Dust blower used on Resaw or Edger 550 Volt 3 Phase 1-1/2 HP 3400 RPM

English 600 HP Boiler - (2) Units available New in 2000 One is set up for wood and only run for 3-years The second is wood/oil backup and only test fired 300' Covered Waste Conveyors available to transport waste to boilers Large capacity bucket load/silo available to store wood waste Complete loading/unloading augers available All pumps, condensate tanks, piping, electrical, catwalk, exhaust, infeed bins, suit bins, augers included. Two large stacks also available

Excalibur Smart Incising for Round Timbers from Timber Treatment Solutions (TTS). - 63 mm - 200 mm Diameter (1.29"-7.8") - Minimum length of 200 mm to no max (7,8" - (9) Incising Heads - Self cleaning system for blades - Allows superior preservative penetration with pressure treatment - Optional: Customized builds for larger pole requirements

Timber Treatment Solutions now offers an advanced incising solution for square sawn timbers with EXCALIBUR PRO, allowing a superior penetration of the wood in the subsequent preservative pressure treatment. It offers the ability to incise specific sections of post, saving on preservatives while still focusing the treatment where it is needed most and helping to retain visual product aesthetics above the ground contact line. - 1” x 1” to 20” x 20” Section Capacity - No maximum length - Incision depth up to 3/4" - 2 sets of 2 incising heads, fully sequenced with each other - Self cleaning system for blades - Incises all four faces in a single pass with incising pattern sides finishing at the same point - Full- or part-post straight-through continuous incising with a simple choice of the length and place of incision anywhere on the post - Mechanical blade separation system allows rapid setting of the machine for different timber sizes - Auto self-calibration to ensure accurate incising every time and reduce operator error

Frick Sawmill 4 Head Block Mounted on a drop deck trailer. Everything folds up for transport. Includes: Cummins motor

Friulmac Dualfeed Double End Chop Saw & Moulder Feeder Friulmac Dualfeed Automatically Trims Workpieces and Feeds into a Moulder Cutting Length: 200mm - 1500mm (8" - 59") Cutting Width: 30mm - 110mm (1.2" - 4.3") Cutting Thickness: 15mm - 60mm (0.6" - 2.4") Trim Saw Motors 5.5HP (4KW) Feed Motor 3.5HP (2.64KW) Anti-Kickback Spring-loaded Top Pressure System w/ Manual Adjustment and Readout Manual Board Length Adjustment w/ Readout Manual Blade Height Adjustment w Readout Hopper Fed Voltage: 460V 3PH

Fulghum 10x90 Drum Debarker Includes Infeed

Gardner Denver Air Compressor - 25 HP - Gardner Denver Air Dryer - 250 Gallon reservoir and stand

Generac 200 HP Genset

This motor was rebuilt in 2024 for a chip mill and never put into production. It is ready to ship immediately. 1500 HP 356 RPM

General Thermodynamics Genset Set up for 480 volts Low Hrs., only 1,728 hrs., 275 KW, Cummins Deisel. Always started very well and ran extremely smooth.outside enclosure has easy access doors all around. Deisel tank holds enough to run genset for at least 24 hrs.+ Cummins Diesel engine

Go Fast 5-Head Resaw Unit was cut into two pieces and can be put back together with a weld in the middle. Approx layout is 31' x 8'

Go Fast Resaw 15 HP Motor Put under power to test, never put into production.

GoFast 2-Head Resaw 10 HP main motors Go Fast Board Deduster

2023 Go Fast 6x6 Resaw 15hp motor 480V Good Condition

Griggio C250 Rip Saw 250 mm Wide belt (10")

Grizzly 24" Band Resaw

Grizzly 12" Resaw

Alden 12" Gang Saw Hazeldine Model D-45 Stake Chisel Pointer 12" Dual Blade Stake Pointer Smooth Hytrol Conveyor 2 Stra-Pak Banders Model D-53 Samuel Bander Model P-725 2 U-Line Banders Model H-959 Samuel Bander Model TP-202 4 Rolls U-Line S-5692 Poly Strap Blades, Tips, Accessories Fairfield Model 55 Swing Saw GoFast 10 h.p. 6x6 Resaw Whirlwind Pop-Up Saw Model 1000L

Heil 15x32 Triple Pass Drum Dryer 8-10 TPH Drying Capacity Webb Burner Complete Dust Collection All Electrical & Controls 200 HP Wood Hog