MLS Number 12544095 2021 Caterpillar 950M Wheel Loader 3698 hours Cat diesel Cab with AC All wheel drive No required repairs 4.75 cu yd bucket Cutting edge 70% Firestone 23.5-25 tires 80%

MLS Number 11744642 2016 Caterpillar 910K Wheel Loader 7373 hours Cat C3.8 engine Cab with AC All wheel drive Solid tires 80%

2002 Caterpillar 500 KW Generator 850 Hours Low Voltage Output Two Available

Caterpillar Generator 40 KW Single phase Silent package 225 gallon fuel tank 554 hours Work ready

MLS Number 12231702 2011 Clarke's Industries Bag House ? Explosion doors ? Abort gate at outfeed ? Abort gate at infeed ? Backdraft damper at infeed ? Spark detectors on infeed and outfeed lines ? Airlock ? Backdraft Damper on dust outfeed line ? Deluge System This baghouse is fed from a fan that has suction from Edger, 6”-10”-12”-20” Ukiah (chip/saw) and 20” sawbox. The sawdust from the discharge line under the airlock of the baghouse is sucked into Discharge blower (See Item#2). The dust outfeed line at the middle of baghouse, which discharges the dust fines during the cleaning cycle of bags, returns the fines to the baghouse fan. The Baghouse supplies air back into the building. This baghouse is fed from a fan with following specs: OEM & Model: Clarke’s Industries, Model MH-11, Serial 11OCWUBI3923 Driver: TECO 350 HP, 1785 RPM, 5009C Frame Motor Capacity: 66000 CFM Spark Detection Control System OEM/Model: Clarke’s Industries, Pyroguard CXC-2 Buyer responsible for dismantling.

Denis 948 Gang Saw

MLS Number 11922341 Denis Comact 948 Gang Saw Edger 6" infeed table Spare guides

MLS Number 11413038 Cooper Overhead End Dogging Scragg With Debarker And Gang Edger Transfer Chain Conveyor x 60’, H82,1-7.5 HP 480V gear drive 54" Cut Off Saw, 20 HP 480V motor, hyd stop gates, 20 HP hyd pack 4 strand x 12' long Debarker In Feed Deck, 5 HP 480V gear drive, H78 16” wide x 19’ long log haul belt conveyor (driven from debarker in feed tire drive) Cambio 24" Debarker, 75 HP 480V drive, spiked in/out feed rolls 20 HP 480V drive 3’ wide x 36’ long hour glass rolls transfer, 7.5 HP 480V gear drive 5-strand Scragg in feed deck x 20', H82, hyd log stop loader, 7.5 HP 480V gear drive Cooper Overhead Scragg Mill, 30 HP 480V 150 gal hyd package, variable speed cable drum feed works with pantograph arm Log positioning rolls on infeed w/ double overhead dogging system, 48” dia. saw husk(125 HP 480V each saw), setworks control 2-18” wide 2-position slab and side board belt conveyors, operators control cab w/ controls, camera and monitor for centering log 8-16’ length capacity, maximum log dia. 22”, largest square cant 12” x 12”, smallest square cant 4” x 4” 5-strand lower camel back landing transfer x 9’-6” long, 4-strand hyd lift transfer to gang edger and cant center bypass Center bypass rolls and belt conveyor to edger out feed landing transfer 10” mainland gang edger w/ 200 HP 480V drive,34” inserted tooth saws with 5/16” kerf(24 spare saws with collars), 2-2-2-4 spacing 6” x 50” mainland board edger w/ 150 HP 480V electric drive, 24” inserted tooth saws with 5/16” kerf, 8”-4”-4”-10”-6” pockets, 7-individual actuated self tailing belt conveyor out feed c/w splitters Camel back transfer,4-strand x 27-1/2’ long, H78B, 5 HP 480V gear drive 2-Saw Trimmer, 4-strand x 10’ long, 16’-4” between 20” dia. saws,10HP 480V drive on feed works and saws, 16” wide x 28’ long out feed belt conveyor, 5HP 480V gear drive 4-strand x 26’ long H78 camel back transfer w/ 5HP 480V gear drive

MLS Number 10791171 Cornell 24" Chop Saw All live rollers 16' infeed 8' outfeed Sold as is.

