This machine is no longer needed at the current facility. It is ready to be removed ASAP. Buyer will have to remove the system. 220 Volt/3 ph

Holzma Optimat Rear Load Panel Saw, Model: HPL 11/43/16 Year: 2006 4 Front Air Floatation Tables 169” Cutting Length & Pull Back 4.9 Blade Projection 18 H.P. Blade Motor 3 H.P Scoring Blade Motor Variable Saw Carriage Speed 32-410 FPM 10-125 MPM Constant Return Lift Table 230 Volts, 3 Phase, 60 Cycle Operation

Homag BMG 311 Venture 316L CNC

Homag Double End Tenoner System will be available approximately August 1, 2023 Also available with a direct transfer conveyor and [Gabbiani DET](https://www.carolinamachinerysales.com/listings/4073350-used-2003-gabbiani-sqv-sqi-double-end-tenoner) currently running inline.

Homag BOF 311/37/15/R CNC Router Specs (to be confirmed): Homag "Vantage 12L" CNC Router Aluminum router table 60" x 144" working area Gridded Pneumatic reference stops Vacuum gauges Foot pedal control Drill unit Nine (9) vertical spindles One (1) horizontal spindle (two outlet) in X axis One (1) horizontal spindle (two outlet) in Y axis Router 16 HP HSK (quick-change) CW/CCW rotation Variable RPM Ten (10) position rotary tool changer Sound enclosure Front safety mats Safety fencing with interlocked access door Controller Flat screen monitor Standard keyboard and mouse Remote control pendant Also included: Laser projecting unit Ceiling mount

Homag Espana CH-03/32/32-PLUS Panel Saw Still under power and available for inspection. 230/480 V

Homag BST 500

Homag KAL 310 NOT INCLUDING THE RETURN Year of MFG 2006 Control voltage 24 V total connected load 50A recommended fuse 28kW nominal current pprox.. 39A Dust extraction air velocity (min.) 28 m/sec (91.84 ft/sec) air volume 4090 m3/hr (2407 cfm) static pressure 250 mm/ws (9.84”/ws) CompressedAir connection size ¾” pressure required 7 bar (100 psi) consumption / volume 705 sl/min (24.89 cfm) Foundation requirements according to layout drawing # 5-236-01-0360 Electrical equipment installed according to UL regulations. Voltage supplied must not fluctuate in excess of+/- 5% of its stated value. Voltage must be balanced phase-to-phase and phase-to-ground. Note: The stated values are only applicable to the machine as specified. Adding or deleting optional equipment may change service connection requirements. In case ofvariations in technical specifications and capacities between the base machine and working units, the specifications and capacities given for the working units are to be considered correct. Conditions offloor at installation site must adhere to foundation plan. Adjustable lnfeed Fence Homag Unit #0005 • with digital mechanical counter Pre-Milling Unit Homag Unit #3481 HOMAG KAL 525 • with two (2) motors 3 kW, 150 cycle, 9000 rpm • for max. tool diameter of 125 mm (4-15/16") • equipped with trimming column • two (2) horizontal and cross slides with spindle adjustment • electro-pneumatic horizontal jump movement of first motor • two (2) dust extraction hoods • air jet for panel cleaning • with two (2) DIA jointing heads 125 x 35 x 30 mm(4-15/16" x 1-3/8" x 1-1/8"), DKN, z = 2 x 3 • max. workpiece thickness 30 mm (1-1/8") • electronic frequency inverter for control of motor speed and braking Noise Protection Stepped Homag Unit #0424 • for pre-trimming unit • allows for inlay of long strips • centralized dust extraction port Panel Pre-Heater Homag Unit #2325 • quartz lamp for heating substrate edge before glue application • for improved edge quality and optimum bonding QA 34 Quick Melt Gluing Unit Homag Unit #2123 • specially designed by Ho mag - the original innovator of the quick melt syste • lower reservoir unit is designed with only seven (7) wearing parts, which allows for ease of adjustment and reduces maintenance costs • ideally suited for quick heat-up time and color changes • one bolt secures lower unit to drive mechanism • special coupling eliminates alignment of universal drive joint • digitally displayed thermostat for both upper and lower unit, along with heated glue roller allow for excellent control of temperature for optimum bonding results • individual adjustment for front and rear glue gates • upper reservoir for glue granules • glue roller diameter 34 mm (1-11/32") • lower melting unit equipped with automatic control of glue level Glue Roller Drive Homag Unit #2141 • eliminates glue charring on glue roller • lengthens pot life of glue during idle running time o

As Taken From Service: Includes return conveyor

Homag Centateq N300 CNC Router 5x10 Table Offload conveyor Schmaltz overhead gantry system

Homag D-200 Drill & Dowel Inserter

Homag Cabteq S-250 Case Clamp

Homag Drillteq V200 Model Optimat BHX 055

Homag Optimat NBP084/ Vantech 480 4x8 Bed 12 HP Spindle (replaced in 2019) 7-Position Boring (3) Vacuum Pumps Clean Machine

