Gabbiani Double End Tenoner Available approx August 1, 2023 Can also be paired with a direct transfer to a [Homag DET](https://www.carolinamachinerysales.com/listings/4073344-used-2006-homag-fl20-double-end-tenoner) at the same site.

Gannomat Pro-Line 50 • Row of holes as well as line drilling in the SYSTEM 32 mm • 50 (2 x 25) holes in one drilling cycle

25 Spindles 10 Dowel inserters 2 Dowel hoppers Glue tank Water tank Left and right adjustable fences 4 Pneumatic clamps foot pedal controlControl Panel

Gardner Denver Air Compressor - 25 HP - Gardner Denver Air Dryer - 250 Gallon reservoir and stand

Laminating Rolls: 61" (155 cm) roll face with thermally conductive high release silicone surface; upper and lower main rolls internally heated; temperature controlled by state-of-the-art infrared sensors and digital PID controllers Laminating Opening: 1.5" (3.8 cm) maximum opening controlled with dual air cylinders. Laminating Material Uses heat activated and pressure-sensitive materials 0 - 55" (0 - 140 cm) wide on a 3" (7.6 cm) ID core Laminating Speeds 0 to 14.5 fmp (0 to 4.5 mpm) Post Lamination: Fanless cooling system provides uniform, filtered air for thermal shock without exposure to dangerous fan blades. Vinyl Transfer Complete roll to roll transfer, lamination, and edge trimming in one pass Safety Features • Two emitter-receiver photoelectric systems protect rolls from damage. • Emergency kick cables front and rear. • All electrical and moving mechanical parts are located in bolted cabinets • Four emergency stop buttons Installation Requirement 220 to 240 VAC, 50/60 Hz, 55A. 32 A per phase. Air: 2 cfm at 100 psi, minimum(0.5 m3 at 700 vPa)

GBN Explorer Pallet Nailer

Generac 200 HP Genset

Giben K305 Edgebander Manufacturer specs (to be confirmed): Standard Configuration Panel Thickness: 10~60mm Edge Thickness: 0.4~3mm Motor Power: 2.35Kw Maximum Curve Radius: 20mm Cutter Maximum Range: 50mm Working Pressure: 0.6 MPa Outline Dimension: 960 x 950 x 1000mm Gross Weight: 280Kg Voltage: 220-480V

ModelG4 49G4 510G4 512Table size2700 x 1300mm3100 x 1600mm3700 x 1600mmMax speed x/y/z80/80/30 m/min80/80/30 m/min80/80/30 m/minMain spindle18hp Max rotation speed24000rpm24000rpm24000rpm Vertical drills5 x 55 x 55 x 5 Rotation speed4500rpm4500rpm4500rpm Tool changer 8 position ride along Suction flow rate160m3/h160m3/h160m3/hDust extractionF200mm × 2 150mm x 2F200mm × 2 150mm x 2F200mm × 2 150mm x 2Overall size4500 x 10000 x 2500mm4500 x 12000 x 2500mm5000 x 13500 x 2600mmNet weight7100kg7500kg8000kg - The G4 Full line is a 3 axis cnc router designed for production needs in mind. - Standard 18hp main spindle with rotation of up to 24000rpms. - Drill block sizes: standard 5 x 5 and an optional 10 x 7. - Auto loading and off-loading helps create high efficiency and max parts output. Using a pusher bar with dust extraction and offload table with two additional ports to help maintain a clean shop and parts. - Standard features that separate the G4: auto-lubrication, meehanite cast ron table, fixed tool touch off device, and blast gate for dust extraction. - A ride along carousel type, tool changer with 8 tool capacity, mounted next to the spindle for fast and efficient tool change operations. - Optional 12 tool changer. - Optional auto label printing gantry or label printing mounted by the off-load table.

General Motors Power Takeoff Unit Detriot Diesel #5136548

Go Fast Single Head Resaw

Go Fast 5-Head Resaw Unit was cut into two pieces and can be put back together with a weld in the middle. Approx layout is 31' x 8'

Go Fast Resaw 15 HP Motor Put under power to test, never put into production.

Approximately 27" width capacity 1/2" - 3.9" diameter capacity 10 HP spindle motor 1800-3200 spindle speed 3 HP hydraulic feed PLC sequence controller

3" - 41" length capacity 1" - 3" square or round diameter capacity 15 HP spindle motor Spindle speeds 2250, 3200, 3525, 4625 rpm hopper feed

12' Arm 250 Lbs Capacity 4 HP Pump Per owner: head only turns horizonally

Gorbel 500 Lbs Ceiling Hoist

Weight18.57 tStandard tyres385/65R22.5 LRBucket capacity0.54 m³Mobile/CrawlerMTransport length8.4 mTransport width2.6 mTransport height3.6 mModel seriesVEngine manuf.VolvoEngine typeTAD572 VEEngine power160.3 kWDimension lxwxh982x854x992 mmDisplacement5.1 lRevolutions at max torque2300 rpmMax. torque910 NmNo. of cylinders4Cylinder bore x stroke110x135 mmEmission levelTier 4f

8 foot bar 11HP electric motor 489 volt 3 phase

6' x 14' capacity 4 HP motor 220 volt 3 phase stop system on base