Komptech Terminator Shredder Approx 3700 Hours

LAMB 23x27 inch opening grinder with 150 HP motor, 1 3/8” screen and starter control. 460 volt 3-phase

Leadermac /Cantek JF330 Profile Grinder New never used Maximum length of straight grind 12? Maximum length of profile grind 12? Maximum diameter of swing 12? Max. depth of profile with 140mm hub 1.6? Max. depth of profile with 110 mm hub 2? Grinding motor 3 HP Grinding wheel size 225 mm dia. x 60 mm bore Machine dimensions 41 x 44 x 59? Machine weight 1850 lbs

(2) McConnell 40-50 MM BTU Gas Burners available

MEC 12'x42' Triple Pass Drum Trunions Cyclone available

MEC 8'x30' Triple Pass Drum Dryer 12 MM BTU McConnell Gas Burner 8' Cyclone

225 KVA 480 volt to 208Y/120

Brand New, Never Used 5' x 10' 3 Screening Decks

Montgomery 100 HP Hammer Mill Includes: Outfeed conveyor and Infeed Hopper

Newman G200 Knife Grinder

Newman Shaving Mill Already pulled out of service and ready to ship.

Very clean Newman G-200 Knife grinder. In good working order, grinds 17" on the inside and 20" on the outside.

Nice Newman G-280 tub grinder. Everything functional just needs cleaned.

Nice Newman G-280 that has been refreshed. Has extra cylinder wheels that come with it.

Complete Chip Mill that is ready to be moved System includes: - Log Deck - Log Singulator - Control Room - Nicholson A5 Debarker - Peeled Log Outfeed Bin - Reclaim Log Infeed Deck - Bark conveyor and stacker - Bark Shredder - Progress 84" 6 Knife Chipper w/ 600 HP Motor - Progress Chip Screen: 7'x14' - Chip Blower and Truck Loading Conveyor - MCC Center

Nicholson Flat Drum Chipper 9'5' x 55" Includes: Trailer, AC power, belt conveyor, switch gear option. System chipped just over 120 truckloads

2011 Peterson Pacific Horizontal Grinder Power Source: Diesel Engine Mfr: Cat Engine Model: C27 Horsepower: 1000 Has approximate 9050 hours

The seller has confirmed that this 96" Precision chipper is in good working/running condition and is ready to load. This was not heavily run. This came out of a chip plant in WA. - Model 96.27 - Horizontal feed - Side discharge - 4-Knife whole log chipper - 8" thick chipper disc - Built in disc brake - Extended front shaft for hydraulic starter - Hydraulic starting motor - Side discharge pipe with motorized outlet adjustment - 27" maximum log diameter - Many spare parts and knives included - Average production rate: 125 tons per hour - No hydraulic pump - No motor - an 800HP one can be added for additional cost though - The photo's show the optional extended shaft and hydraulic starting motor which is a special feature.

Complete chip plant includes: - The infeed is 12’ above ground level. They were feeding it one log at a time with a shovel. - There is a single chain 12” wide leading to the debarker. - The debarker is a Salem 20” ring debarker with mcdiarmond controls. - From the debarker it goes through I think is a metal detector. It’s is enclosed, 8’ long with a belt conveyor. - 75’ of 3-strand chain that reduces to 2-strand chain for 35’ then goes to another 2-strand chain for 12’ then goes into the chipper. - The chipper is a Precision with 2- 400 hp high efficiency 3 phase motors. - From the chipper the chips drop onto a 42”x50’ inclined belt that leads to the 2 deck screen. The screen is 92”x20’ - The waste goes on a 9”x20’ incline belt and dropped into a truck. - The chips go out on a 3-strand 100’ conveyor (strands are 14” wide) to a radial stacker for loading trucks. The stacker belt is 42”x65’ - Chips can be redirected to blower unit system that will transport them to a rail siding to so they can be loaded into a rail area. It starts out with 75’ of 12” pipe running on the ground. Then it sweeps straight up to a height of about 24’ and goes 150’ to a siding across the county road. The chip loading facility is intact. - The hog is located back by where the logs are loaded onto the chain going to debarker. Here’s a list of the conveyors going back to the Kockums hog. It has a 24”x36” opening at the top. - Conveyors: 12”x100’, 12”x 25’, 12”x60’. All of these conveyors are 1 strand steel.

Precision 58" Chipper - Model 58-60-16 6 Knife 150 HP Motor