Made for Solid and Engineered Flooring 2 Cutting Blades - 10 HP each 4 way adjustability for each blade Servo drive- programmable varying speed for a variable sawmark look Touchscreen Operation 480V 3 Phase Schneider Electronics

NEW 24" WIDE 4 HEAD 1. Also Available in 36”, 51” Widths 2. Work piece thickness: 2-80mm 3. Min working length: 300mm 4. Feeding speed: 5-20m/min 5. Available in 2-6 head configurations Features: 1. Feed belt thickness 5mm, high temperature resistance fish bone belt. 2. Schneider Electronics 3. Delta frequency converter control each brushing heads individually 4. Adjustable height pressure roller- 2 rolls per head 5. Height counters with individual height adjustment 6. Multiple wire diameter and bristle lengths available Optional -Precision automatic lifting motor for height adjustment Electrical Requirements: Operating voltage: 460 Volt/60Hz/3 Phase

Woodtech 16" Resaw with return conveyor

Specs: Model GH-2 3 Hp, 230/460 volt three phase drive motor Belt drive to spindle arbor design (2) Spindle drill head with adjustable centers Min drill centers 1" Max drill centers 9" Spindle speed 3000 rpm Machine weight 650 lbs Vertical table adjustment 4" 24" wide x 12" long machine work table Pneumatic stock clamping Pneumatic cylinder stroke of drill head Foot pedal pneumatic controls Square D push button motor controls

Yaskawa Motoman UP50N Robot YR-UP50N-A00 Payload 50kg Control Box Teach Pendant Yaskawa Motoman UP50N Robot Type: YR-UP50N-A00 Payload 50kg

Yates A20-12 Planer Infeed Deck Tilt Hoist 575 V Includes: Misc parts, heads and attachments for S4S and T&G. This system was removed from service this Spring. It is ready to load.

There are two of these systems available. They were recently removed from the current operation and available immediately.

The frame is a massive, compact and solid casting which takes less floor space for its capacity The feed drive is built to stand up under the hardest kind of services The feed rolls are of such design that the advantages of the open side type of construction are combined with of the advantages of the inside The top and bottom head assemblies are of the most substantial construction The top head chip breaker is made of chilled cast iron section, each section being spring loaded and adjustable The side head spindles are short and of large diameter The side head chipbreaker moves in and out with the head and is also provided with an additional screw adjustment for close setting The bedding is continuous throughout the entire length of the machine

Used Yates American Model B-26, 24” Double Planer, 75HP top, 40HPBottom, top and bottom 10 knife cutterheads, on the fly top and bottom jointers, 3 phase 480volt electrics, slide out lower cutterhead, top fixed cutterhead, 3-3/4” thickness capacity, approx. 20HP hydraulic feed works, power bed raise and lower, sectional pneumatic chip breaker, top infeed/outfeed rubber rollers.

Yates American E-12 End Matcher System for tongue and groove flooring includes: Belt, Straight Line Blade, 3-blades, Infeed conveyor to end matcher, transfer conveyor from first machine to second machine, variable speed outfeed conveyor

Planer Head Set Up Stand

220v 3 phase 2hp motor Controls work, motor runs and spindle turns Spindle raising mechanism has pin sheared in bevel gear. Includes overarm casting & mobile base.

Air Compressor Water Separator Single Phase 115V 16hz Good Condition

15" color "Touch Screen" with Industrial Computer for setup and running CNC control of machine setup in less than one minute All components sized to handle 6x30 dowels Three v-groove heads with minimum 4" center to center Three banks of nine spindles for drawer front drilling One additional nine spindle bank to handle four sided drawers Two nine spindle horizontal banks for dowel drilling Runs up to 22 parts/minute in production Application Ability to v-groove drawer parts from 25" to 96" in length Ability to run parts as short as 10" without v-groove Ability to handle parts from 2-1/2" to 13-3/4" in width Ability to handle material thicknesses of 7/16" & 1/2" Makes box drawers with dowel construction Makes box drawers with 3 miters & 1 butt joint CNC Setup of machine Hopper loading of parts Parts feed through to the rear of the machine Like New Machine has run less than 100 parts. NEW PRICE: $235,000

15" color "Touch Screen" with Industrial Computer for setup and running CNC control of machine setup in less than one minute All components sized to handle 6x30 dowels Three v-groove heads with minimum 4" center to center Three banks of nine spindles for drawer front drilling One additional nine spindle bank to handle four sided drawers Two nine spindle horizontal banks for dowel drilling Runs up to 22 parts/minute in production Application Ability to v-groove drawer parts from 25" to 96" in length Ability to run parts as short as 10" without v-groove Ability to handle parts from 2-1/2" to 13-3/4" in width Ability to handle material thicknesses of 7/16" & 1/2" Makes box drawers with dowel construction Makes box drawers with 3 miters & 1 butt joint CNC Setup of machine Hopper loading of parts Parts feed through to the rear of the machine Like New Machine has run less than 100 parts. NEW PRICE: $235,000

Accu-Systems MMTJ Door Machine

Manufacturer specs: Accu-Systems Miter Door CNC Machining Center Model MMTJ. 3-Axis control for high quality joints and flexibility in machining various sizes of profiles (X, Y, and Z) 2 working zones 3 HP high frequency spindle for mortise (24,000 RPM) 6 HP high frequency spindle for tenon (18,000 RPM) 1" x 3.5" machining capability

75 KVA 480 volt to 240 volt

AEM 36" Sander

AER 5,000 CFM Dust System