HEESEMANN - KSA 8 CSD, ...Lacquer/Sealer Sander w/80" Belt WidthThis is a Very Special "extra wide" HEESEMANN equipped with: HEESEMANN's patented "CSD" selective pressure adjustment system, sensors placed every 5/8" (16 mm) sense part configuration; pressure for each segment can be preprogrammed to provide less pressure on the outer edges, or more in the center if desired. The "CSD" computer control will hold a max. of (20) programs.Equipped with: -- Segmented Polishing Platen: Segments are computer controlled to conform to irregular shaped panels; sanding pressure on panel edges is adjustable. -- Platen will accept panel thickness variation up to 5/64" (2 mm). -- Dual speed motor: 26 & 31 kW (35 & 42 HP); abrasive belt speed: 10 + 20 MPS (33 + 66 FPM); abrasive belt size: 2,050 mm x 3,250 mm (80.7" x 128"); pneumatic air tension and tracking control. -- 250 mm Dia. Rotary Panel Cleaning Brush, 5 HP motor, 150 mm Outfeed Rotary Panel Cleaning Brush, and 2 HP motor.Additional Features: -- Vacuum bed assembly to ensure flatness of parts and feeding of small parts. -- Computer control and monitor, light indication of panel movement; electronic abrasive belt tracking.Feed System: -- Variable feed speed from 5 - 15 MPM (16 - 49 FPM); 4 kW (5 HP) feed motor; motorized thickness opening.NOTE: This Sander had a "Brand New" ...$ 17,000 display/control installed shortly before it was taken out of service in 2016. The machine has been in storage since that time.

HEESEMANN MFA-8 D Wide Belt Sander (4) Heads; 53" Width cap. Veneer/ Sealer Sanding Wide Belt.Great Lacquer/Sealer sander with: (2) Segmented polishing platen, (2) Orbital heads, (1) De-nibbing/Polishing brush.Head Configuration: Head 1: Segmented polishing platen, 5/8 wide segments CSD Control, Variable speed abrasive belt with inverter RPM control, 15HP motorHead 2: Segmented polishing platen, 5/8 wide segments CSD Control, Variable speed abrasive belt with inverter RPM control, 15HP motorHead 3: Orbital head with composite/dense fiber loading; 5HP motorHead 4: Orbital head with composite/dense fiber loading: 5HP motor(1) Brush Type head for de- nibbing and polishingSpecifications: -- LCD monitor with graphic display and key pad entry, 20 program capacity, -- Pressure for each segment can be pre-programmed to provide less pressure on the outer edges or more in the center if required.Equipped with & Features -- Air blast abrasive belt cleaner on heads 1 & 2. -- Variable feed speed from 10 to 49 FPM via 2 HP feed drive. -- Motorized thickness opening 1/4" to 3-5/32" max. -- Rubber covered Infeed and out feed holddown rolls.

