COSTA K6 WCCT 1350 4-Head Planer / Sander 4-Head with Planer, Drum, Drum and Combination headSpecifications: -- Front head #1 54" Helical planer head with (480) insert knives 34 kW or 45 HP motor. this is a removable head complete with cart for cleaning and changing knives. -- Head #2 Drum currently set up with 100 grit abrasive sanding belt 22 kW or 30 HP motor., -- Head # 3 Drum with 150 grit abrasive sanding belt 17 kW or 22 HP motor. -- Head # 4 Combi head with timed air bladder platen, currently runs 180 grit abrasive sanding belt, 14 kW or 20 HP motor. -- Feed mat speed from 4 - 20 feet per minute. Features: -- Capable of planning off 1/8" and sanding to 180 grit in one pass. -- Uses 52 - 54" x 103 abrasive sanding belts. -- Vacuum feed mat only surfaced 2 or 3 times, PLENTY of life left in it. -- Used in small shop running no more than 5 -10 hours a week, on a machine designed to run 3 shifts. -- Features Air scrubber unit on the out feed to remove any additional dust. Note: Machine was purchased New in February 2016

--This machine is in Auction @ https://exfactoryauctions.com/Detail/FD-230117/event/A122024$1. --Low starting bid! Equipped with: 1st & 2nd Heads: Each with 2” W Cross brush belts, 2.5 kW (3.35 HP) - 1,690 RPM Motor, Rotating belt on vertical axis supports series of pads with abrasive paper, Pads are adjustable to vary angle of contact on panel during rotation of belt, Pads with abrasive strip makes contact with workpieces from both sides as it rotates. (3) 2” Dia. Rubberized hold-down rolls, (1) before and after each cross brush belt head. 3rd & 4th Heads: Each with 62” L x 16” Dia. Brush Roll & 2.5 kW (3.35 HP) - 1,140 RPM Motor, & Horizontal angle adjustment. 2-5/8” dia x 7/8” w swivel rubber wheels before each brush roll head. (1) 2” Dia. Rubberized hold-down roll after last brush roll head. 53-1/2” W x 12’ L Vacuum feed belt, with 2.64 kW (3-1/2 HP) - 1,695 RPM Motor, Holes on 1-1/2” W & 2” L Centers, 2-1/2” Dia. Rubber-covered infeed & outfeed rolls, Motorized adjustment with Digital readout with LED Display. Control motor load meters. Complete with: Instruction Manual.

COSTA K7 CCCT 650 ... 4-Head Wide Belt Sander, working width 650 mm (25.6") and constant pass line conveyor heightExcellent Veneer and Solid wood sander with (3) Contact rollers and (1) platen.Head Configuration: -- 1st Head: Steel contact roller, 250 mm (9-7/8") diameter, driven by 37 kW (50 HP) motor. Abrasive belt speed 24 m/Sec (78 FPS). -- 2nd Head: Rubber covered contact roller, 250 mm (9-7/8") diameter. Shore hardness 70. Driven by 30 kW (40 HP) motor. Abrasive belt speed 18 m/Sec (59 FPS). -- 3nd Head: Rubber covered contact roller, 250 mm (9-7/8") diameter. Shore hardness 70. Driven by 22 kW (30 HP) motor. Abrasive belt speed 18 m/Sec (59 FPS). -- 3rd Head: Segmented finishing platen, electronically controlled narrow segments conform to panel width and length for thin veneer sanding. Driven by 11 kW (15 HP) motor. Abrasive belt speed infinitely variable 3 - 16 m/Sec (30 - 52 FPS). -- Sanding Belt Info: abrasive belts, air blast abrasive belt cleaning, pneumatic belt tensioning with electronic tracking on all heads. Grit set system for abrasive belt grit compensation. -- At Outfeed: Brush Roller 180 mm (7") driven by 1.1 kW (1.5 HP) motor. Equipped with: -- PLC processor controls with touch screen. Integrated control cabinet. -- Feed System & Conveyor Bed: Min/max. working height 3 - 160 mm (1/8" - 6-5/16"). Variable feed speed conveyor with inverter control 4 - 20 m/Min (13 - 65 FPM). Constant Pass Line at 920 mm from floor (36"). Vacuum conveyor bed assembly. Infeed & outfeed spring loaded hold down shoes on all heads. Powered raise & lower of conveyor bed with LED readout.Also inculed: about $15,000 of sanding belt

Costa 60CT2-1150 (2)-Head, Wide Belt Sander44" width cap Drum, Combination HeadHead Co figuration 1st Head: Rubber-covered contact roll, 20 HP motor;2nd Head: Segmented polishing platen, (30) narrow segments are electronically controlled to conform to the panel shape and size to minimize veneer sand-throughs, each segment with variable pressure control, 15 HP motor.Specifications: -- Adjustable contact roll for varying thickness of abrasive belts with -- 45" x 103" Abrasive belt, electronic tracking. -- Motorized part thicknessopening on conveyor bed with digital readout, -- Variable feed speed 10 - 50 FPM with inverter drive, -- Vacuum conveyor bed assembly with 4 HP suction fan,infeed & outfeed spring loaded holddown rolls.Equipped with & Features: -- Controls mounted on the front of the machine, -- Instant shut-down safety guard, all motors with Y-Delta starters, and motor load meters.NOTE: Some spec's need to be verified

