- End Matcher for the Continuous Feeding of Random Length Work Pieces - Minimum Working Length: 160mm (6.3") - Working Width: 30-250mm (1.18"-9.84") - Working Thickness: 10-30mm (0.39"-1.18") - Two 7-1/2 HP, 3ph Profiling Motors - Spindle Speeds: 6,800 RPM - Spindle Diameters: 40mm - Cutterhead Feed Motor: 1 HP - Two 1-1/2 HP Motors for Infeed/Outfeed Conveyors - Infeed/Outfeed Conveyor Sizes: 123" x 11" - Sound/Safety Enclosure - New in 2004 - Current Voltage: 460V

Friulmac Dualfeed Double End Chop Saw & Moulder Feeder Friulmac Dualfeed Automatically Trims Workpieces and Feeds into a Moulder Cutting Length: 200mm - 1500mm (8" - 59") Cutting Width: 30mm - 110mm (1.2" - 4.3") Cutting Thickness: 15mm - 60mm (0.6" - 2.4") Trim Saw Motors 5.5HP (4KW) Feed Motor 3.5HP (2.64KW) Anti-Kickback Spring-loaded Top Pressure System w/ Manual Adjustment and Readout Manual Board Length Adjustment w/ Readout Manual Blade Height Adjustment w Readout Hopper Fed Voltage: 460V 3PH

2002 Randomat E Endmatcher Manufacturer’s Specifications Working cap.: width 1-3/16" to 9-7/8"; thickness 3/8" to 1-3/16" and length 7" to ???? Feed: (2) 5.5 HP motors for infeed and out feed 10" x 120" belt conveyors. Positioning motor (2) 1.5 HP to shaper heads for tongue and groove. Sensor activated stops for true cut positioning. Approx. 10-12 cycles per minute. Profiling: (2) shaper heads 7.5 HP with 7,500 RPM with spindle dia. 40mm. Tool cutting circle to 8-5/8

Gabbiani Gallixy 125 Rear Loading Panel Saw

2019 Gabbiani P 55 Front Loading Panel Saw Like New !

Gabbiani Galaxy 125 Panel Saw Manufacturer Specifications to be confirmed: Cutting length; 3800mm Pusher stroke; 3800mm Speed is variable, via VFD Number of grippers; 9 Main motor power; 18.5kw (25.5hp) Saw blade diameter max; 420mm Saw blade projection 125 mm

Gannomat Pro-Line 50 • Row of holes as well as line drilling in the SYSTEM 32 mm • 50 (2 x 25) holes in one drilling cycle

Gardner Denver Air Compressor - 25 HP - Gardner Denver Air Dryer - 250 Gallon reservoir and stand

Gau Jing GS-623 Moulder 6 Head 460V 3ph 60hz Good Running Condition Recently Removed From Service

Generac 200 HP Genset

This motor was rebuilt in 2024 for a chip mill and never put into production. It is ready to ship immediately. 1500 HP 356 RPM

General Thermodynamics Genset Set up for 480 volts Low Hrs., only 1,728 hrs., 275 KW, Cummins Deisel. Always started very well and ran extremely smooth.outside enclosure has easy access doors all around. Deisel tank holds enough to run genset for at least 24 hrs.+ Cummins Diesel engine

Giben K305 Edgebander Manufacturer specs (to be confirmed): Standard Configuration Panel Thickness: 10~60mm Edge Thickness: 0.4~3mm Motor Power: 2.35Kw Maximum Curve Radius: 20mm Cutter Maximum Range: 50mm Working Pressure: 0.6 MPa Outline Dimension: 960 x 950 x 1000mm Gross Weight: 280Kg Voltage: 220-480V

Go Fast Resaw 15 HP Motor Put under power to test, never put into production.

2023 Go Fast 6x6 Resaw 15hp motor 480V Good Condition

GoFast 2-Head Resaw 10 HP main motors Go Fast Board Deduster

Go Fast 5-Head Resaw Unit was cut into two pieces and can be put back together with a weld in the middle. Approx layout is 31' x 8'

Approximately 27" width capacity 1/2" - 3.9" diameter capacity 10 HP spindle motor 1800-3200 spindle speed 3 HP hydraulic feed PLC sequence controller

3" - 41" length capacity 1" - 3" square or round diameter capacity 15 HP spindle motor Spindle speeds 2250, 3200, 3525, 4625 rpm hopper feed

12' Arm 250 Lbs Capacity 4 HP Pump Per owner: head only turns horizonally