Heesemann MFA Impression 4-Head Wide Belt SanderSpecifications -- Working Width: 53" (1350mm) -- Workpiece Thickness: 0.118" to 6" (3mm to 160mm) -- Working Height: 36.2" (880 mm) -- Wide Belt Size: 103" x 55" (2620mm x 1400mm) -- Cross Belt Size: 189"x6" (4800 x 150mm) -- Variable Feed Speed: 10-50 FPM (3-15 mpm) -- Vacuum Bed for Safe Movement -- os Workpieces Shorter than 19.7" (500mm)Head Configuration1st Head: Cross Sanding Unit Heesemann's Cross Sanding Head Unit Removes Fiber from Solid Wood or can be used to Remove Tape from VeneerSanding Belt Speed:6.5 - 65 FPS (2-20 m/s)Drive Motor: 23HP (17kW)2nd Head: Longitudinal Sanding Unit Sanding Belt Speed: 6-60 FPS (1.8-18 m/s) Drive Motor: 23HP (17kW)3rd Head Longitudinal Sanding Unit Sanding Belt Speed: 6-60 FPS (1.8-18 m/s) Drive Motor: 23HP (17kW)4th Head: Lef Head w/ Internal Pressure Belt Enhanced Finish Let Head Features an Inner Chevron Belt to Allow for Fine Sanding of Workpiece Sanding Belt Speed w/o Pressure Belt: 6-60 FPS (1.8-18 m/s) Sanding Belt Speed w/ Pressure Belt: 6-30 FPS (1.8-9 m/s) Drive Motor: 23HP (17kW)Equipped with & Features --All Heads Variable Speed Belt equipped with Inverter Motor -- CSD® segmented pad system on all Heads -- A pinch roll system, rubber covered and adjustable -- An automatic infra-red belt control -- Servo cross belt tracking adjustments, for quick and easy belt centering when loading -- Workpiece Blasting Device -- Rotating Compressed Air Nozzles for Blasting Workpiece Surface -- LED Lights on Belt Change Side -- Ionization Bar from Above that Helps Reduce Static Charge -- Pneumatic Conveyor Belt Cleaning -- Dust Extraction: Approx 6000 CFM -- Compressed Air: 100 cfm @ 100 psi -- Power: 480 Volt, 3 Phase, 60HZ

Heesemann MFA6 (3) Head Wide Belt Sander, 53" width cap. Drum Drum, Segmented platenHead configuration1st Head: Steel contact roll, 30 HP motor2nd Head: Rubber covered contact roll, 20 HP motor3rd Head: Segmented polishing platen, electronically controlled segments to conform to panel size, 20 HP motor4th Station: Outfeed rotary panel cleaning brush, 2 HP motor.Specifications -- Platen head equipped with: HESSEMANN's Patented "CSD-32" selective pressure adjustment system; sensors placed every (32 mm) sense part configuration, pressure for each segment can be pre-programmed to provide less pressure on the outer edges or more in the center if desired. -- Both contact rolls with NC positioning and auto grit compensation, automatic line control for platen independent of feed speed determines automatically the correct part in time for the pressure segmentEquipped with & Features -- Outfeed rotary panel cleaning brush, 2 HP motor. -- 55" x 103" Abrasive belts on all heads with abrasive belt air cleaners, "ICP" control for all sander functions, (20) programs storrage. -- Variable feed speed from 10 - 49 FPM, 3 HP feed drive with inverter control. -- Vacuum conveyor bed assembly with suction fan and )motor mounted in machine base, motorized thickness opening 0" - 5-7/8" w/digital readout, constant passline of conveyor bed assembly 35" height.NOTE Some Spec's need to Varified

HEESEMANN - LSM 8-5 RRRL, ...53" Wide Belt Sander53" Width cap.: Drum, Drum, Drum, and CSD® Pad.Head Configuration:• Unit 1 - Longitudinal Sanding Unit: Steel contact roller, helically grooved. - Single-speed 48 HP motor, electronic braking.• Unit 2 - Longitudinal Sanding Unit: Rubber-covered contact roller, helically grooved. - Single-speed 35 HP motor, electronic braking.• Unit 3 - Longitudinal Sanding Unit:- Rubber-covered contact roller, helically grooved. - Single-speed 35 HP motor, electronic braking, bi-directional drive.• Unit 4 - Longitudinal Sanding Unit: CSD® Segmented pad system, 2-speed 20/26 HP motor, electronic braking.• Unit 5 - Panel Cleaning Brush: Fiber trimming, 2.3 HP Motor.Specifications: -- Working height: 880 mm (34.64"). -- Workpiece thickness: 3 mm to 150 mm (1/8" to 6"). -- Working width: 1,300 mm (51-1/8"). -- Longitudinal belt: 1,350 x 2,620 mm (53" x 103"). -- Machine voltage: U.S. Electrics 480 Volts, 3-Phase, 60 cycles.Constant Pass LineController: -- Industrial PC. -- TFT Color touchscreen. -- Windows® Operating System. -- (100) Memory addresses for: • CSD® sanding pressure. • Sanding start/stop. • Sanding belt speeds. • Grit sequence indication. • Sanding belt selection - "ON/OFF". • 1-Button sequenced starting for all motors.RS-232 Serial port.RJ-45 LAN Port.Modem with software licenses.For All additional, detailed specs, select the "View Literature" link .