Manufacturer’s Specifications - For banding edges of up to 3 mm and workpieces of up to 40 mm (60 mm - 1130 FC | 1130 AT) - Glue applied directly onto the workpiece to ensure constant application (i.a. for processing of PUR-glue). - Two-motor end-trimming unit for optimum cutting results - Contour trimming unit for rounding corners - Freely configurable post-processing for a high level of flexibility - Zero joints - airTec unit for a perfect zero joint finish

Homag SWT 100 series includes the following features: Height Adjustment System – 100 Series Conveyor bed is adjusted by four (4) large diameter dual supported threaded spindles • Calibration sanding • Veneer sanding • Fine sanding of solid wood • One machine for multiple sanding jobs • Easy to use and quick setup times • Automatic Star Delta starting • Maintenance-free electrical main motor braking • Electronic abrasive belt oscillation with photo eyes • Pneumatic tensioning of abrasive belt • Safety switch-off of machine during faulty operation • Rubberized pressure rollers • Workpiece thickness: 3 mm to 160 mm (1/8" to 6") • Working width: 1100 mm (43") • Abrasive belt width: 1120 mm (44") • Abrasive belt length: 1900 mm (75") • Abrasive belt changing side: left Conveyor Drive System Variable frequency-controlled feed speeds of 2.5 – 13 m/min. (18 – 42 ft/min.) with automatic conveyor belt tracking and rubber drive roller Touch Screen Display and Control ECO Mode Automatic machine stop with advance warning function for energy saving during idle time of the machine. Head 1: R Head - Steel Profiled Contact Roller Sanding Unit This sanding head features a 140mm (5.5”) diameter profiled steel contact roller with automatic positioning of the contact roller upon selection with integrated grit compensation. The steel contact roller is ideal for calibration, providing optimal calibration sanding results: Features & Details: HOMAG SANDTEQ W-124 RC (continued) • 15.6" graphically supported color touch screen • LCD-TFT color screen with 800 x 600 resolution • Metric or decimal inch input (3 decimal places) • 125 program memory • Automatic machine control • One-button start (Star Delta) • Sequential motor starting • Plain text error messaging at the operator terminal • Program backup via USB stick possible • Controls air or segmented pad options (only on models such feature) • Manual head locking for fast abrasive belt changing • Automatic Star Delta starting • Maintenance-free electrical motor braking (no wearable parts) • Grit compensation and automatic positioning for calibration • Poly-V drive belt for maximum power and minimal vibration • Non-contact photo eyes for abrasive belt oscillation • Contact Roller (Steel): 140 mm (5.5”) • Drive motor: 17.4 kW (23 hp) • Belt speed: 18 mps (59 fps) • Dust outlet size: 160 mm (6.5") Head 2: C-Head – Combination Head Sanding Unit This sanding head features a combination sanding head with an automatic positioning contact roller with grit compensation as well as a segmented sanding pad for finish sanding. The profiled rubber roller is ideal for light calibration or finish sanding while the segmented pad provides performance versatility depending on the application: EPS Electro-Pneumatic Segmented Pad System (Head 2) This head is equipped with an electro-pneumatic controlled segmented pad. This feature is designed for precision sanding, with 35 mm pad resolu

- Min. panel height 0.47 inch - Max. panel height 1.57 inch - Min. edge thickness 0.01 inch - Max. edge thickness 0.24 inch - Max. forward feed speed 82.02 ft/min - Top pressure with rubber belt - No. Panel Sizing / Milling units 2 Pre-milling unit - Lamps to preheat the side of the panel - Edge coil magazine - Gluing system - glue pot for EVA hot melt glue - premelter for EVA hot melt glue - QA65 - Roller set to press the edge - no. pressure roller 7 - with positioning by NC No. Edge Processing Units 6 First Processing Unit - End trimming Constructor model HL81 - no. motors 2 - with positioning by NC Second Processing Unit - top and bottom rough trimming - no. motors 2 - with positioning by NC Third Processing Unit - Multi Function trimming and corner rounding - Constructor model - FK11 - no. motors 2 - with positioning by NC Fourth Processing unit - edge scraping - with positioning by NC Fifth Processing Unit - glue scraping - with positioning by NC Sixth Processing Unit - buffing - no. motors 2 Spray unit Control system Power Touch

Weeke Model Optimal BHX050 Vertical CNC Machine 8 Vertical Drilling Spindels 2 Horizontal Spindle in X-Direction 1 Horizontal Spindle in Y-Direction Grooving Saw in X-Direction 1 Powerful 5kW ETP 25 Routing Spindle Vector Speed: X-30M/Min Y-30M/Min Z-15M/Min

53” capacity (1) drum head (1) combo head 230 volt 3 phase at lease (10) spare belts Available late July/early August 2023

Used 1995 Hurst Hybrid Boiler system 200 HP 150 PSI 1– Hurst Hybrid Boiler 200 HP 150 PSI Boiler 1 - Hurst Boiler 200 HP Woodfired Furnace for Boiler vessel with cast iron grate system. 1 – Deaerator Tank 1 – Blowdown Separator for fuel storage equipment 1 – 8” Underfeed stoker System 1 – 10” Metering Bin Screw Conveyor with Hopper 1- 20HP Over fire air combustion fan 1- 15HP Under fire air combustion fan 1- Hurst multi-cyclone collectors 1- Induced draft fan