BIESSE AKRON 420 EDGEBANDER --Machine Capacity: -- Thickness of banding rolls 0.4 - 3 mm (0.12"), Thickness of strips (HPL, veneer, solid wood strips) .0.4 - 6 mm (0.24"). Panel thickness 60 mm (2.4") max. & 10 mm min., Minimum panel length 140 mm.(5.5"). Minimum panel width 85 mm (3.3") --Equipped with: --÷ Feed/Glue Unit: automatic strip & coil feed magazine with robust shear-type 3 mm PVC guillotine. --÷ Hot Melt glue system, 10 Minute heat-up time with Teflon coated gluepot, digital thermostats with automatic kick-down when machine is in idle mode.÷ •1" Dia. glue applicator roller; pressure section with (1) large dia. "non-stick" coated drive roller & (2) chrome plated idle rollers with pneumatic positioning. --Workstations: --÷ Inclined travel Front & Rear End Trims (0.25 HP - 12,000 RPM motors), motors travel on (2) straight slides and pneumatic tilt 0° - 15° on horz. plane. --÷ Top & Bottom Fine Trims with motors (0.5 HP - 12,000 RPM motors), numeric readouts for easy setup. -- Top & Bottom Buffing Station (0.5 HP - 2,800 RPM motors), units tilt 0° - 30°. --÷ Feed Speed of 12 MPM (39 FPM), 3 HP feed drive. --Complete with: Insulated sound enclosure over all trim stations, extendible side panel support rail.

BIESSE - AKRON 440 AX Edgebander (w/Premill & Corner Rounding): -- Specifications: Material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood. -- Edge & Workpiece Capacity: 0.4 - 3 mm (0.016 - 0.12") Edge; 10 - 60 mm (0.39 - 2.36") panel thickness; 140 mm (5-1/2") min. panel length, and 85 mm (3.3") min. width. -- Working Units:Premilling Station: (2) 3 kW (4 HP) - 150 Hz, 9,000 RPM Motors; equipped with panel blowoff device and SIKO digital counters for adjustments. -- EVA Gluing Unit: Edge Feeding & Pressing Unit; automatic loading of tape in rolls and strips; quick-change glue pot system. -- Pressure Section: (1) Large 150 mm dia. driven & (5) idle pressure rollers. -- Feed Speeds: Operating feed speeds 12 & 18 MPM (39 & 60 FPM). -- Workstations: Double Motor End Trim; tiltable from 0° - 15°; each motor 0.8 kW (1 HP) - 12,000 RPM; sliding in a slicing motion on a 45° precision guide bar with oversized bearing blocks. -- Top & Bottom Trimming: (2) Motors 0.65 kW (0.87 HP) each; "Pro-Nesting" copiers; cutters R=2 mm. -- Fine Trim/Corner Rounding Unit: (2) Motors; each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with PVC, ABS, etc. material, and wood edge banding up to 3 mm max. edge thickness. -- Top & Bottom Flat Glue Scrapper: To remove potential glue squeeze out. -- Buffing Station: Top & Bottom, (2) motors, each 0.37 kW (0.5 HP) - 2,800 RPM. -- Operator Interface:Operator Control Panel, "HDI" High-Definition touchscreen control, Windows XP based. -- User-friendly graphic user interface with diagnostic and assisted maintenance. -- USB and Ethernet port; 1.44 MB floppy drive, automatic or manual startup. -- Complete with:High frequency motors (200 HZ): Padded sound enclosure. -- Top pressure beam with staggered double-row holddown wheels mounted on ball bearings. -- Actual Model is: BIESSE AKRON 440 AX

--at Auction, Seller Loading, Powered Inspection Available-- BIESSE AKRON 440 AX Edgebander, with Pre-Mill & Corner Rounding Specifications: - Material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood. - Edge & Workpiece Capacity: 0.4 - 3 mm (0.016 - 0.12") Edge; 10 - 60 mm (0.39 - 2.36") panel thickness; 140 mm (5.5") min. panel length, and 85 mm (3.3") min. width. Working Units: - Pre-Milling Station: (2) 3 kW (4 HP) - 150 Hz, 9,000 RPM Motors; equipped with panel blow-off device and SIKO digital counters for adjustments. - EVA Gluing Unit: Edge Feeding and Pressing Unit; Automatic loading of tape in rolls and strips; Quick change glue pot system. - Pressure Section: (1) Large 150 mm dia. driven & (5) idle pressure rollers. - Feed Speeds: Operating feed speeds 12 & 18 MPM (39 & 60 FPM). Workstations: - Double Motor End Trim; Tiltable from 0° - 15°, each motor 0.8 kW (1 HP) - 12,000 RPM; sliding in a slicing motion on a 45° precision guide bar with oversized bearing blocks. - Top and Bottom Trimming; (2) Motors 0.65 KW (0.87 HP) each - "Pro-Nesting" copiers - Cutters R=2 mm. - Fine Trim/Corner Rounding Unit: (2) Motors, each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with PVC, ABS, etc. material and wood edge banding up to 3 mm max. edge thickness. - Top & Bottom Flat Glue Scrapper, to remove potential glue squeeze-out. - Buffing Station: Top & Bottom, (2) motors, each 0.37 kW (0.5 HP) - 2,800 RPM. Operator & Machine Control: - Operator control panel, "HDI" High-Definition touch screen control Windows XP based. - User-friendly graphic user interface with diagnostic and assisted maintenance. - USB and Ethernet port. 1.44 MB floppy drive, automatic or manual startup. Complete with: - High-frequency motors (200 HZ): Padded sound enclosure: - Top pressure beam with staggered double-row hold-down wheels mounted on ball bearings. NOTE: Includes new Glue Pot, extra knives & misc. parts.