HEESEMANN LSM-8/3-OSR Wide Belt Finishing Sander, 52" and (3) Heads; Equipped with: (1) longitudinal segmented platen head. and (2) Orbital Platens -- 1st Head: Longitudinal segmented platen head. Segmented Polishing Platen, 20 & 27 HP dual speed motor. electronically controlled segments to conform to panel size,.2620 x 1350 mm (91.4 x 53.2") Sanding belt. - Equipped with HEESEMANN's patented "CSD" selective pressure adjustment system, sensors placed every 16 mm (5/8") sense part configuration; pressure for each segment, to eliminate sand through, can be pre-programmed to provide less pressure on the outer edges or more in the center if desired. The "CSD" computer control will hold a maximum of (20) programs. -- 2nd & 3rd Heads: OSR Dual orbital action head with (1) high-speed orbit on sanding pad, powered by 3 kW (4.5 HP) motor.Secondary oscillation movement of platens powered by 1.5 HP motor. Upstream and downstream vacuum chutes on each head for dust localized dust pickup.- Platens feature "quick change" abrasive material; Both orbital heads with variable speed inverter drives. -- Outfeed Rotary Brush with cleaning brush loading with single end adjustment , 6" max. dia., 3.4 HP motor. -- Variable feed speed from 13 to 82 FPM, 6.5 HP feed drive. -- Infeed and outfeed Ssissor Lift and Control box shown are not included. -- Motorized thickness opening 1/4" to 3-5/32" max. - -- Power Consumption: 63 KW, 75 Amps. -- Separate display console for CSD control.

54" 3-Head Orbital Sander, For abrasive belt cross-grain scratch removal with (3) Orbital Platen Heads & (1) Rotary Brush Head Configuration: 1st, 2nd, & 3rd Heads: Each with 5" W Platen, Dual orbital action, High-speed orbit on sanding pad with 3 kW (4 HP) Motor, Secondary oscillation with 1-1/2 HP Motor, "Quick-change" abrasive material, Inverter drive; Rotary Brush: 6" Maximum diameter, 3-1/2 HP Motor, Brush loading, Ionization bar for final fine dust collection Vacuum conveyor bed with 10 HP Blower motor, Inverter-controlled variable speed drive with 4 HP Motor & Variable feed speeds 15 - 66 FPM, Automatic conveyor belt tracking, Automatic parts thickness, with 1/8" - 4-5/8" Thickness range & Programmable height adjustment, (4) Screw jacks PC-based control, Windows XP, Touchscreen monitor, Infeed & outfeed spring-loaded hold-down rolls, Infeed hand safety stop, outfeed emergency stop, Digital motor load meters, High-efficiency dust extraction NOTE: Machine is currently in storage.

HEIAN FP-151-MC-2113 5-Axis CNC MachineFor high speed & precision routing/trimming & sizing wood and composite parts.Equipped With: -- (2100 mm) x (1,300 mm), moving table, fixed bridge style machining center; mahogany vacuum table. -- 3.7 kW, NT 30 Type ATC spindle, variable speed from 2,000 - 18,000 RPM with 8-position tool carousel. -- FANUC "16i CNC Control, 10.4" LCD , RS-232C/PCMCIA (memory card). Features: -- 5-Axis simultaneous motion, M & G code programming, inch or metric operation. -- Working Axes Stroke & Speed: X-Axis (2,600 mm) 60 m/Min; Y-axis (1,600 mm) 40 m/Mn; Z-axis (800 mm) 20 m/Min -- C-axis +/- 270°; B-axis +/- 110°; C-axis travels at 4,000°/Min and B travels at 4,000°/Min. -- Complete with assorted tool holders.

