VIET S1 223 2620 1350 mm (53.15") 2-Head Wide Belt Sander, with Combination HeadSpecifications: -- For wood, veneer, & sealing. -- Thickness cap. 3 mm - 160 mm (0.12" - 6.30"). -- Variable feed speeds 3 - 16 MPM (10 - 52 FPM).Equipped with: -- 1st Head: Grooved rubber-covered steel contact roll, 25 HP Motor with Brake & Inverter, Quick set abrasive thickness setting, Electro-pneumatic "on/off" movement. -- 2nd Head: "KOMBI KRT" Combination head, with Grooved rubber-covered steel contact roll, Electro-pneumatic "On/Off" movement, Electronic segmented platen with 42-Section Reading beam at infeed, & 15 HP Motor with Brake & Inverter. -- Segmented rubber infeed hold-down roll, Segmented rubber hold-down roll between heads, & Segmented rubber outfeed hold-down roll. -- 1,380 mm x 2,620 mm (54.33" x 103.15") Abrasive belts. -- 54"; W Vacuum feed belt, 2 HP Feed motor with Inverter, 4-Roll Infeed & outfeed extensions, & 3 HP Blower. -- Control, with Touchpad, LCD Display, & (2) Motor load meters.EQUIPMENT NOTE: Seller states belt sensor is faulty and needs to be replaced and contact rolls have some wear spots. Potential buyers are welcome to inspect under power.

VIRUTEX - EB 25: Hot Air EdgebanderFor preglued PVC, veneer and melamine laminate coil stock; 0.4 - 1.0 mm edge thickness; up to 65 mm panel thickness cap.; automatic coil & single edge strip feed.Equipped with: -- Thermostatically controlled hot air blower; 3,300 Watts for up to 500° C temperature; (2 - 3) Min heat up time. -- Guillotine type front & rear end trim (with fast speed, flying knife); top & bottom flush trims with single motor drive to cutterheads. -- Overhead belt type feeder; 15 FPM feed speed. -- Mounted on machine base with panel support table.Includes: Used tooling on the machine.

VITAP ALFA 21 CONSTRUCTION/LINE BORER21-Spindle boring head on 32 mm centers. -- Specifications: drills vertically from bottom up and head rotates to horizontal position for edge boring, head rotation is pneumatic with switch control. -- 2-3/4" Max. drilling depth, 2.5 HP - 2,800 RPM motor, pneumatic drill head advance with speed control; head height adjustment with mechanical digital readout; 34" x 20" table size, max. workpiece width 31-1/2". -- Equipped with: Left & right side fences for construction boring, (2) pneumatic holddown clamps, line boring fence w/flip stops, pneumatic foot pedal control, magnetic starter & overload protection, and (1) set of quick-change chucks.

VITAP BLITZ CNC BORE, GLUE & DOWEL INSERTER: -- Specifications:(1) CNC Controlled head assembly with rapid (side-to-side) traverse, assembly with boring, gluing & insertion unit, This Flexible machine is IDEAL for JIT or high production runs. -- Working Area:Useable working area "X" axis 36.2" (920 mm), "Y" axis 3.14" (80 mm), "Z" axis up to 1.57" (40 mm) material thickness with digital readouts -- BG & D Unit(1) 1 HP - 6,000 RPM horizontal drill motor; 0.47" (12 mm) Maximum drill bit dia. (1) Glue injector & (1) dowel Inserter with 1.57" (40 mm) Max. dowel lengthMachine is capable of processing dowel diameters from 6 mm dia x 25 mm long - 10 mm dia x 40 mm long dowels (currently setup for 8 mm dia dowels); -- Operator & Machine Control:CNC "Color Touch-Screen" Controller for function & simple part programming and program storage. -- Complete with: (1) 12" Dia. vibratory feed hopper, totally sealed electronically metered glue system with "Automatic" injector flushing; (1) 4.75 G (18 L) Glue tank & (1) 2.37 G (9 L) water tank;(4) Inclined vertical pneumatic hold-down clamps; Function selector control for boring only or doweling; Anti-slip table surface, Rack & pinion drive and centralized dust collection manifold.