BIESSE AKRON 855 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- Material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood.0.4 - 3 mm (0.118"), Panel thickness 10-60 MM ( 0.39" - 2.36"), min. panel length 140 mm (5.5") and 85 mm (3.34") min. widthInfeed System Equipped with: -- Independent copying guide pads on each unit with manual adjustment & mechanical digital indicator.Pre-Milling Unit (FI-701) (2) 1.8 kW motors (2.5 HP), 12,000 RPM with Auto-Set device to ensure optimum positioning of the cutters according to the thickness of the panel being machine; -- "VC-710" edge feeding, gluing & pressing unit with automatic edge magazine for strip & coil stock; 3 mm PVC guillotine. -- "TEKNO-GLUE" System, Pre-Melt "QM-701" for quick heating & tank changing with floating & bi-directional glue roller applicator.Pressure Section: (1) Large motorized pressure wheel with clutch, plus (5) idle rollers, independent pneumatic pressure control & digital counters for quick edge thickness changeover.Edgebanding Workstations: -- Double Motor End Trim, tiltable from 0° - 15°, each motor 0.5 kW (0.6 HP) - 12,000 RPM; sliding in a slicing motion on a 45° precision guide bar with oversized bearing blocks. -- Top & Bottom Rough Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0° - 45° tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Top & Bottom Fine Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0° - 45° tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Multifunction 4-Motor Corner Rounding Unit "CR-202": (4) Motors, each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with PVC, ABS, etc. material and wood edgebanding up to 5 mm max. edge thickness. -- Top & Bottom Radius Scraping (PVC): Knives R = 2 mm, with mechanical digital indicators for precision setup, pneumatic exclusion of the unit from the machining line, PVC scrape collection box. -- Top & Bottom Flat Scraper (Glue): self-adjusting with copy wheels & flat insert knives, removing potential excess glue before buffing unit. -- Top & Bottom Oscillating Buffing Station: (2) motors, each 0.37 kW (0.5 HP) - 2,800 RPM. -- Top & Bottom Hot Air Blowers is made by two 2000 W hotair blowers to reactivate the color of PVC/ABS edges after the machining.The air temperature is adjustableFeatures & Feed: -- All cutting & trimming workstations have HF motors and enclosed by padded sound enclosure, top pressure is provided by staggered double-row holddown wheels mounted on ball bearings. -- Feed chain track speed : 10 - 14 - 20 MPM (33 - 46 - 65 FPM). -- Complete with:CNi PC w/Flat, Color "REAL TIME" graphic interface design on 17” flat screen (TFT) with high resolutio

BIESSE AKRON 855 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- Material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood.0.4 - 3 mm (0.118"), Panel thickness 10-60 MM ( 0.39" - 2.36"), min. panel length 140 mm (5.5") and 85 mm (3.34") min. widthInfeed System Equipped with: -- Independent copying guide pads on each unit with manual adjustment & mechanical digital indicator.Pre-Milling Unit (FI-701) (2) 1.8 kW motors (2.5 HP), 12,000 RPM with Auto-Set device to ensure optimum positioning of the cutters according to the thickness of the panel being machine; -- "VC-710" edge feeding, gluing & pressing unit with automatic edge magazine for strip & coil stock; 3 mm PVC guillotine. -- "TEKNO-GLUE" System, Pre-Melt "QM-701" for quick heating & tank changing with floating & bi-directional glue roller applicator.Pressure Section: (1) Large motorized pressure wheel with clutch, plus (5) idle rollers, independent pneumatic pressure control & digital counters for quick edge thickness changeover.Edgebanding Workstations: -- Double Motor End Trim, tiltable from 0ø - 15ø, each motor 0.5 kW (0.6 HP) - 12,000 RPM; sliding in a slicing motion on a 45ø precision guide bar with oversized bearing blocks. -- Top & Bottom Rough Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0ø - 45ø tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Top & Bottom Fine Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0ø - 45ø tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Multifunction 4-Motor Corner Rounding Unit "CR-202": (4) Motors, each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with PVC, ABS, etc. material and wood edgebanding up to 5 mm max. edge thickness. --Top & Bottom Radius Scraping (PVC): Knives R = 2 mm, with mechanical digital indicators for precision setup, pneumatic exclusion of the unit from the machining line, PVC scrape collection box. -- Top & Bottom Flat Scraper (Glue): self-adjusting with copy wheels & flat insert knives, removing potential excess glue before buffing unit. -- Top & Bottom Oscillating Buffing Station: (2) motors, each 0.37 kW (0.5 HP) - 2,800 RPM. -- Top & Bottom Hot Air Blowers is made by two 2000 W hotair blowers to reactivate the color of PVC/ABS edges after the machining.The air temperature is adjustableFeatures & Feed: -- All cutting & trimming workstations have HF motors and enclosed by padded sound enclosure, top pressure is provided by staggered double-row holddown wheels mounted on ball bearings. -- Feed chain track speed : 10 - 14 - 20 MPM (33 - 46 - 65 FPM). -- Complete with:CNi PC w/Flat, Color "REAL TIME" graphic interface design on 17” flat screen (TFT) with high resolution