HMC 2-Saw Trimmer Model ET-10,;Complete with the following features: --16′ capacity. --Push Button Setworks. --Left hand (feeds from left to right). --Cuts up to 8″ thick. --Belt Conveyor for waste.NOTE: Removed from service and it was running just fine at the time of removal. Stored outside.

HOCKER POLYTECHNIK - MULTISTAR Series, ...Pulse Jet Baghouse 33,000 CFM (56,000 M³/Hr) based on 5.2 to 1 Air-to-cloth ratio (FPM - average air velocity thru filter media) with 6,345 square feet of filter area. -- Filtration: Filters are automatically cleaned by Pulse-Jet system based on supply of 1" dia. dried clean compressed air line from Plant. Cleaning automatically controlled via timed cycles or by the Delta-P, which is the differential pressure across the filter bags. -- Supplied with: (4) HOCKER DER - 040/45022 radial BI fan; each directly driven by 30 HP - TEFC 3,600 RPM High Efficiency motors; mounted on the clean air side. Rated for a total of 33,000 CFM at 16" SP (4,000 Pa). Fan inlets are 18" (450 mm) dia. each. Non-return flap camper on the outlet side. -- Includes Electrical panel with: PLC Controls; Explosion Relief Panels; Sprinkler heads in the clean air plenum; ATEX approved construction with 11-gauge electroplated galvanized steel shell with clean air outlet not returned to plant. -- Equipped with: (1) HP Rotary Air Lock. -- Control - SIEMENS - SIMATIC TPI200: PLC Controller housed in a floor-mounted central control panel with modem module for allowing HOCKER online access to assist in program changes, 12" TFT color, touchscreen display.All starters and contacts for included motors.Pictorial guided navigation and fault messages are displayed in text.Graphic images, curves, bar diagrams, parameter adjustment settings, and fault report.FI MF 22.0 kW SPS Ctrl.: Allows startup of several fans, one after the other. -- VFD drives on each motor with: Automatic motor tuning, automatic startup, min./max. speed limits, DC brakes, and operating hours meter. -- Includes: Access ladder to upper catwalk and exterior pipe. Heavy-Duty galvanized for outdoor operation. -- Professional dismantling and transportation available upon request.

HOFER HOP 160 K Hydraulic Door/Veneer Heavy Duty Cold PressSpecifications:Platen size 63" deep x 98" long, Total Daylight/Opening 32".available. Currently set at about 13" opening. Top platen is hydraulically powered by a 2.2 KW power pack. and has (10 sets) of bolt holes for manual adjustment of daylight opening.Equipped with:(8) 3-1/4" Diameter Hydraulic cylinders, Rack & pinion platen leveling adjustment.Front and back loading (access on all sides).Heavy duty steel structural beams. Bolted top and bottom platens.Features:Pneumatically loaded 3 +1 rows of idle rollers on bottom platen for ease of feeding the load in and out front of press. Air valve for up/down selection of bottom platen rollers.Hydraulic closing speed adjustment.Electrical controls on right hand side.Dimensions/Weight: 124" x 72" x 122" H. Approx. 12,000 Lbs.

HOFFMANN PU 2 DOVETAIL ROUTER (SINGLE SPINDLE) Pneumatic Dovetail Routing Machine - Dovetail routing machine for use with HOFFMAN dovetail butterfly connectors. - Maximum routing height 4", Max. workpiece height 5-3/4" - Table size 15-1/2” x 27-1/2” x 36-1/2” H - Production speed: Approx. 16 SPM (2 Complete rectangular frames) - (1) HOFFMANN "UAD 33 F" 33,000 RPM 1,000 W Router motor - 45° Fence, Accurately positions material with guide in table keyway, Quick adjustments made by adjusting fence plate - Pneumatic hold-down, Pneumatic foot pedal Includes: - Extra HOFFMANN "UAD 33 F" 33,000 RPM 1000 W Router Motor - 2007 HOFFMANN "FM1000" 35,000 RPM 1,000 W Router Motor - (2) 16” x 48” x 35” H Left-Hand & Right-Hand Aluminum Frame Tables, with 3/4” Thick Top, & 2” x 2” Aluminum frame - Palletized Dimensions: 42” x 42” x 60” H