VITAP - BLITZ: CNC Bore, Glue & Dowel Inserter -- Specifications(1) CNC Controlled head assembly with: Rapid (side-to-side) traverse; assembly with boring, gluing & insertion unit This "flexible" machine is IDEAL for JIT or high production runs. -- Working AreaUsable working area: "X" Axis 36.2" (920 mm); "Y" axis 3.14" (80 mm); "Z" axis up to 1.57" (40 mm) material thickness with digital readouts. -- BGD Unit(1) 1 HP - 6,000 RPM Horizontal drill motor; 0.47" (12 mm) max. drill bit dia.; (1) glue injector & (1) dowel Inserter with: 1.57" (40 mm) Max. dowel length.Machine capable of processing dowel diameters from: 6 mm Dia. x 25 mm long - 10 mm dia. x 40 mm long dowels (currently setup for 8 mm dia. dowels). -- Operator InterfaceCNC "Color Touchscreen" Controller for: Function & simple part programming and program storage. -- Complete with: (1) 12" Dia. vibratory feed hopper; totally sealed electronically metered glue system with: "Automatic" injector flushing; (1) 4-3/4 G (18 L) Glue Tank & (1) 2.37 G (9 L) water tank.(4) Inclined vertical pneumatic holddown clamps; function selector control for boring only or doweling; anti-slip table surface; rack & pinion drive; centralized dust collection manifold.

For pre-glued PVC, veneer, & melamine laminate coil stock; 0.4 - 1.2 mm edge thickness; up to 35 mm panel thickness cap., automatic coil feed. -- Equipped with: Electronically controlled temperature setting for hot air blower; 3,000 Watts for up to 650° F temperature; (1) Min heat up time. -- Guillotine type front & rear end trim (with fast speed, flying knife); top & bottom flush trims with single motor drive to cutterheads. -- Overhead belt type feeder; 16 FPM feed speed. -- Mounted on machine base with panel support table.

VALPATO LBK-150-ST 1 Feed Through Profile SanderTECHNICAL FEATURES: An added small needle type drum sander can be fitted with drum sanding aggregates of 25, ­30, ­35,­40, ­45 ­50 mm diameters which can be used for tighter curves and smaller radius sanding requirements. Storage compartments (2 in total) are located on each machine extremities, these are easily accessible and can be used for sanding belts and various tooling storage. Sanding belt motor power: 3 Kw Abrasive head motor power: 1.5 Kw Oscillation motor power: 0.38 Kw Feed motor power: 0.75 Kw Motor power for electrical adjustment of sanding group: 0.19 Kw Machine voltage: 480/3/60 Full Load Amps @ 480V: 15A Compressed air: Not required Dust collection requirement one (1) only 6" (150mm) port: 950 CFM Sanding belt speed: 14 Mt/sec Variable speed of the belt: from 5 to 25 m/min Sanding belt dimensions: 150 x 2640 mm Height of working table: 930 mm Dimensions of front working table: 1980 x 250 mm Machine dimensions: 2500 x 900 x 1600 mm Net weight: 1000 KMAIN FEATURES: User friendly PLC touch screen control panel is accessible from 360° by the operator, the control panel is centrally located on the infeed end of the machine. Factory installed variable feed drive (VFD), enables machine to run from 5 M/Min to 25M/min (+/­ 80 ft/Min). The entire sanding plenum rise and fall is motorized, it can be adjusted vertically in height to utilise the full height/width of the sanding belt. An oiling unit ensure long life of sanding plenum rise and fall master cylinder.

VOLVO - L70G: Wheel LoaderVOLVO "L70G" is a versatile wheel loader that got the job done. Specifications: -- Engine: "D6H TIER 4H 171" HP Turbocharged. -- Max. speed: 28.6 MPH. -- Raise time: 5.1 Sec. -- Dump time: 1.2 Sec. -- Lower time: 2.7 Sec. -- Max. bucket capacity min.: 2.4 cbm. -- Hours: 13,560.Equipped with: -- Heat & A/C Cab. -- Air ride. -- Quick hitch.Everything works as it should and ready for work.We can provide financing and assist with delivery to your location.

Volvo L90H Wheel LoaderSpecifications: Static tipping load at full turn: 22,265 lbs Bucket capacity: 2.9 - 9.2 yd³ Log grapples: 1.6 - 2.9 yd² Operating weight: 31,968 - 38,140 lbs Breakout force: 31,470 LBF Engine: Volvo D6J Max power: 1,400 - 1,900 RPM, ISO: 14,396 gross, 184 HP, ISO: 9,249, SAE J1349 Net, 184 HP Max torque: at 1,400 RPM, ISO 14,396 gross 689 LBF Ft., ISO 9249, SAE J1349 Net 689 LBF Ft. Tires 20.5R25 600/65R25Approx 4900 Hours