BIESSE AKRON 855 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- Material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood.0.4 - 19 mm (0.118" - 0.75"), Panel thickness 10-60 MM (0.39" - 2.36"), min. panel length 140 mm (5.5") and 85 mm (3.34") min. widthInfeed System Equipped with: -- Independent units on each unit with manual adjustment & mechanical digital indicator.Pre-Milling Unit: (2) 1.8 kW motors (2.5 HP), 12,000 RPM with NC controlled Auto-Set devices to ensure optimum positioning of the cutters according to the thickness of the panel being machine; -- Edge feeding: Gluing & pressing unit with automatic edge magazine for strip & coil stock; 3 mm PVC guillotine. -- "TEKNO-GLUE" System, Pre-Melt for quick heating & tank changing with floating & bi-directional glue roller applicator. -- Pressure Section: (1) Large motorized pressure wheel with clutch, plus (5) idle rollers, independent pneumatic pressure control & digital counters for quick edge thickness changeover.Edgebanding Workstations: -- Double Motor End Trim, tiltable from 0ø - 15ø, each motor 0.5 kW (0.6 HP) - 12,000 RPM; sliding in a slicing motion on a 45ø precision guide bar with oversized bearing blocks. -- Top & Bottom Rough Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0° - 45° tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Top & Bottom Fine Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0ø - 45ø tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Multifunction 4-Motor Corner Rounding Unit: (4) Motors, each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with PVC, ABS, etc. material and wood edgebanding up to 5 mm max. edge thickness. --Top & Bottom Radius Scraping (PVC): Knives R = 2 mm, with mechanical digital indicators for precision setup, pneumatic exclusion of the unit from the machining line, PVC scrape collection box. -- Top & Bottom Flat Scraper (Glue): self-adjusting with copy wheels & flat insert knives, removing potential excess glue before buffing unit. -- Top & Bottom Oscillating Buffing Station: (2) motors, each 0.37 kW (0.5 HP) - 2,800 RPM.Features & Feed: -- All cutting & trimming workstations have HF motors and are enclosed by a padded sound enclosure, top pressure is provided by staggered double-row hold-down wheels mounted on ball bearings. -- Feed chain track speed: 10 - 14 - 20 MPM (33 - 46 - 65 FPM). -- Complete with:CNi PC w/Flat, Color "REAL TIME" graphic interface design on 17” flat screen (TFT) with high resolution.Actual model is BIESSE AKRON 855

BIESSE AKRON 855 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- Edge & Workpiece Capacity: 0.4 -15 mm (0.016" - 0.59"), Edge thickness, 14 - 65 mm (0.55" - 2.56"), Edge height, 10 - 60 mm (0.39" - 2.36"), Panel thickness:140 mm (5-1/2") Min. panel length, 85 mm (3.3") Min. panel width.Infeed Section: -- Pre-Milling Unit, "FI-701 Rectifies face to be edged before applying glue, Horizontal & vertical movement of (2) motors on linear guides, Independent automatic temporized intervention of (2) 1.8 kW (2-1/2 HP) 12,000 RPM Motors, Independent copying pads on each unit, Auto-set device to ensure optimum positioning of cutters according to the thickness of panel being machined. -- Edge Feeding, Gluing & Pressing Unit, "VC-710": with Automatic edge magazine for strip & coil stock, 3 mm (0.04") PVC Guillotine, "TEKNO-GLUE" System Includes: Pre-Melt, "QM-701", For quick heating & tank changing with floating & bidirectional glue roller applicator, and NC axis idle presser roller movement device. -- Pressure Section: (1) Large driven & (5) Idle rollers, Independent pneumatic pressure control, Programmable servo motor for quick edge thickness changeover, Feed speeds 10, 14 & 20 MPM (33, 46 & 65 FPM).Workstations: -- End (Edge) Trimming Unit, "IN-701-V": (2) 0.35 kW (1/2 HP) 12,000 RPM Motors, Automatic 4-position programmable chamfer from control panel (0°, 3.6°, 11°, 15°), Sliding in slicing motion on 45° precision guide bar with oversized bearing blocks. -- Superimposed Flush (Double Edge) Trimming Unit: "RS-701": Top & bottom, (2) 0.8 kW (1 HP) 12,000 RPM Motors with Superimposed motor position, 1° Tilt capability. Includes: Pneumatic exclusion device & Pneumatic top/bottom motor positioner. -- Tilting Top & Bottom Trimming Unit, "RI-701": (2) 0.65 kW (0.87 HP) 12,000 RPM Motors, For radius top & bottom fine trimming, Unit can be tilted 0° - 45°. Includes: NC axis multiple machining device. -- Corner Rounding Unit, "CR-200V": For corner rounding, top & bottom trimming on panel edge with synthetic material & wood edgebanding up to 5 mm (0.20") Maximum edge thickness. -- Edge Scraping Unit, "RB-701": For finishing rounded-off edges in PVC or ABS up to 5 mm (.20")thickness; Includes: Pneumatic unit lifter. -- Flat (Glue) Scraper, "RCC-700":Top & Bottom, removes potential excess glue before buffing unit. -- Buffing Unit, "SPL-700": Top & bottom. -- Hot Air Blower Unit, "PH-700", (2) STEINEL "2346" 2,000 W, Reactivates color of thick plastic.Complete with: -- PC-based control panel with 15" Color LCD monitor, HF (High-frequency motors on all cutting & trimming workstations. --Top pressure beam programmable via positioning motor, Top pressure provided by belt hold-down. -- 36" Diameter Coil table, Padded sound enclosure. -- Manuals (as pictured). -- Dimensions: 280" x 42" x 72" H. Weight: 3500 kG (7,750 Lbs).

