Box Opening 16" x 30" 20' Conveyor Included Custom Trailer Base

Hutto Shaving Mill Hydraulic cylinder to hold dow scrap material Infeed shoot: 16" x 30" 30 HP Motor

Hutto Shaving Mill 9' Box (2) Heads 50 HP Motors Outfeed conveyor

12" blade 7-1/2 HP motor 3 phase Foot Pedal control Left Hand machine

175 KW -175 KVA 264 amps at 460v John Deere diesel powered 460v - 208v - 115v outlets housed in a container with ample access doors

This mill will be refurbished before it is shipped out. Can be configured for any application. Pellet Mill Line: Refurbished Model 39-1000 Including: - - Conditioner - - Feeder - - Drive - - Outlet box - - Discharge device - - Knife assembly - - 250 HP motor - - Hydraulic System - - Complete Roller Head - - MCC complete with starters - - PLC complete with programming - - Used Die 6mm - - Steel pellet mill base

This system is part of a project that never took off. The machines are new, never installed: - (6) Kahl 39-1000 Pellet Mills - 200 kW (268 HP) Motors: Two are wired at 460v, four at 575v. The other 4 can be rewound for a fee. Manufacturer specs (to be confirmed): Equipment List 6 Pelleting press type flat die 39-1000 Consisting of: 575V, 60 Hz 110 V AC 24 V DC - Divided cast iron case provided with cooling fins in the gear zone - Venting port in pellet mill middle part - Dust and inlet hood with product distributor and a venting port - Main shaft with thrust and radial bearings - Pan grinder head with scrapers and pan grinder rollers made of flame hardened steel - Temperature measuring of the die - Spring assembly, stainless steel - Spacer rings - Discharge unit with special scrapers - Worm gear turning in oil bath, worm wheel made of special bronze, hardened worm - shaft - Fan pulley - Oil pump to lubricate the main bearings, with oil filter, pressure device and thermometer 6 Three phase induction motor For the drive - Voltage: 575V - Motor power: 200 kW at 1,800 RPM - Drive shaft 90x170mm - Protection class: IP65, motor type B3 - Bearing suitable for 18 kN @ x=136mm - Stainless steel nuts and bolts - 12 tension rails • Two pieces per motor 6 Drive accessories for the pelleting press Consisting of: - V-belt pulley - V-belts - V-belt guard, steel construction, lateral walls with special air guiding plates, - indispensable for pelleting press cooling - 6 Roller gap control, type Distamat - For continuous adjustment of the roller head via the hydraulic nut Consisting of: - Hydraulic system for the press - Valve control - Electronic elements for transforming the measuring signals - Output: 4 – 20 mA = 0-5 mm - 6 Central slip ring seal air cleaning - For protection of the pan grinder roller slip ring seals during operation of the press Consisting of: - Air distribution with piping and coupling - Hose with central air connection to the pressed air 6 Oil coolers for the press Designed as oil-to-air heat exchanger Consisting of: - Oil-to-air heat exchanger - Oil pump - Hose connections - Temperature controller - 6 Press outlet box 39-1000 - Stainless steel design Equipped with: - Reversing flap - Inspection opening - Control socket - Aspiration connection, venting port - Pile up indicator - 1 Spare roller head for the 39-1000 - Spare, for easy and quick exchange of the roller head - 6 Automatic press control, type EAPR - Allen Bradley - For automation of pelleting line - Enclosed design, wired ready for connection according to IP 65 Consisting of: - Control and monitoring of all drives and units belonging to the line - Load dependent control of the pelleting press - Min/Max current monitoring of the pelleting press - Slippage monitoring of the pelleting press - Throughput control (t/h) - Visualization of the line on a graphic operator panel - Preselection of the process parameters at the OP - Fault and alarm messages at the OP - Start/s

34” capacity knife grinder

14@ x 16” inlet 16” Round inlet no motor

MEC 12'x42' Triple Pass Drum Trunions Cyclone available

This system was used at an old particle board facility. Seller thinks it is a MEC system. System starts with propane and then runs on dust. Includes burner, blower and piping.

MEC 10x40 Single Pass Drum Trunions Controls

225 KVA 480 volt to 208Y/120

In good condition. Has 50” opening. No drive motor but would take 100-200HP depending on material being run. No screen included. Very heavy weighs approximately 4 ton.

Montgomery 100 HP Hammer Mill Includes: Outfeed conveyor and Infeed Hopper

Very clean Newman G-200 Knife grinder. In good working order, grinds 17" on the inside and 20" on the outside.

Nice Newman G-280 tub grinder. Everything functional just needs cleaned.

Nice Newman G-280 that has been refreshed. Has extra cylinder wheels that come with it.

Newman G200 Knife Grinder

These machines were purchased new and removed from the current production line for a large hammermill. Ready to load. No conveyor available. - Newman SS24 - Two machines available. - 100 HP Motor on 600 V. Can be changed to 480 V.