INDUSTRIAL IWS 10 Finger Jointer:Shaper unit will handle material 2" to 8" wide, 5/8" to 2" thick and 5" minimum length and 30" maximum length.Equipped with: -- ( 2) Trim saws with 5 HP motors, (2) Scoring saws with 3 HP motors and (2) Shaper spindles with 15 HP motors - 1-13/16" dia.. -- Feed speeds from 0 to 150 FPM. Average speed of (100) lugs per minute; feed chain is equipped with lugs on 9" spacing. -- Glue applicator with improved glue spreading and simplified pump. -- Model 3502 90° brush transfer to the assembly and Flying Cut Off Saw. -- MOD - Assembly Press, 16' long, with (1) retrim saw, air over hydraulic clamp & squeezing including Complete with: -- Wertern/Nielson 800 FJ cutterhead grinder -- Set up stand -- (15) cutterhead -- Some spare parts

INDUSTRIAL - 3870 & 3550, ...Finger Jointer Medium Production2" x 8" Finger Jointer and 3550 Press with: (3) Saws. -- "3870" Right & left Shaper Section, left-hand discharge. -- Shaper cap.: 1/2" - 2" Thickness; 1-1/2" - 8" width (8" with lugs on 12" centers); 5-1/2" - 48" max. material length. Equipped with: -- NO Scoring saws; (3) 7.5 HP trim saws w/built-in adjustable length trim. -- (2) 20 HP Shaper motors. -- INDUSTRIAL Short block chain with: Lugs on 9" centers. -- Electronic variable feed drive: 10 - 60 FPM, 10 HP Feed drive. -- Automatic chain lubrication system; overhead air bag holddown. -- APQUIP Glue Applicator with: Glue pot; 90° lateral transfer system into the Assembly Press. -- Model "3550" Assembly Press: 16' Max. cutoff cap.; automatic cycling; PLC controlled feed speed varies automatically depending on part and cutoff lengths; 50 to 200 FPM.Powered Infeed flat top Chain with: New side alignment rolls to the retard section. -- Pieces advance through the Cutoff Saw to a movable limit switch and are cut-to-length; bottom mounted 5 HP Flying Cutoff Saw for continuous nonstop assembly. The cut-to-length piece drops down into a final squeeze chamber while the next piece is cut-to-length. Finished lengths are pushed out by the next piece onto material outfeed arms

INDUSTRIAL RESOURCES PASS ONE Pallet DismantlerRemove stringers with a single stroke and dismantle 400 plus pallets per shift with "one" operator. -- Machine size; 14' L x 5' W, table size 54" L x 60" W. Stringer cap. 54". -- Includes; Hydraulic power pack, 7.5 HP, 12 GPM @ 750 psi. Manual variable speed valving. Hydraulic cylinder 2" bore x 62" stroke. -- Options Include; Upper arm lift to provide ease of maintenance, greater flexibility, table rollers to help simplify pallet handling and 60" pallet length. -- Cycle time in / out approx. 7 Sec.

INGERSOLL-RAND UP6-15C-125 15 HP Single-Stage Horizontal Tank-Mounted Rotary Screw Air Compressor, with 2,313 Hrs. (as of 2/16/24) Specifications: Cap. 55 CFM, Max. pressure 125 PSI. Pump speed 6,250 RPM. Sound level 69 dBA. Equipped with: High efficiency close coupled air end. Motor shaft-mounted centrifugal blower. Electronic stepper motor inlet air control. 2-Stage Air-cooled aftercooler. Total positive lubrication system, with Spin-on filter. Compartmentalized sound enclosure. Complete with: 80 Gallon Cap. 24” Dia. x 33” L Horizontal Air Receiving Tank. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

INGERSOLL RAND D144IN 85 CFM Non-Cycling Refrigerated Compressed Air Dryer Specifications: Cap. 85 CFM. Max. working pressure 203 PSI. Max. inlet temperature 60° C (140° F). Refrigerant type R-134A. Equipped with: Aluminum braze plate heat exchanger. Variable speed fan. Microprocessor control, with Graphic display, LED Dew point indicator, Energy saving mode, & History of last (10) alarms. Remote alarm signal terminal. High pressure switch. Fully-adjustable programmable electronic drain valve. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