BIESSE - AKRON 855, ...Edgebander with Premill & Corner Rounding (Loaded!)Specifications: -- Edge & Workpiece Capacity: 0.4 - 15 mm (0.016" - 0.59") Edge thickness; 14 - 65 mm (0.55" - 2.56") edge height; 10 - 60 mm (0.39" - 2.36") panel thickness; 140 mm (5-1/2") min. panel length; 85 mm (3.3") min. panel width. Infeed Section: -- Premilling Unit - "FI-701"Rectifies face to be edged before applying glue; horizontal & vertical movement of (2) motors on linear guides; independent automatic temporized intervention of (2) 1.8 kW (2-1/2 HP) - 12,000 RPM motors; independent copying pads on each unit, Autoset device to ensure optimum positioning of cutters according to thickness of panel being machined. -- Edge Feeding, Gluing & Pressing Unit - "VC-710"With automatic edge magazine for strip & coil stock; 3 mm (0.04") PVC guillotine; "TEKNO-GLUE" System includes: Pre-Melt "QM-701"; for quick heating & tank changing with floating & bidirectional glue roller applicator & NC axis idle presser roller movement device. -- Pressure Section: (1) Large driven & (5) Idle rollers, Independent pneumatic pressure control, Programmable servo motor for quick edge thickness changeover, Feed speeds 10, 14 & 20 MPM (33, 46 & 65 FPM).WORKSTATIONS: -- End (Edge) Trimming Unit - "IN-701-V"(2) 0.35 kW (0.5 HP) - 12,000 RPM Motors; automatic 4-position programmable chamfer from Control Panel (0°, 3.6°, 11°, 15°); sliding in slicing motion on 45° precision guide bar with oversized bearing blocks. -- Superimposed Flush (Double Edge) Trimming Unit - "RS-701"Top & bottom; (2) 0.8 kW (1 HP) - 12,000 RPM motors with superimposed motor position; 1° tilt capability; includes: Pneumatic exclusion device & Pneumatic top/bottom motor positioner. -- Tilting Top & Bottom Trimming Unit - "RI-701"(2) 0.65 kW (0.87 HP) - 12,000 RPM Motors; for radius top & bottom fine trimming; unit can be tilted 0° - 45°; includes: NC axis multiple machining device. -- Corner Rounding Unit - "CR-200V"For corner rounding; top & bottom trimming on panel edge with synthetic material & wood edgebanding up to 5 mm (0.20") max. edge thickness. -- Edge Scraping Unit - "RB-701"For finishing rounded off edges in PVC or ABS up to 5 mm (0.20") thickness includes: Pneumatic Unit Lifter. -- Flat (Glue) Scraper - "RCC-700"Top & Bottom, Removes potential excess glue before buffing unit. -- Buffing Unit, "SPL-700":Top & Bottom. -- Hot Air Blower Unit - "PH-700" - (2) STEINEL "2346" 2,000 W; reactivates color of thick plastic.Complete with: -- PC-Based Control Panel with: 15" Color LCD monitor, HF (High Frequency motors on all cutting & trimming workstations. Top pressure beam programmable via positioning motor; top pressure provided by belt holddown. 36" Dia. Coil table: Padded sound enclosure. -- Manuals (as pictured).Dimensions: 280" x 42" x 72" H. - Weight: 3,500 kG (7,750 Lbs.).

BIESSE - AKRON 855, ...Computer Controlled Production Edgebander.Features & Main Specifications: -- Computer-controlled interface for workstations with: Servos and pneumatic positioning devices. -- Programmable selections for "1-touch" changeover between edgebanding types and thicknesses. -- Edgebanding thickness: 0.4 - 19 mm Capacity. -- Min. panel: Width 85 mm & length 140 mm; thickness of 10 - 50 mm. -- Feed speed variable from 10 - 20 MPM, 3 HP feed drive.Frontend Equipped with: -- Premilling Unit with: (4) Positions for automatic changeover between premill settings, NC controlled. -- Strip & Coil Edge magazine: Automatic, "HD" shear-type guillotine. -- Top Pressure Beam: On-screen adjustable for height positioning. -- Hot-Melt Glue System: 12 Min heat up time, Teflon® coated gluepot; digital thermostats with automatic kick-down when machine is in idle mode. -- Side Pressure Section with: (1) Large dia. "non-stick" coated drive roller; (5) Teflon® plated idle rollers with Servo positioning, and NC controlled material thickness adjustment. Workstations: -- End Trimming Unit: Front & Rear (0.33 HP - 12,000 RPM motors), motors travel on (2) straight slides and pneumatic tilt 0° - 15° on horizontal. plane, NC controlled. -- Flush Trimming Unit: Top & Bottom with "Quick Change" motors, 1.0 HP - 12,000 RPM motors; digital readouts for easy setup. - 2-Position NC controlled. -- Flush/Bevel/Radius Trimming Unit: Multiuse top & bottom, 2-motor (0.3 HP - 12,000 RPM). Servo driven positioning of motors for different edge trimming setups. NC Controlled adjustment between profiles and positions. -- Corner Rounding Unit: 4-Motor (0.3 HP - 12,000 RPM motors) for trimming leading & trailing upper & lower edge/corners with "Fast Position"; can be used as a 2nd Top & Bottom fine trimmer, as well. -- Profile Scraping Unit: Top & Bottom for 2 mm or 3 mm thick PVC banding; digitals for horiz. adjustments. -- Flat Scraping Unit: Top & Bottom for glue and fine panel scraping. -- Buffing Unit: Top & Bottom (0.5 HP - 2,800 RPM motors), units tilt 0° - 30°. -- Hot Air Blower Unit: Top & Bottom edge reactivation station (2,000 Watt), hot air blowers with temperature adjustment. Complete with: -- Programmable processor for workstations & feed speed. -- Insulated sound enclosure over all trim stations with: Triple split dust & safety hood enclosure, industrial lights, and viewing windows. -- Extendable side panel support rail. -- 12 KVA - 240 Hz Digital frequency inverters.Includes: -- Used tooling on all workstations. -- Extra set of diamond tooling for premill unit. -- (1) Premill motor. -- NOTE: Chain pads have been replaced (2) years ago