CP CD1000 CAN DENSIFIER -- 900 to 1,500 Lbs/Hr capacity -- Fully automatic solid-state Controller -- Density: 40 Lbs per cu. ft. allowing 140,000 Lbs in 50' railcars or 40,000 Lbs in 40' Trailers. -- 10 HP - 3/60/208/230/460 Volt Hydraulic Power Unit

CP MANUFACTURING - S100-6-LH-US, ...Screens -- (1) System of (2) Screens -- Very lght Use -- Ordered as part of a Single-Stream Sort System that was designed to run 10 Tons/Hr -- 1-Feed Conveyor -- Each: 14,500 Lbs -- Loaded onto your Truck

CAN-PAK - CD-3000: Complete Can Densifier -- Motor: 25 HP.Dimensions• Height: 9’-2";.• Width: 3’-10";.• Length: 13’-5";.• Machine weight: 8,000 Lbs.• Conveyor weight: 1,000 Lbs.• Conveyor: 11’-5"; High x 20-1/2"; wide x 13’ long.Specifications• 25 HP Power unit.• 460 Volt, 3-phase wiring.• Solid-state programmable controller.• Thermostatically controlled hydraulic oil cooler.• 1 Cubic yard hopper.• 120-gallon hydraulic tank.• 20-1/2"; Wide infeed conveyor with: 3/4 HP Motor. Direct drive gear reducer. Magnetic head pulley. Steel reject chute.

CP100 Can Flattener --220V, 1200 lbs per hour --Infeed Conveyor --Magnetic Separator -- New belt included

CRAFTSMAN DP-65 Drill PressSpecifications: -- Capacity: 15" -- Motor: 0.33 HP Equipped with: -- Push button control -- Stand

CRAM-A-LOT - SCR-T2-34: ...34-Yard Self-Contained CompactorsSpecifications: -- Cylinder: (2) 4". -- Main motor: 10 HP. -- Feed opening: 41″ x 58″ (1,041 mm x 1,473 mm). -- Capacity: 34-Yard. -- Ram force: Up to 24 tons.

CRAM-A-LOT - HX-60: Closed Door Baler with Cart Dumper & Infeed ConveyorSpecifications: --The CRAM-A-LOT "HX-60 HH" & "HX" Series Balers are ideal for warehouses and designed for ease of installation, operation, and maintenance. -- CRAM-A-LOT® HH & HX Series Balers are: Built with extra Heavy-Duty construction; ideal for warehouses & recyclers who deal with large quantities of corrugated and paper products.Baler is designed for long hours of operation and can operate either manually or automatically with photocell control. Optional custom-engineered Feed Conveyors and Cart Dumper Systems efficiently control Baler feed rates for optimum performance in a complete Baling System.Standard Features include:ANSI Z245.5 Compliant: All Compactors meet or exceed ANSI Z245.5 safety standards.UL/CUL Listed Control Panels.UHMW Ram Shoes: Adjustable to assure straight tracking and readily replaceable, should the need arise.Oil Sight Gauge: Oil level at a glance.Oil Filter: Replaceable "spin-on" cartridge to keep your oil clean.Heavy-Duty Controls: NEMA 4-Rated pushbutton controls with "key lockable" start switch.Automatic single-cycle operation. -- Bale Size: 60" x 30" x 40". -- Bale Weight: Up to (OCC) 1,400 Lbs. --Throughput: (OCC) 2-1/2 Bales /Hr. -- Cylinder: 7".

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6k ROCKWELL/CRESCENT 5-Head Single Head Tenoner Equipped with: Manually-operated sliding table. (1) Top & (1) Bottom Tenon Heads, Each with 2 HP Motor, (1) Top & (1) Bottom Cope Heads, Each with 1 HP Motor, & (1) 7" Cutoff head with 1 HP Motor.

CROUCH - 81-70 ...Edge Sander (Non-Oscillating)5 HP Direct drive motor; 6" x 144" abrasive belt size; (1) 8" x 56" Platen.Equipped with: -- (1) 12" x 56" Adjustable side table and (1) 15" x 28" end table.Tables adjust vertically 5" and laterally 2-1/2". -- 8" Dia. rubber covered drive pulley and 4" dia. aluminum idle pulley.

CROWN RC3020-30 Stand-Up ForkliftSpecifications: Load Capacity: 3,000 Lbs -- 3-stage mast -- Max. lift height 190" -- Clearance height: 89" lowered -- Battery drive train: 24VEquipped with: -- Side shift -- cushion tires -- Overhead guard -- Power steering and SCR travel controllerNOTE: Order Picker is not running, Battery is charged, needs wiring harness

CSMI Hi-Tech Optimized Board Edger. Complete with the following features: -- Two-saw Edger. --Top reman Head and System. --Infeed. --Unscrambler. --Scanning and Optimization. NOTE: Offered earlier at $75,000.