HOLYTEK SS-512 TS Shaper with Tilting Spindle, and Power FeederSpecifications: -- 1-1/4" Interchangeable spindle, 7.5 HP motor with (5) spindle speed settings of 3,000 - 4,000 - 6,000 - 8,000, & 10,000 RPM. -- Approx. 6" max. cap. under nut, 31" x 39" cast iron table. -- Insert ring diameters 2.8", 4/3", 6" and 8". -- Tilting spindle +10° and -45° -- Vertical movement of the spindle 7" -- sliding tableComplete with: -- Reverse rotation switch, adjustable fence assembly, and dust hood. -- 3-Roll Power Feeder

HOLYTEK - HRS-12TK, ...Straight Line Rip SawSpecifications: -- Overhead saw arbor, 15 HP motor belt driven, 4,500 RPM arbor. -- 12" Dia. max. saw blade. -- 3-3/8" Max. depth of cut. -- 18" Max. throat depth. -- 2 HP Stepped feed speeds of 50 - 65 - 83 - 100. -- Automatic lubrication of chain. -- Magnetic controls. -- Saw is glue line rated.Equipped with & Features: -- Overhead holddown rolls. -- Double-row of antikickback fingers. -- (6) Pressure rollers. -- Infeed adjustable fence line. -- Cast Iron table with rip fence.

Holytek 37DA Wide Belt Sander (2) Heads37" Width cap Drum, Combination Head1st Head: 7" Dia. spiral grooved rubber covered contact roller, 20 HP motor;2nd Head: Combination sanding head with 5" dia. spiral grooved rubber covered contact roll & 2" wide polishing platen, 15 HP motor.Specifications -- Abrasive belt size of 37" x 60" -- Pneumatic belt tensioning and electronic abrasive belt tracking -- 12" min. working length. -- 2 HP Conveyor belt motor, -- Variable feed speed from 13 - 52 FPM,Equipped with & Features -- Infeed & outfeed rubber covered holddown rolls; -- 0" - 4" motorized thickness adjustment by 0.5 HP motor. -- Safety stop bar, emergency rail stop across the front of conveyor -- Motor load meters.

HOLYTEK - HRS-12TK, ...Straight Line Rip SawSpecifications: -- Overhead saw arbor, 15 HP motor belt driven, 4,500 RPM arbor. -- 12" Dia. max. saw blade. -- 3-3/8" Max. depth of cut. -- 18" Max. throat depth. -- 2 HP Stepped feed speeds of 50 - 65 - 83 - 100. -- Automatic lubrication of chain. -- Magnetic controls. -- Saw is glue line rated.Equipped with & Features: -- Overhead holddown rolls. -- Double-row of antikickback fingers. -- (6) Pressure rollers. -- Infeed adjustable fence line. -- Cast Iron table with rip fence.

HOLYTEK GES 920 RK Wide Belt Sander(2) Heads drum and combination head -- (2) Head, 36" width cap., -- 1st Head: Heavy duty rubber covered contact drum, 15 HP motor; -- 2nd Head: Combination head with 6" dia. contact roll, 20 HP motor, -- 2 HP feed motor, 16 - 55 FPM variable feed speed, -- 37" x 75" abrasive belts, electronic oscillating belt system. -- Motorized table elevation with .25 HP motor, maximum height 125 mm (4.9")Equipped with: -- Digital read-out & infeed and outfeed spring loaded hold down rolls.