BIESSE - JADE 240, ...Edgebander w/Premill & Corner Rounding -- Specifications: Edgebanding thickness: 0.4 - 8 mm (0.01" - 0.31"); Min. panel width 85 mm (3-1/2"); min. length 150 mm (5.9"); max. panel thickness 10 - 60 mm (0.39 - 2.36"). -- Premill Unit: (2) 1.8 kW (2.4 HP) - 12,000 RPM Motors; "AUTO-SET" device ensures optimum positioning of the cutters according to the thickness of the panel being machined; numerical readout; pneumatic exclusion when not needed. Workstations: -- End Trimming: Front & rear end trims: 0.8 kW (1.0 HP) - 12,000 RPM Motors; motors travel on 45° slides and pneumatic tilt 0° - 15° from the Control Panel. -- Flush/Bevel Trimming Unit: Top & bottom flush or bevel trims with: "Quick Change" Motors; 0.65 kW (0.8 HP) - 12,000 RPM motors; digital readouts for easy setup. -- Corner Rounding Unit: (2) Motors, 0.65 kW (0.8 HP) - 12,000 RPM for trimming leading & trailing upper & lower edge/corners with 2-position pneumatic set-up for corner rounding. -- Edge Scraping Unit: Finishing unit to eliminate previous machining imperfections; pneumatic exclusion from the machine control. -- Glue Scraping Unit:Top & Bottom scrapers for 3 mm thick PVC banding. -- Buffing Station: Top & Bottom.Operator & Machine Control: -- BIESSE "Smart Touch 7" + Windows Operating System: User-friendly touchscreen Control Panel for workstations; rotating Operator Control Panel w/keypad and LCD readout.Graphic 7" display touchscreen; high-resolution screen for defined and intuitive images and text; integrated 4 GB hard disk for filing media files and the programs back up.USB Port for managing in a simple and efficient way multimedia files, programs, and updates; Ethernet port for connecting the machine to the net.Complete with: -- Top pressure beam & motorized feed track with "anti-slip" "Quick Change" snap on 80 mm wide x 60 mm long rubber pads; low friction nylon graphite self-lubricating chain pads. -- Sound Enclosure & Panel Support: Over all trimming stations; industrial lights and viewing windows; extendable side panel support rail. -- Fixed feed speed at 39 FPM (12 MPM); 3 HP feed drive.Options include: -- Anti-Adhesive Unit:The unit applies an anti-adhesive liquid on the Top & Bottom surface of the panel. It is positioned before the Premilling Unit.The anti-adhesive liquid is applied with precision by means of injectors controlled by the machine control. -- Nesting Package:Allows trimming of premachined panels. -- Transformer:230 Volt autotransformer. -- Actual Model is BIESSE JADE 240

BIESSE ROXYL 6.0 ... Feature Loaded Edgebander with "AIR FORCE" & EVA (Hot Melt) Gluing Systems.Features: -- Latest Technology combines productivity, efficiency, and flexibility for all types of edgebanding material."AirForce" emits high temperature compressed air through a slot nozzle directly onto the reactive layer of laser banding. That layer is activated and bonds the banding to the panel fibers.This technology allows changes based on banding colors without any setup. Environmentally friendly providing a “clean - green” technology that eliminates glue and fumes, which becomes timely & important. -- In addition, it features a conventional EVA (Hot Melt) Gluing System to cover the full range of edgebanding processes in use today!Specifications: -- Edgebanding Capacity: Edge thickness for strips min./max. 0.4 - 22 mm (0.02" - 0.87"), coiled material from 0.4 - 3 mm (0.02 - 0.12"); panel thickness from 10 - 60 mm (0.39 - 2.36"), workpiece width min. of 85 mm (3.34"); workpiece length min. 140 mm (5.51"); feed speeds 10 - 14 - 18 - 20 MPM (33 - 46 - 59 - 65 FPM). -- Machine Controls: "Roxyl-Matic" Automated machine setup, MS/Windows XP Operating System, floppy drive, and 4 GB HD; USB port, keyboard, and mouse interface. -- Flat Screen (17") with color graphics interface: Programs can be easily created and recalled at will; Graphic interface makes programming easy; icons of each unit may be brought up on the screen to show the operator the status of the unit and the parameters, which can be programmed; Edgebander may be operated manually when required, without the necessity to write a program.Machine In-Feed Configuration: -- Pre-Milling Station "FL-502": (2) LH & RH Rotating NC controlled spindles with automatic center positioning. -- Edge Magazine: Automatic for processing coiled and strip edgebanding material + a (2) position vertical Coil Magazine Cart. -- Pressure Section: Servo controlled programmable pressure section with (1) large driven roller and (4) idle rollers.Gluing System: -- EVA (Hot Melt) "QM-705": Quick premelting granulate with glue roller applicator to cover conventional edgebanding material. -- AirForce "VC-710": High pressure, hot air system to reactivate special precoated edge material (commonly referred to as laser edge).Workstations: -- End Trimming Unit "IT90-S": Front & rear trimming motors, uni-point swivel 0° - 15° bevel, programmable pneumatic change-over from flush to bevel. -- Rough/Flush Trimming Unit "RS-100": Top/Bottom pre- or flush trimming motors -- Flush/Bevel/Radius Combination Trimming Unit "RF-400": Servo controlled, (4) Servo motors (one for horizontal tool position, one for tool up/down position); using combination bevel/radius/flush insert knives; pre-positioning of motors by pneumatic air cylinders. -- Anti-Adhesive "ADZ-700" Automatic Spray Unit with: Glue release agent preventing glue to adhere to workpiece's surfaces. -- Corner Rounding Unit "CR-202": (2) Motors for front/back corner