INGERSOLL RAND SSR-EP30SE Rotary Screw CompressorSpecifications: -- 30 HP Motor, approx. 120 CFM @ 125 PSI, totally integrated package, single stage rotary screw air end, max. modulate pressure 128 PSI; full sound enclosure keeps noise levels below 75 dBA.Features: -- "Intellisys" Microprocessor based control system, premium instrument panel, air-to-air 2-stage after-cooler, electronic stepper motor inlet air control, sealed SSR direct drive gear train, total positive lubrication system with spin-on filter.Control system includes: -- Finger touch membrane panel, LED diagnostic readout with (8) operating conditions, (12) programmable operating parameters, (4) fault warnings, and (11) fault shutdowns.(23,069) Total operating hours.

INGERSOLL RAND 5 HP Compressor, 17.1 CFM @ 90 PSI, 80-gal. Vertical Tank.Designed with: 2-Stage (2) cylinder cast iron pump, splash lubricated, inter-cooler, after-cooler, large dia. pressure gauge and air filter. -- Features: -- Ingersoll's T-30 series pump with high performance, proven design and dependable. -- Complete with: -- Tank mounted starter, automatic tank drain, heavy pressure switch, low oil switch, oil level sight-glass and fully covered belt guard; durable painted finish, service-and-operators manual. -- Also includes: -- Ingersoll-Rand refrigerated air dryer "DS35" with max. inlet temp of 140°F, Outlet Temp. 34°F - 40°F pressure dew point, 35 CFM, max. pressure PSIG 232 & 1/2" NPT air connection.

INGERSOLL RAND D144IN 85 CFM Non-Cycling Refrigerated Compressed Air DryerSpecifications: -- Cap. 85 CFM. -- Max. working pressure 203 PSI. -- Max. inlet temperature 60° C (140° F). -- Refrigerant type R-134A.Equipped with: -- Aluminum braze plate heat exchanger. -- Variable speed fan. -- Microprocessor control, with Graphic display, LED Dew point indicator, Energy saving mode, & History of last (10) alarms. -- Remote alarm signal terminal. -- High pressure switch. -- Fully-adjustable programmable electronic drain valve.

Ingersoll Rand RS37i,50hp Premium Rotary Screw Air Compressor --231 CFM, 3 Phase. --Includes Dryer(12,895) Total operating hours.

INTERNATIONAL - IB-4430-60-HD, ...Automatic Tie Horizontal BalerSpecifications: -- Bale size: 44" x 30" -- Hopper opening: 42" x 60" -- Cylinder bore: 8" -- Cylinder stroke: 82" -- Tension cylinder: 6" -- Cycle time: 15 Sec (no load) -- Ram force: 150,800 Lbs -- Main motor: 40 HPEquipped with: -- Oil cooler

INTERNATIONAL - MT-4843, ...Manual-Tie Horizontal Baler with Infeed ConveyorSpecifications: -- Cylinder: 8". -- Opening size: 60" x 46". -- Main motor: 40 HP.Equipped with: -- Control panel. -- Oil Cooler – Air-Over-Oil. -- 10' Bale Run-Out Table. -- High-Temp/Low Oil Level Shutdown. -- 48" x 43" x 60" Bale Size.

INTERNATIONAL - 1295-44, ...Horizontal Closed Door BalerSpecifications: -- Cylinder: 7" -- Feed opening: 42" x 50" -- Main motor: 30 HP

INTERNATIONAL - 1295-44, ...Horizontal Closed Door BalerSpecifications: -- Cylinder: 7" -- Feed opening: 42" x 50" -- Main motor: 30 HP

IBC - NA-1296A-48: Horizontal Closed-Door Baler Model -- 50 HP Motor. -- Main Cylinder: 10″. -- Bale Size: 30″ x 45″ x 60″. -- Hopper Size: 57″ L x 45″ W. -- Platen Pressure: 134 PSI. -- System Pressure: 3,000 PSI. -- Total Force: 235,620 Lbs. -- New cylinder installed approximately (6) months ago.