Cresswood Model EF 50-100A Horizontal Shredder 100 HP 12' Vibratory Conveyor (2) Feed Rollers Screw Auger Discharger Inclined Conveyor with 10" Magnetic Head Pulley Discharge Height 116" Crossbelt Magnet Soft Start Extra Set of Cutters 2 New Screens 1/2" Screens

?Cresswood EF-60 Grinder 100 HP 60” Wide Feed Opening Includes 60”W Vibrating Conveyor (shaker table)

Cummins 600KW Enclosed Generator Skid Mounted - 277/480V - 60Hz 638 Hours Digital Controls Unit has been tested

2004 Detroit Diesel MTU 660 KW Generator Skid Mounted 277/480V - 60Hz 540 Hours Digital Controls

DIEHL 990 GANGRIP SAW Product No. 1001 30 HP - 3600 RPM arbor motor-AB size 4 starter-110 volt controls 12 " arbor width with 3-1/2" maximum thickness 8 roll feed - 4 top (powered) - 4 bottom Anti-kick back fingers : top and bottom One (1) saw cartridge-2 3/4 " saw blade bore New arbor bearings 5 HP feed: single speed Rip fence Outboard bearing on arbor 3" throat capacity to 1st saw blade Cleaned, painted and checked Serial # : 54174 Year: 1958

Diehl model MR-90 Gang Rip Saw Twelve ( 12 ) inch saw arbor width capacity- Roll feed 50 HP 3600 RPM arbor motor -direct coupled wired 480 volts, 3 phase- new motor bearings 2 HP variable speed feed motor 50 to 150 FPM feed speed-variable Four powered top feed rolls- Excellant feed roll gears 12 inch arbor with one (1) sleeve with spacers Adjustable rip fence Serial number : 66M-1668 Cleaned , checked , and painted

Donaldson Torit DCE- Environmental Control Booth & Dust Collector Torit ECB-4 Modules, complete with control panel Built dust booth and own lighting. Environmental Control Booth Powerful, Self-Contained Dust Collection The Donaldson Torit® DCE Environmental Control Booth, ECB Work Station, is ideal for finishing works on large and irregularly shaped parts. This self-contained working environment is specially designed to remove fine airborne dust from multiple sources without interfering with workers’ movement or visibility to ensure efficient dust control. The unique booth design is complete with lighting, sound- proofing and built-in dust collection. It requires no ductwork, and re-circulates the cleaned air for reduced energy costs. Workers inside the booth enjoy complete freedom of movement, cleaner air and excellent visibility. The powerful filtration capabilities of ECB Work Station prevent migration of dust to other parts of the plant, protecting workers outside the booth from the dust and noise generated inside the booth. Stand-alone unit for easy moving at the plant High filtration efficiency with Ultra-Web® cartridge filters Freedom of movement and improved visibility Flexibility to increase capacity Requires no ductwork Safely recirculates cleaned air for reduced energy costs

Dustvent Cyclone Dust Collector 3 phase 10 HP Currently under power Works good

Dyna-Bignell PP 800 Stake Pointer Handles up to 8" material Approx 10-15 years old Includes 3 doming heads 7", 5.5", and 4.5"

MLS Number 11948224 Edmiston Gang Saw Edger Package Completely rebuilt Edmiston gang saw edger Can accommodate cants up to 4" tall and 8" wide Heavy duty infeed and outfeed rollers New mandrel and roller bearings installed in Fall 2022 ($14,500) Comes with extra mandrel and bearings Four sets of strobe blades with spacers Currently running on PTO power unit Includes Westinghouse 100 HP 3 PH 575V motor and starter for electric set up 12" dust blower with 20 HP 3 PH 240V motor Includes ductwork, steel pole, steel cyclone/switch valve tower Can blow into trailer or drop in dumpster Videos available

MLS Number 11955127 Filer-Stowell42 Inch Sawmill Carriage No controls 200 HP DC drive motor Control cabinet and spare parts 125 HP DC drive motor also available at extra cost.