BIESSE EDGE - ROXYL 6.0 Edgebander, ...with (429) Hrs. Only!Specifications: -- Edgebanding thickness: 0.4 - 22 mm (0.02" - 0.87") Strip, 0.4 - 3 mm (0.02 - 0.12") Coil. -- Panel thickness 10 - 60 mm (0.39 - 2.36"), Min. panel width 85 mm (3.35"), min. panel length 140 mm (5.51"). -- Feed speeds: 10, 14, 18, & 20 MPM (33, 46, 59, & 65 FPM).Equipped with: -- "FI-502" Premilling Unit with: (2) Servo controlled spindles with Left-hand & Right-hand rotation & Auto-set device. -- "ADZ-700" Automatic anti-adhesive spray unit. -- 31" Dia. Coil table. -- Servo controlled infeed fence. -- Automatic edge Magazine for strips & coiled material. -- "VC-710" Hot melt glue system with: "QM-705" Premelt system for EVA. -- Servo controlled pressure section with: (1) Large driven roll & (4) idler rolls. -- PC-Based control with: 19" LCD Display, "ROXYL-MATIC" automated machine setup, MICROSOFT "WINDOWS" Operating System. -- 3-1/8” W Feed chain with: 3 kW (4 HP) Motor. -- Programmable top pressure beam with: Driven flat belt & 0.22 kW (1/3 HP) Motor. -- 19-1/2” Outboard support adjustment. -- Sound enclosure.Workstations: -- "IN-801" Front & rear end trim unit with 0° - 15° Bevel; pneumatic tilt & angle preselection from control. -- "RS-100" Top & Bottom rough/flush trim unit. -- "RF-400" Multifunction tilting Top & Bottom chamfering unit with: (2) HSD "ROTAX AT/MT 1073-120" 2.7 HP - 12,000 RPM Air-Cooled Electrospindles, (4) Servo motors: (2) For horizontal position & (2) for up/down position; Combination bevel/radius/flush insert knives, Pneumatic prepositioning of motors. -- "CR-202" 2-Motor Corner rounding unit. -- "RBK-503" Top & Bottom profile scraping unit with: 2-Axis Servo controlled knife positioning, 2 - 3 mm radius, for PVC edges; "RCC-701" Top & Bottom flat glue scraping unit with Pneumatic controlled in/out position. -- "SP-501" Top & Bottom buffing unit with: (2) 0.37 kW (1/2 HP) - 3,430 RPM Motors. -- STEINEL "3426" 2,000 W Hot air blowers.Complete with: -- Transformer.Dimensions of this specific machine with outboard support extended: 296" x 64" x 72" H.NOTE: Buy the TAYLOR "38A-M3" Return Conveyor (EXF# FR-010320) and keep the set together!

BIESSE SPARK 3.3 Edgebander (Compact)0.4 mm to 3 mm material thickness. Min. panel thickness 10 mm, max. panel thickness 40 mm. Min. panel width 90 mm, min. panel length 140 mm.Equipped with: -- 2 Liter Glue Teflon coated tank with quick heating system. -- Top pressure beam with manual adjustment through numerical read-out equipped with rubberized holddown wheels. -- Pneumatic Guillotine knife for automatic edge cutting with a max thickness of 3 mm with automatic “kickback” of the edge. -- Adjustable edge pressure unit with (2) rollers: 1st roller motorized with separate adjustable pressure system; 2nd idle roller with separate adjustable pressure system. Work stations: -- Double Motor End Trimming Unit - 2 tilting motors HF 0.5 HP each. -- Top and bottom Trim with (2) HF motors, 0.75 HP (0.55 kW) each and micrometric adjustment with numerical read-out. Cutters with 3 mm radius with (4) knives. -- Top and bottom Buffing station. -- Material feed speed 12 MPM (39 FPM).

BIESSE SPARK 3.3 Edgebander (Compact)0.4 mm to 3 mm Material thickness. Min. panel thickness 10 mm, max. panel thickness 40 mm. Min. panel width 90 mm, min. panel length 140 mm.Equipped with: -- 2 Liter Glue Teflon coated tank with quick heating system. -- Top pressure beam with manual adjustment through numerical read-out equipped with rubberized holddown wheels. -- Pneumatic Guillotine knife for automatic edge cutting with a max thickness of 3 mm with automatic “kickback” of the edge. -- Adjustable edge pressure unit with (2) rollers: 1st roller motorized with separate adjustable pressure system; 2nd idle roller with separate adjustable pressure system. Workstations: -- Double Motor End Trimming Unit - 2 tilting motors HF 0.5 HP each. -- Top and bottom Trim with (2) HF motors, 0.75 HP (0.55 kW) each and micrometric adjustment with numerical read-out. Cutters with 3 mm radius with (4) knives. -- Top and bottom Buffing station. -- Material feed speed 12 MPM (39 FPM).

