The frame is a massive, compact and solid casting which takes less floor space for its capacity The feed drive is built to stand up under the hardest kind of services The feed rolls are of such design that the advantages of the open side type of construction are combined with of the advantages of the inside The top and bottom head assemblies are of the most substantial construction The top head chip breaker is made of chilled cast iron section, each section being spring loaded and adjustable The side head spindles are short and of large diameter The side head chipbreaker moves in and out with the head and is also provided with an additional screw adjustment for close setting The bedding is continuous throughout the entire length of the machine

Used Yates American Model B-26, 24” Double Planer, 75HP top, 40HPBottom, top and bottom 10 knife cutterheads, on the fly top and bottom jointers, 3 phase 480volt electrics, slide out lower cutterhead, top fixed cutterhead, 3-3/4” thickness capacity, approx. 20HP hydraulic feed works, power bed raise and lower, sectional pneumatic chip breaker, top infeed/outfeed rubber rollers.

The seller has confirmed that this Yates American resaw was in working/running condition when it was pulled from production. It is ready to load! - Vertical resaw - All parts and blades included - Approximately 35 years old - 50-60HP - 440 amp

Planer Head Set Up Stand

220v 3 phase 2hp motor Controls work, motor runs and spindle turns Spindle raising mechanism has pin sheared in bevel gear. Includes overarm casting & mobile base.

Yuasa saw analyzer, great working condition comes with saw centers, magnifying camera and monitor.

Air Compressor Water Separator Single Phase 115V 16hz Good Condition

Recently removed from service Available immediately

Great Condition Recently Fully Serviced Profile Scrapers and Surface Scrapers No Premill/No Buffers

Brandt KDF 650 Edgebander

2007 Brandt KDF 680 Single sided Edgebander with Pre Milling and Corner Rounding

Brandt KDF 440 Highflex 1440 Edgebander APP. 1,200 hours on machine

Brandt KDN 210 Edgebander

2008 Brandt Edgebander 230Y/133V 3 Phase Currently in Production

Brewco 1600 Single Head Run Around

This system is no longer needed at the current facility. Ready for immediate removal! - Brewco Wolf Resaw - 4" Blade; 20'4" Long - 40" Bandwheels - 40 HP Main Motor - 10 HP Hydraulic Feed - McDonough Style Guides - Some spare blades - Head moves up/down, not the bed - Approximate dimensions: 9'L x 10'W x 6'H - Also available separately: - 8' Infeed Belt - 16' Outfeed Rollcase

Brewco 4-Head Resaw Seller has a hydraulic unit to go with the machine. No controls. Optional: System can be cleaned up and controls added PER SELLER: this machine is able to pass 7.75" cants it was purchased in Nelson BC 20 years ago it has not run since it is ready to go but has only on off switches and no motor starters per se I have not pulled the machine out to clean and paint and get ready to move it needs cleaned/ painted/ starters for 4-20hp motors/ small hyd unit for feed belt and feed rolls nice machine, I have not operated it but was running when I bought it and has been under cover since will need 5 starters, and a small hyd unit 5 hp, which i can provide this machine is easy to get ready if we have a commitment

Brewer 5-Head Resaw Return Belt

Brewer 3-Head Resaw Model # BR-3B8X12R

Brewer 2-Head Resaw Model: Diamond Eagle 2-HD Blade Size: 2" Year: 1997 Voltage: 480V 3ph Material Capacity: 15" width Serial #: 3478 Condition: Fully operational, no rust, Updated electrical panel. Spare Parts: 2" Blades Dimensions: 30" long x 12' wide New Bearing on one of the wheels. has 1 New Motor.