IBC - "IBC 4343 X 8 – 50 - 63": Horizontal Auto-Tie Baler -- Model: AT-4343-8-50-63. -- Type: Auto-Tie Baler. -- Motor: 50 HP. -- Cylinder Bore: 8";. -- Bale Size: 43"; x 43"; x Variable. -- Manufacturing Date: 2009.

INTERNATIONAL - NA-1295HD, ...Closed Door Horizontal BalerSpecifications: -- Bale size: 72" x 44" x 36" -- Main cylinder bore: 8" -- Total force: 113,000 Lbs -- Ram face pressure: 71 PSI -- Feed opening: 42" x 50" -- Cycle time: 30 sec -- Main motor: 30 HPFeatures: -- PLC Control -- Bale table -- Shear bar -- Heavy-duty welded construction -- Heavy-duty hydraulic system -- Easy-to-operate controls

INTERWOOD C-4010 CASE CLAMP: -- Specifications:Single-Bay pneumatic Clamp with: 108" Long x 60" high x 27" deep clamping cap. -- Equipped with:Movable; vertically positioned clamping beam with (2) adjustable horizontal clamps; (3) adjustable vertical clamps.Horizontal & vertical clamps with: (2) Pneumatic cylinders ea. for a total of (10) pressure cylinders with 2-3/4" stroke. -- Complete with:Built-in Horizontal/Vertical controls with pressure gauges.700 Lbs/Cylinder pressure at 100 PSI compressed air.

INTOREX HB-65 Automatic Dowel Milling Machine. For round dowels, table legs, broom handles, agricultural tool handles (concentric), umbrellas, stair rails, etc.Specifications: -- Automatic machine for rounding square stock with a cutter head that has (3) tools and finished diameters between 15 and 65 mm (3/32" to 2-1/2"). Unlimited working length. -- The head drive is 8.5 KW (10 HP). -- Working advance speed adjustable between 8 and 30 meters/Min. (26.25 to 98.5 FPM.) by means of a potentiometer. -- The machine has (4) draw-in rollers and (4) draw-out rollers to guarantee the uniform advance of the bar and good finish quality. -- INTOREX is designed and quality-built in Spain. -- Dimensions: 1500 mm (59.1" long x 1200 (47.3") wide x 1400 ( 55.2") high. Approx weight 850 Kg (1870 Lbs).

INTOREX TX-1300 Hydraulic Copy Lathe Hopper Feed. Overall Specs: -- Full automatic, equipped with (2) hydraulic copiers, (2) tool holder units, (2) back knives, Hopper Feed, Automatic Loading System. and electronic PLC control. Carriage runs on ball screw and tempered/ground guides. -- 1,600 mm (63") Max. between centers; hopper loading capacity of 140 x 140 mm (5.5" sq.) in automatic cycle and 210 mm (8.3") diameter in semi-automatice cycle. -- 10 HP Main motor with a variable speed of 730 - 5100 RPM; 3 HP hydraulic power pack. _ Fitted with PLC programmed logic to assist in setup; All working units (advance carriage, tailstock, tool holder units, etc) are hydraulically powered with independently adjustable speeds. -- Copying system with (2) hydraulic copier knives and traveling steady rest; includes a pre-rounding knife in front of steady; hydraulically powered back knives for doweling or plugging with form tools. -- Includes: Tooling, front safety guard; front mounted electrical panel with easy access to all pushbuttons and controls, and LED RPM display.

IPS - AT-752-50, ...Horizontal Auto-Tie BalerSpecifications: -- Charge box opening: 41" x 50" -- Main cylinder bore: 7" -- System pressure: 3,000 PSI -- Total force: 115,400 Lbs -- Ram face pressure: 63 PSI -- Tension cylinder bore: 6" -- Main motor: 50 HP -- Bale size: 43 x 43" x Variable length -- Bale weight: Up to 1,525 Lbs -- Bale volume: 66 Cu/Ft -- Cycle time: 20 SecFeatures: -- Hopper access door with safety interlock -- Oil Cooler