BIESSE STREAM A 6.0 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING), High Production w/NC AXIS PACKAGE:Features: -- "NC AXIS PACKAGE": The machine adapts to the process being executed based on the edge's thickness and material.Machine management 100% touch with no need for external devices. Intelligent language management.Easy program management and usability with rapid transition from one machining operation to the next. Specifications: -- Edgebanding Capacity: Edge thickness for strips min./max. 0.4 - 22 mm (0.02" - 0.87"), coiled material from 0.4 - 3 mm (0.02 - 0.12");Panel thickness from 10 - 60 mm (0.39 - 2.36"), workpiece width min. of 85 mm (3.34"); workpiece length min. 140 mm (5.51");Feed speeds 12 - 18 - 20 - 25 MPM (39 - 59 - 65 - 82 FPM).Machine In-Feed Configuration: -- Pre-Milling Station:(2) 1.8 kW (2.4 HP) - 12,000 RPM Motors, LH & RH Counter Rotating Spindles, NC (servo) controlled with automatic intervention that guarantees a perfect base for gluing. -- Anti-Adhesive:Automatic Spray Unit with: Glue release agent preventing glue to adhere to work piece's surfaces. -- Infrared Heating Lamp:Preheating workpiece edge to ensure best possible surface adhesion quality of edgebanding material. -- Edge Magazine: Automatic 2-coil/position magazine for processing coiled and strip edgebanding material in real time. -- Pressure Section:Servo controlled programmable pressure section with (1) large driven roller and (4) idle rollers.Gluing System w/ Pre-Melter: -- EVA (Hot Melt), Quick premelting granulate with glue roller applicator to cover conventional edgebanding material. Workstations: -- End Trimming: Front & rear Linear end trimmer with Tilt Function for high speeds with (2) 0.8 kW (1.0 HP) - 12,000 RPM motors). The machine axis movement on linear tracks, allows the achievement of very high processing speeds.The copying and tracing system guarantees optimal finish quality also on high-gloss edges with film. -- Flush/Bevel Trimming Unit:Top & bottom flush or bevel trims with (2) "Quick Change" 0.65 kW (0.8 HP) - 12,000 RPM motors. -- Fine Trimming Unit: (2) 0.65 kW (0.8 HP) - 12,000 RPM Motors. (2) Servo motors for tool positioning (one for horizontal tool position, one for up/down tool position);Pre-positioning of motors by pneumatic air cylinders. while using a combination bevel/radius/flush insert knives;Absolute machining flexibility, thanks to the full adjustment of the machine according to the required edge thickness. -- Corner Rounding Unit: (2) 0.65 kW (0.8 HP) - 12,000 RPM Motors for front/back corner and upper & lower edge profiling.The controlled axis on the Corner Rounding unit supports the management of infinite machining settings. -- Profile Scraping Unit:Top/Bottom 2-axis NC programmable knife positioning (i.e. 2 - 3 mm radius) for PVC edges. -- Glue Scraping Unit: Flat, top/bottom, digital positioning indicators, pneumatic controlled for in/out position. -- Buffing Station: Top & Bottom buffing motors 0.37 kW

BIESSE STREAM B1 9.0 ... Production Edgebander with Pre-Milling & Corner Rounding Specifications: -- Capacity, 0.4 - 15 mm edge thickness cap., min. panel width 100 mm, panel thickness 10 - 60 mm, min. panel length 150 mm. -- Pre-Milling Unit: With jump control & side copying unit for managing warped panels, 2-position infeed fence, digitals readouts. -- NC 410 Controller with: Graphic interface on MS-Windows 2000 Professional, 32-bit operating system; high resolution LCD color screen, unlimited" number of working programs, each with functions for remote control of processing units; fault diagnostic, bar code reader adaptable; etc. -- Automatic (2) coil vertical feed magazine for coil material up to 3 mm thickness with automatic changeover. -- Patented Glue System w/pre-melt, large separated granular hopper for easy filling & high gluing capacity, with roller applicator (reversible); -- Pressure Section, (1) large driven pressure roller & (6) pneumatic secondary pressure rollers. Workstations: -- End Trimming:Double motor front & rear linear end trimming unit "IT 46" (0.4 HP/0.3 kW - 12,000 RPM motors ea.); pneumatic chamfer setting, 0° - 15° adjustable. --÷ Pre/Rough Trimming:Top & bottom "RS 10" (1.75 HP/1.3 kW - 12,000 RPM motor ea.), pneumatic exclusion & positioning from control panel. -- Radius/Bevel Trimming:Top & bottom (0.87 HP/0.65 kW - 12,000 RPM motor ea.), tiltable 0° - 30°, pneumatic exclusion from operator panel. -- Corner Rounding:4-Motor for leading & trailing edges. -- Profile Scraping Unit:Top & bottom with collection box. -- Flat Glue Scrapers:Top/bottom to remove potential glue squeeze-out. -- Buffing Unit:Top/bottom, ozcillating/tilting "SZ 30" w/pneumatic exclusion control from control panel & 0.67 HP/0.5 KW- 1,400 RPM motors; -- Hot Air Unit:Top/Bottom hot air blowers to reactivate/smooth heavy pvc radiused edges. Complete With:- Motorized top pressure beam with powered V-belt hold-down, electronic positioning by NC controller.- 80 mm wide Heavy Duty feed chain w/rubber pads, - 4 HP feed drive for feed variable speeds of 26 - 78 FPM. - Pneumatic Pre-set Stop System for most adjustments via the control panel on top & bottom trim, fine trim, and scraper station,- Electronic frequency inverter, electronic DC brakes on all trim motors.- Sound cabins for all trim work stations, outboard panel support.Note: Actual Model ... BIESSE STREAM B1 9.0

BRANDT F-13 Top & Bottom TrimmerFor simultaneous top & bottom flush/radius trimming of the oversized edgeband on straight & shaped workpieces with inside-and-outside radii.Specifications: -- Top & Bottom edge trim PVC, HPL and veneer edgings, up to 3 mm max. thickness. -- Manually operated, 1/2" - 2-1/4" panel thickness, 1-3/8" min. inside radius. -- Features: Independent top & bottom trim heads (0.5 HP - 11,800 RPM motor each); -- Built-in air jet blowoff device, 31" x 48" table size, and dual foot pedal controlNOTE: Intermittent fault in the control panel, which will require replacement.