CUMMINS - 682-FDR-036JJW, ...1000K DIESEL GENERATORSpecifications: -- Output: 480/277 / 3-Phase -- 1,000 kW -- 1,250 KVA -- 1,504 Amps -- 1,800 RPMNOTE: (299) Hours on meter in factory-built enclosure. - Available for inspection!

Custom Built Disc Scalper;Includes the following features: --3 Ft. Wide X 10 FT. Long. --Fitted with 9 Rows of Discs, shaft mounted. --Drive Chain connected Row-to-Row. --Motor Platform (no motor or reducer). --Mounted onto a Steel Frame. --Bottom and End Discharge.

D M C FINESAND 130 2PO WIDE BELT (50" - 90", 2-HEAD): -- Specifications:Orbital Pad Sander, designed for cross-grain scratch removal on style & rail frames; with (2) Orbital Platens & (1) Brush. -- Working Capacity: Width 51", height/opening 1/8" - 4-5/8", motorized part thickness adjustment with digital readout, (4) screw jacks rise & fall. -- Sanding Heads: (2) 10" Wide Platen heads with rubber surface for elimination of abrasive belt cross-grain scratches. Dual orbital action heads with (1) high speed orbit on sanding pad, powered by 5.5 HP motor, and a secondary "low RPM" orbit on head assembly (1.5 HP motor), superimposed over the high-speed orbit for fast cutting action. -- Rotating Cleaning brush on outfeed side. Abrasive material for Sanding Heads is 18" x 52" in size. -- Feed Conveyor: Variable feed speed from 6 - 40 FPM, inverter controlled by 5.5 HP motor; vacuum conveyor bed with 15 HP blower motor. -- Complete With: - Digital height readout. - Infeed and outfeed rubber coated hold-down rolls. - Infeed hand safety stop bar, emergency e-stop. - Star-Delta motor starter. - (2) Dial indicator motor load meters.

DMC UNISAND K 1100 Wide belt sander4-Head, 43" (1,100 mm) max. width cap. Head sequence: (3) Contact rolls and (1) Combi with roller and segmented platen.Heads configuration: -- 1st Head: Helical grooved steel contact roll, 10" dia., 48 HP motor. -- 2nd Head: Helically grooved rubber covered contact roll, 12-1/2" dia. and 65-Shore covering hardness, 35 HP motor. -- 3rd Head: Helically grooved rubber covered contact roll, 12-1/2" dia. 45-Shore covering hardness, 30 HP motor. -- 4th Head: Combi head with roller covered with rubber, 30 shore and Finishing sanding pad unit , 30 HP 2-speed motor with segmented pads pneumatically controlled -- All heads use 44" x 103" (to be confirmed) abrasive belts and are equipped with electronic tracking, automatic tensioning, automatic emergency breaking, and oscillating sanding belt cleaners.Controls: -- "HYDRA V-PAD" 10" Touch-screen computer for setup functions, color LCD Display, allows operator to setup/recall part thickness, -- Conveyor feed speed (3.5 - 18 MPM), -- Abrasive belt direction, and reversible speed setting of 4th head. -- Conveyor belt feed with inverter control, feed speeds from 11 - 60 FPM, 5.5 HP feed drive; -- Infeed & outfeed holddown pinch rolls on all heads, automatic part thickness setup with the moving feed belt, -- 2-speed motorized part thickness adjustment, 1/8" - 6" max. opening; -- Infeed & outfeed motorized conveyor extension rollers, automatic part thickness setup sensor. Complete with: -- Safety stop at infeed, -- Anti-kickback device, -- Infeed & outfeed emergency stops, -- Motor load meters, i -- Infeed & outfeed idle rollers, -- High efficiency dust extraction, and control console with monitor.Note: (spare parts not installed) New feed belt , new front pressure roller, new front pressure bar and several new small parts for approx $15,000 of value +11 boxes (approx 5 belts/ box) sanding belts 100 grit, 120 grit, 180 grit and 220 grit.

SCM DMC 90 RCS 135 2 Head 53 inch Wide Belt Sander 53" Width cap, Steel Drum, Combination HeadHead configuration1st Head: Steel Drum 36 HP Motor, 9" Diameter 2nd Head: Combination head 65 shore drum and solid wood platen, 30 HP Motor, 7" Dia. drumSpecifications: -- 54" x 103" Abrasive belts with electronic tracking. -- Shoe & Roller Holddowns. -- "Hydra 35" Computer controlled; set-up functions with a keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM; 6.4 HP feed drive. -- Vacuum conveyor bed with 7.5 HP Motor and suction fan. -- Automatic conveyor belt tensioning & tracking. -- Motorized part thickness opening with LED Readout; 1/8" - 4" max. opening; automatic part thickness set-up sensor. Equipped with & Features: -- Infeed safety stop, outfeed emergency stop, -- Motor load meters. -- 2-Roll infeed conveyor extension; -- High-efficiency dust extraction.NOTE: Specs have to be verified