Has (2) Blades Will cut up to a 12 x 12" Powered by (2) 20 HP 460 Volt 3 Phase motors Runs (2) 1 1/4" band blades Excellent Condition, (new condition with less than 4 hours use).

Nyle Firewood Dry kiln No chamber included

Nyle L500 Kiln (High temperature system)

Nyle Firewood Kiln Holds approx 9-cords

Nyle L200M Dry Kiln System still under power. Purchased new in 2021.

2015 Nyle L500 Dry Kiln 5 hp Compressor 5 24" fans Chimney All Controls Included Very Good Condition

2003 Nyle L500 Dry Kiln 8 Fans and Insulated Container Included Good Condition Available Immediately

2004 Nyle L1200S Dry Kiln Good Condition Available Immediately

Nyle L1209 Dry Kiln 230 volt 3 Phase No enclosure …controls only

Nyle Dry Kilns - 2024 Kiln: 29' x 42', 40 MBF with HT54 - (2) 1998 Kilns: 28' x 40'. Both units in good running condition. New controls in 2016. - 1994 Kiln: Missing some sheet metal and attached to a storage building. 28'x40' There is one new kiln and three older kilns that the seller has available. All are ready to be removed from the current location. The older kilns had new controls installed in 2016.

2008 Pallet Chief PC IV Stored Inside

Pallet Repair System Disc Dismantler Pallet size: 3.875" Stringer Width Max. (.098 m) 1.25" Deckboard Thickness Max. (.031 m)

This machine was purchased as "rebuilt" by the manufacturer and never put into service at the current location. Ready to load.

Paul AB920 Rip Saw Scanning Fenceless Infeed Infeed & Outfeed (not including decks) The machine has one fixed and 2 moving blades. The minimum distance between the moving blades is 44 mm (1.73"). The maximum distance between the moving saw blades is 210 mm (8-1/4"). The machine is designed for incoming boards with the following min./max. dimensions Length: 4' - 16' Width: 2" - 19" Ripped widths: 1.75" - 8" Thickness: 1" - 2" 480 Volt, 60 hz., 3 phase electrics 75 HP main motor Automatic edging separation after the saw Feed speed up to 300 fpm Fenceless infeed system with automatic skewing capability 16 width sensors on the infeed system

This machine was reported to be in running condition when removed from service. Looks like a Pendu. Cannot find a plate on the machine to confirm. this is a single arbor gang and it does not have a sizer. 75 HP Main Motor 5 HP Drive motor

Pendu E-4000 Gang Saw 75 HP on bottom and 75 HP on top arbors 20 HP on blower Press rolls are all original and in very good condition Comes with starters and 3000 amp disconnect box Some hydraulic upgrades Very good condition Seller will disconnect and load

Pendu M-4000 Gangsaw 75 HP on bottom and 75 HP on top arbors 20 HP on blower Press rolls are all original and in very good condition Came from sheltered workshop and was never used much Comes with starter boxes Will disconnect and load.

Pendu Stacker No hydraulic pack

2016 Pendu 4600 Board Stacker Rollout Conveyor Hydraulic Unit Very Good Condition

Selling as a complete package: Pendu Sharp Chain Scragg (2) 100 HP Motors with soft starts Infeed System Log turner Operator Cab All controls and electrical (2) Log Decks: 3-Strand and 4-Strand Pendu bark conveyor: 30'4" Long with 180 degree tail section, 17" flights 2" high, flights spaced 18-3/4" apart Barn Sweep: Elevated conveyor: 25'4 Long, (2) Hold downs with idlers, chain has 17" flights that are 2" high, leg brackets, Approx 90' of Barn Sweep conveyor with chain and drive motor