VOORWOOD M 15A CNC Round End Tenoner & Mortiser for 45° Door --The "M15A" Miter Machine is designed to rapidly make mortise and tenon cuts at 0°, 45° Only, . Parts can be up to 1.5"; thick and up to 4"; wide, and of ANY length. --A primary application for this machine is for miter cabinet door frames. Parts can be quickly transferred from left to right. They are mortised on the left side of the machine and tenoned on the right. The machine can also mill the slots. --Specifications & Equipped with: -- The mortise station has (3) servo-controlled axes (X, Y, and Z) that are coordinated by the machine controller to achieve complex CNC motion. It is equipped with a collet-style router spindle for cutting. The tenon station uses the same X- and Y-servo-controlled axes as the mortise station and is configured for pneumatically actuated in-and-out movement along the Z-axis. The tenon station is equipped with a direct drive shaper spindle for cutting. -- Pneumatic clamping assemblies with non-marring urethane pads are mounted to the hold-down assembly to secure the parts during cutting and these can be adjusted to various locations over the cutting surface. -- M15 Miter Machine operator interface consists of a colored touch screen. For simplicity, the entire calibration, setup, and monitoring of the machine are accomplished using only four touchscreen displays. The program designs the depth and location of both the mortise and the tenon. When the design is complete, it is saved in a recipe format. Once this recipe is opened, the operation is as simple and boils down to feeding the substrate into the machine. -- The full-color touchscreen panel is located on the front of the machine to provide easy access for setting up or operating the machine. Clamping and shaping operations are controlled by operating lighted pushbutton switches.

ATLANTIC - X-5: Modular Dust Collection SystemSpecifications -- Rated @ 3,500 CFM with: 5.5" Static pressure WG. -- (16) 8" x 60" Poly twill cloth; "Quick Release" filter tubes; approx. 440 sq/ft. total cloth area; discharge to (3) plastic bags. -- Equipped with: 5 HP - 3,500 RPM Blower drive centrifugal fan assembly; anti-spark cast impeller; 13.3/4" inlet dia. -- System includes: 230 Volt (factory installed) magnetic starter. -- X-Series Dust Collectors are compliant with: NFPA Regulations 664 & 654 for enclosureless Dust Collectors.Very strong draw; quiet. Includes: 60 Feet, ($ 2,000) quick clamp disconnect pipes.

ATLAS COPCO - GA-55: Rotary Screw Air CompressorEquipped with: -- 75 HP - 1,755 RPM Motor; totally self-contained; single-stage rotary screw air end; 267 CFM at 125 PSI rated operating pressure; max. modulate pressure: 135 PSI. -- Complete with: -- Inlet air filtration; oil injected lubrication; motor starting control system; air-cooled aftercooler; moisture separator; drain trap. -- Includes -- "ELEKTRONIKON" Operator display panel with: Pressure gauges; control mode selection; remote & automatic start; hour meter.

AUTO-V-GROOVE LG-2-SS-FT UNIVERSAL V-GROOVER: -- Specifications:(1) 10 HP - 3,600 RPM V-Grooving head;(1) 10 HP - 3,600 RPM Coving head on opposite side of overhead tool gantry.Both heads are positioned on vertical & horizontal linear rails & bearings for smooth, accurate adjustment. -- Working Cap:Maximum material thickness 1"; 4" min. material width; approx. 12" min. material length; 15" Max. cut from fixed fence; unlimited length of part when cross-grooving. -- Positioning:(1) 2 HP Hydraulic power unit for variable lineal feed rate from 0 - 60 FPM,Extra wide belt feeder moves workpiece on flat phenolic table; raising & lowering of feeder mechanism via manual gear drive. -- Complete with: 100" x 24" Lineal table work surface, 96" Long Cross-Grooving support table set 90° to linear feed direction; Tape applicator; Linear fence, electrical controls. -- Options Include: Auto Transformer for 240/480 v hook-up; ProScale Digital indicator. -- Actual Model is AUTO-V-GROOVE LG-2-SS-FT

AUTO-V-GROOVE AVG-48 MFT UNIVERSAL V-GROOVER: -- Specifications:(1) Head automatic cross & linear V-Groover, 48" max. material width on cross-groove,Unlimited length for linear grooving, 1-1/4" max. material thickness. -- Features:(1) 10 HP - 3,600 RPM Motor, 30 mm dia. belt driven precision cutter arbor, 3-1/4" max. cutter width.2 HP Hydraulic feed motor for infinitely variable crosscut feed speed from 0 - 50 FPM & 0 - 60 FPM for linear feeding.Heavy-duty double belt feeder assembly for linear grooving. -- Includes: Adjustable pneumatic material hold-down bar.(1) 84" x 24" Main table, (1) 20" x 58" auxiliary table, (1) large 96" long floating table on rails. -- Complete with: Automatic tape applicator (12" max. dia. tape roll), manual quick crank tape applicator positioning system. -- Options Include: An assortment of V-Groove cutters as pictured.Actual Model is AUTO-V-GROOVE AVG-48-M/FT.

