704-288-1904
Carolina Machinery Sales (CMS) works in the sawmill, pallet and woodworking industries. In addition to the buying and selling of used equipment, we work as brokers and take in machines on consignment. Give us a call today!
Industry
BioMass
122 Results Found
704-288-1904
Call for Price
175 KW -175 KVA 264 amps at 460v John Deere diesel powered 460v - 208v - 115v outlets housed in a container with ample access doors
Call for Price
This mill will be refurbished before it is shipped out. Can be configured for any application. Pellet Mill Line: Refurbished Model 39-1000 Including: - - Conditioner - - Feeder - - Drive - - Outlet box - - Discharge device - - Knife assembly - - 250 HP motor - - Hydraulic System - - Complete Roller Head - - MCC complete with starters - - PLC complete with programming - - Used Die 6mm - - Steel pellet mill base
Call for Price
This system is part of a project that never took off. The machines are new, never installed: - (6) Kahl 39-1000 Pellet Mills - 200 kW (268 HP) Motors: Two are wired at 460v, four at 575v. The other 4 can be rewound for a fee. Manufacturer specs (to be confirmed): Equipment List 6 Pelleting press type flat die 39-1000 Consisting of: 575V, 60 Hz 110 V AC 24 V DC - Divided cast iron case provided with cooling fins in the gear zone - Venting port in pellet mill middle part - Dust and inlet hood with product distributor and a venting port - Main shaft with thrust and radial bearings - Pan grinder head with scrapers and pan grinder rollers made of flame hardened steel - Temperature measuring of the die - Spring assembly, stainless steel - Spacer rings - Discharge unit with special scrapers - Worm gear turning in oil bath, worm wheel made of special bronze, hardened worm - shaft - Fan pulley - Oil pump to lubricate the main bearings, with oil filter, pressure device and thermometer 6 Three phase induction motor For the drive - Voltage: 575V - Motor power: 200 kW at 1,800 RPM - Drive shaft 90x170mm - Protection class: IP65, motor type B3 - Bearing suitable for 18 kN @ x=136mm - Stainless steel nuts and bolts - 12 tension rails • Two pieces per motor 6 Drive accessories for the pelleting press Consisting of: - V-belt pulley - V-belts - V-belt guard, steel construction, lateral walls with special air guiding plates, - indispensable for pelleting press cooling - 6 Roller gap control, type Distamat - For continuous adjustment of the roller head via the hydraulic nut Consisting of: - Hydraulic system for the press - Valve control - Electronic elements for transforming the measuring signals - Output: 4 – 20 mA = 0-5 mm - 6 Central slip ring seal air cleaning - For protection of the pan grinder roller slip ring seals during operation of the press Consisting of: - Air distribution with piping and coupling - Hose with central air connection to the pressed air 6 Oil coolers for the press Designed as oil-to-air heat exchanger Consisting of: - Oil-to-air heat exchanger - Oil pump - Hose connections - Temperature controller - 6 Press outlet box 39-1000 - Stainless steel design Equipped with: - Reversing flap - Inspection opening - Control socket - Aspiration connection, venting port - Pile up indicator - 1 Spare roller head for the 39-1000 - Spare, for easy and quick exchange of the roller head - 6 Automatic press control, type EAPR - Allen Bradley - For automation of pelleting line - Enclosed design, wired ready for connection according to IP 65 Consisting of: - Control and monitoring of all drives and units belonging to the line - Load dependent control of the pelleting press - Min/Max current monitoring of the pelleting press - Slippage monitoring of the pelleting press - Throughput control (t/h) - Visualization of the line on a graphic operator panel - Preselection of the process parameters at the OP - Fault and alarm messages at the OP - Start/s
Call for Price
Call for Price
Call for Price
Call for Price
This system was used at an old particle board facility. Seller thinks it is a MEC system. System starts with propane and then runs on dust. Includes burner, blower and piping.
Call for Price
Call for Price
Call for Price
In good condition. Has 50” opening. No drive motor but would take 100-200HP depending on material being run. No screen included. Very heavy weighs approximately 4 ton.
Call for Price
Very clean Newman G-200 Knife grinder. In good working order, grinds 17" on the inside and 20" on the outside.
Call for Price
Call for Price
Nice Newman G-280 that has been refreshed. Has extra cylinder wheels that come with it.
Call for Price
Call for Price
These machines were purchased new and removed from the current production line for a large hammermill. Ready to load. No conveyor available. - Newman SS24 - Two machines available. - 100 HP Motor on 600 V. Can be changed to 480 V.
Call for Price
Two Newman Shaving Mills Both mills have 2-heads Already pulled out of service and ready to ship.
Call for Price
Complete Chip Mill that is ready to be moved System includes: - Log Deck - Log Singulator - Control Room - Nicholson A5 Debarker - Peeled Log Outfeed Bin - Reclaim Log Infeed Deck - Bark conveyor and stacker - Bark Shredder - Progress 84" 6 Knife Chipper w/ 600 HP Motor - Progress Chip Screen: 7'x14' - Chip Blower and Truck Loading Conveyor - MCC Center
Call for Price
Nicholson Flat Drum Chipper 9'5' x 55" Includes: Trailer, AC power, belt conveyor, switch gear option. System chipped just over 120 truckloads
Call for Price
Complete Player Design Drying System - (2) Touch Screen Controllers - (1) PLC Control Box - (1) 12’ X 20’ Burner – 25 million BTU capacity with tempered sight glass that can run green chips/dust - (1) Burner Auger , Gearbox, and Motor - (1) Burner Blower Fan Assembly and Motor - (1) Player Single Pass Insulated Dryer Drum (12x50), 8” T section track, 28” Trunnions, Drive lubrication system, Sprocket, Chain and Gearbox / Motor (Drum rated for output material volume of 16,000 lbs per hour) - (1) Air Pro 48” Overhung Fan Assembly (ID Fan) (No Motor) ---- (Part# 12113601, Type-IERS615, Serial# 21136,) - (1) 200 HP motor for ID Fan - (1) Beck- Damper Adjustment Arm/Gearbox (ID fan comes with opposed blade inlet damper with a 300 ft-lb Beck actuator and armature) ---- (Model 11-209-155212-04-01---- 120V 1PH / 110VA ) - Piping and dampers for piping - Missing approximately 20’ of Dryer Drum Discharge piping - Missing approximately 20’ of Dryer Drum Recycle piping - System was rated at approx 9.25 Tons/hour