HOLYTEK - KL-36PC, ...2-Head Sander 2-Head Planer Sander 36" with planer head & combination head.Description: -- Planing Head (P): 6'' Dia. made of steel with spiral design for heavy stock removal. 228 TCT Tips: 15 x 15 x 2.5 mm; each disposed on (6) rows. Each knife has: (4) Usable cutting edges; easy access to planing head for tips rotation or replacement. -- Precise dial indicator showing the exact positioning of the sanding pad; quiet & smooth oscillation! Pneumatic oscillation system controlled electronically by an infrared system, which is not affected by dust. -- Combination Head: (1) Drum & (1) sanding pad (C) for superior quality of finishing. Sanding belt with: 120 or 150 Grit; allows finishing sanding in a single pass. -- Elevation Table: (4) Screws. -- Infeed roller table extension: 15-3/4". -- Outfeed roller table: 15-3/4" with (2) Rollers. -- Centralized Control Panel with: Electronic digital readout (Metric or Imperial) for elevation; precise positioning at the elevation requested. -- Ammeter indicating: Electrical intensity on the spiral cutterhead and the combination head motors. -- Electrical box with: CSA Approved electrical components ensuring maximum dependability and an outstanding long-lasting performance.Specifications -- Spiral cutterhead motor: 20 HP - 600 V; 60 Hz - 3 Ph. -- Combination head motor: 15 HP - 600 V; 60 Hz - 3 Ph. -- Table elevation motor: 1/4 HP - 600 V; 60 Hz - 3 Ph. -- Feed motor: 2 HP - 600 V; 60 Hz - 3 Ph. -- Spiral cutterhead dia.: 6''. -- TCT Tips dim.: 15 x 15 x 2 mm (228); (6) rows. -- Max. working width: 36". -- Min. working length: 12". -- Max. working thickness: 5". -- Sanding belt dim.: 37" x 75". -- Dust hoods dia.: 4'' x 2 & 5" x 2. -- Machine dim.: 71" L x 76" W x 77'' H. -- Net weight: 1,450 kG or 3,190 Lbs.

HOLYTEK HP-11P Horizontal Resaw -- Hydraulic Feeding conveyor, hydraulic pump with 3 HP motor -- Main saw motor 20 hp. Specifications: -- Working width capacity 12“ (300 mm) -- Variable Feed Speed 0- 17 m/min (0 to 55 FPM) -- Thickness capacity 4mm to 125 mm (.11/8" to 4.92") -- Conveyor tilting 0 ° to 7° -- Electroni display of cutting height -- Blade Capacity 4270 X 25 X 0.89 mm. -- Wheels Diameter 725 mm -- Return conveyor on machine top

HOLYTEK MHB 242 Top/Bottom Wide Belt SanderHeavy-duty and powerful double surface sander providing significant time saving and improved productivity.Smooth and quiet oscillation. Belts oscillation controlled electronically by an infrared system which resists dust.Pneumatic sanding belts tensioning ensuring fast and easy belt replacement.Independent motor for each sanding belt.Pneumatic disc brake system automatically activated if power supply is interrupted, thus preserving the sanding belts from being damaged. Top and bottom 24" wide belt sanderFeatures: -- Spiral grooved 8" (D) rollers (R) and 3-1/2" (D) rollers (K) keep the sanding belts cool. -- Sanding belts: 75" Long. -- Elevation of table with digital readout and activated by independent motor. -- Control panel with: Ammeters indicating main motors current. Specifications: -- Upper Drum motor: 15 HP; 600 V; 60 Hz - 3-Ph. -- Upper Combination head motor: 10 HP; 600 V; 60 Hz - 3-Ph. -- Lower Drum motor: 15 HP; 600 V; 60 Hz - 3-Ph. -- Lower Combination head motor: 10 HP, 600 V, 60 Hz - 3-Ph. -- Feeding motors: 2 HP (x2). -- Table elevation motor: 0.5 HP. -- Electrical intensity: 53 A. -- Drums: 8" (D) - 75 DUROS. -- Max. working width: 24". -- Min. working length: 13-3/4". -- Working thickness: 3/16" ~ 5" -- Sanding belts dimensions: 25" x 75". -- Variable feeding speed: 8 - 16 MPM. -- Dust hoods Top: 4 x 4"(D); Bottom: 3 x 4"(D). -- OAL 127" x 70" x 75" high. -- Weight: 9,460 Lbs.