AUTOQUIP 48S60 SCISSOR LIFTThe Series 35 Scissor Lift Tables are designed and built to provide long-service life, durability, and outstanding lifting power. Series 35 models range in travel from 24″ to 60″ with lifting capacities up to 15,000 lbs. More models and standard options than any other competitive lift table allows for easy customization to meet your specific needs. Single-piece, steel reinforced legs and a 1/4- to 3/8-inch-thick steel platform make for extremely solid construction and easy adaptability. Solid steel leg and added stiffeners provide optimal overall stability and straight, repeatable tracking of the rollers as the lift raises and lowers.Specifications -- 6,000 Lbs Cap., electro-hydraulic operation. -- With 48" x 64" smooth steel platform. -- 7" Lowered height, 48" travel to raised height of 55"; -- 2-Cylinder design -- Complete with: Velocity fuse on cylinders, and maintenance locks on base frame. -- Unit is painted AQ black; .Please note: -- Autoquip to supply recommended GPM flow to achieve a 60 sec. lift time when all (4) lifts are operated at the same time. -- There will still need to be a mechanism to switch on/off (sequence) 1, 2, 3 or 4 lifts at a single time and there may need to be valving to ensure level lifting. -- AUTOQUIP cannot ensure the latter or warranty these lifts since AUTOQUIP is not supplying the complete lifts.

AUTOQUIP 36S128 DL Double Long Scissor Lift.12,800 Lbs. max. cap. with standard 24" x 98" smooth steel platform top. -- 36" Travel with a 7-1/4" height and 43-1/4" raised height; (35) Sec up and down speed. Base frame 24" x 98". -- Power unit with 5 HP remote Super Torque Motor, 240/480 V, 3-Ph, fan-cooled, Intermittent (2 minute) duty. -- Polyethylene hydraulic fluid reservoir with a capacity of 5 gallons. Supply voltage must be specified. -- Complete with; -- Hand held up/down push button control with 10' cord, velocity fuse on cylinder, and maintenance locks on baseframe, -- Options; Guarded foot pedal control, Accordion skirt, larger platforms available. NOTE: Surface mounted lift. Unit is painted AQ black; Pricing subject to change.

AUTOQUIP 36S40 DL Double Long Scissor Lift.4,000 Lbs. max. cap. with 48" x 120" smooth steel platform top. -- 36" Travel with a 6.5" lowered height and a 42.5" raised height; (25) Sec up and down speed. Base frame 24" x 98". -- Power unit with 1.5 HP Super Torque Motor, 208-230-460V - 3 Ph - 60 Cy, fan-cooled, Intermittent (2 minute) duty. -- Polyethylene hydraulic fluid reservoir with a capacity of 5 gallons. Supply voltage must be specified. -- Complete with; Hand held up/down push button control with 10' cord, velocity fuse on cylinder, and maintenance locks on baseframe, -- Option; Guarded foot pedal control.. NOTE: Surface mounted lift. Unit is painted AQ black;

AUTOQUIP 48S40 DL Double Long Scissor Lift.4,000 Lbs. max. cap. with 48" x 144" smooth steel platform top. -- 48" Travel with a 7" lowered height and a 55" raised height; (32) Sec up and down speed. Base frame 24" x 130". -- Power unit with 1.5 HP Super Torque Motor, 208-230-460V - 3 Ph - 60 Cy, fan-cooled, Intermittent (2 minute) duty. -- Polyethylene hydraulic fluid reservoir with a capacity of 5 gallons. Supply voltage must be specified. -- Complete with; Hand held up/down push button control with 10' cord, velocity fuse on cylinder, and maintenance locks on baseframe, -- Option; Guarded foot pedal control.. NOTE: Surface mounted lift. Unit is painted AQ black;

AUTOQUIP 36S25 Scissor Lift. 2,500 Lbs Capacity and 48" x 48" Platform with 24" x 48" base frame. -- 12-Second travel time. -- 6-1/2" Lowered height. -- 36" Travel to raised height of 42-1/2". -- Electro-hydraulic, 1-Cylinder design. -- Internally mounted Super Torque 1.5 HP TENV motor with prewired motor starter. -- 24 Volt Control transformer, -- 10' Straight SO cord with hand held up/down 24 V push button. -- 10' SO Power cord. -- Options: Foot pedal control, oversized platform up to a max. of 48" x 72".

AUTOQUIP 48S25 Scissor Lift.2,500 Lbs, Electro-hydraulic, 24" x 64" standard platform and 24" x 64" base frame. -- 7" Lowered height, 48" travel to raised height of 55"; .75 HP TENV motor, 1-cylinder design. -- Complete with: Hand held push button control with 10' cord. -- Options: Max. platform size up to 48" x 96", foot pedal control, accordion skirt ask for pricing.(Standard specs)