulsa Winch electric drive, very good condition

chain type log turner, sized for 40" carriage, hyd drive, good working condition

This mill is ready to be removed from the current location. - 4 Roll Cases 24’’ 2 center 6.5 Diameter 45’ 56’ 62’ 70’HMC All motor controls included - 7 Lumber Decks Flat Chains 10’ 12’ 16’ 20’ 24’ 40’ 82’ 5 Chains WIDC All motor controls included - 2 Log Decks - 28’ Long 12’wide 3 chains stop loader - 14’ long 12’ wide 4 chains stop loader - All motor controls included - Newman Trimmer, drop saws, scrap belt chain 100’x 24’ - Unscrambler 16’wide x 5’high 8 chains - Air Compressor Model SSREP100 HP - Air Dryer storage tank - HMC Model mm10 4 heah block carriage 49’ - HMC Saw Booth - HMC Feed Works - HMC Husk 54’ bottom saw 36’ top saw - 200 HP motor - HMC Log Turner - HMC Drop Belt Live Off Barrer - 10 Headrig saws inserted tooth 54” - Roof Top Chain 10ft 5 Chain - Blower system - Tie-Cant Deck 62’Lx13’ W 4 chain all motors & Controls - Roof Top Lumber Deck 30’L x 13’W 5 chains all motors & Controls

Rosser head, slant track, hyd. drive on the head, in working condition, CALL FOR REBUILDING OPTIONS ON THIS MACHINE

rosser head style, all hyd. drive, 36" dia. log capacity x 12' long, very good condition

HMC Carriage 5x10 Cab with controls System is already removed from service and ready to load. Notes from seller: Carriage is 17'1" longKnee spacing is 63" from 1 to 2 78" from 2 to 3 1 to 3 is 141 1/4" Carriage frame is 76 1/2 " wide Track centers are 62" Track rails are worn out. We used the old track frame for our new carriage

HMC 3 Head Block Helle 2 or 3 Vert,Edger 16' Capacity Hyd. Over Air Set Infeed Log Deck Outfeed Deck 375HP J D Power Unit Removed From Service

HMC 3 Head Block Carriage

HMC Mdl 1 DC Carriage Drive w/ 75HP S/N 137-98

HMC MDS50 Drop Saw Trimmer s/n 076-00

rosserhead style, in working condition

HMC Line Bar Unit

2003 HMC AC40 2 Knee RH Carriage Circle Saw Mill, Cab controls, Rails, Husk

HMC AC40 Carriage (Sawmill) Rebuilt AC40 Board Dog Carriage, 4 head blocks, 42” opening, set shaft carriage. Factory rebuilt with new equipment warranty. Photos are reference only