BRANDT AMBITION 1120 FC (aka KDF 120 C) (EDGEBANDER WPRE-MILL & CORNER ROUNDING): -- Specifications: Edge & Workpiece Capacity, 0.4 - 3 mm Edge cap., min. panel thickness 8 mm (0.3"), max. panel thickness 40 mm (1.57"), min. panel width 70 mm (2.75"). Min panel length: 140 mm (5.5")Line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all workstations. Auto in-feed stop to insure proper spacing between panels. Equipped with: -- Pre-Milling Station:(2) motors @ 0.75 kW (1.0 HP) ea., 12.000 RPM, LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges. Equipped with diamond cutter heads. -- Gluing Section:Automatic magazine for strip & coil (large coil table 800 mm diameter to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, Pressure Section with (1) large drive plus (2) idle rollers "pneumatically controlled." Hot Melt granulate quick heat-up glue system. Workstations: -- End Trimming: 2 x 0.18 kW (1/4 HP), 12,000 RPM motors, THK guided, chamfers 0° - 15°. -- Flush/Bevel/Radius Trimming:2 x 0.55 kW (0.75 HP),12,000 RPM motors with insert knives for 3 mm PVC radius. cutter-heads, bevels 0° - 15°. -- Corner Rounding Station:1-Motor (4-corners) contour trim for profile corner rounding, 1 x 0.35 kW (0.5 HP), 12,000 RPM motor, with insert knivesFor 3 mm PVC radius w/digital read-out set-up and pneumatic change-over from thin to thick PVC edge tape. -- "Quick-Change" Profile Scraping Unit:Top & bottom for 2 - 3 mm radius, pneumatically controlled blow-off nozzles. -- Flat Scraping Unit:Top & bottom flat scraping units with copy wheels to remove residual glue squeeze-out. -- Operator & Machine Control: "ECO Plus Control", easy operation with simple menu format; large LCD display and integrated line control via keypad.Production readiness displayed by traffic light indicator with ability to adjust units quickly thanks to direct access via ctrl keys. Intuitive, user-oriented navigation with a clear overview of the help and assistant functions, including the glue pot temperature or troubleshooting in plain text. -- Complete With: &#9679 Trim stations have HF motors w/electronic brakes &#9679 Fixed feed chain track speed of 8 MPM (26 FPM) &#9679 2 HP feed drive &#9679 208/230/440/480v, 3ph Transformer &#9679Sound/Safety Enclosure &#9679 Adjustable Out-Rigger Support &#9679 Used tooling. -- Actual Model is BRANDT AMBITION 1120 FC (aka KDF 120 C)

BRANDT AMBITION 1200 (aka KDN-200) EDGEBANDER (Compact): -- Specifications: 0.4 - 3 mm (1/8") Edge thickness cap., 8 - 50 mm (0.3" - 2") panel thickness, 60 mm (2.3") min. panel width and 140 mm (5-1/2") min. length. -- Hot Melt granulate glue system with "Quick Melt" start-up (10 - 12 Min heat-up) with reversible rotation glue applicator roller and automatic reduction glue temperature adjustment (when idle drops to 150°, 2-1/2 Min to re-activate). -- Automatic feed magazine, coil stock feeds automatically with guillotine cutoff, all strip stock are fed automatically through strip feed magazine. -- 3-Roller pressure section (1st driven, next (2) idle) w/electronically controlled and feed speed synchronized drive rollWorkstations: -- Vertical travel double-motor front & rear end trim with tilting of 0° - 15° cap. (0.24 HP - 12,000 RPM motors); -- Top & Bottom Multifunctional Trimming Units (0.36 HP - 12,000 RPM motors), bevel 0° to 15°. -- Top & bottom buffing unit (0.15 HP - 2,750 RPM motors).Equipped with: -- Operator control panel at eye-level. -- Automatic height adjustment with top pressure beam for all work stations. -- Digital height indicator on hold-down beam. -- Electronic motor brakes on trimmers. -- Feed speed of 30 FPM.Includes: 200 Hz Electronic frequency inverter, used tooling, sound enclosure w/window, and operators manual. -- Actual Model is BRANDT AMBITION 1200 (aka KDN 200).

BRANDT - AMBITION 1440 (KDF-440 C), ...EDGEBANDER (W/PREMILL & CORNER ROUNDING): -- Specifications: Edge & workpiece capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") panel thickness, 160 mm (6.30") min. panel length, 70 mm (2.76") min. panel width.Equipped with: -- Adjustable Infeed Fence: Manual adjustment. -- Joint Trimming/Premilling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, left-hand & right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. -- Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting; 0.4 - 8 mm (0.016" - 0.31") strip thickness; 3 mm (0.12") PVC max. coil thickness. -- Hot Melt Glue Application Unit: 6 - 10 kG/Hr (13 - 22 Lbs/Hr) Melting capacity (depending on glue type). -- Pressure Zone: (1) Driven & (2) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speeds: 8 - 14 MPM (27 - 45 FPM); 11 MPM (36 FPM) when contour trimming. -- BRANDT "POWERTOUCH" Control with: 21" HD LCD Touch Screen Monitor.Workstations: -- Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors with 0° - 15° automatic chamfer, pneumatic adjustment & activation/deactivation of edging material overhang using "POWERTOUCH" control. -- Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt with Horizontal & Vertical Tracing wheels, Brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover with (3) Positioning options: Profile 1, Profile 2 & Flush Trimming. -- Multifunctional Trimming Unit: (2) 0.4 kW (1/2 HP) - 12,000 RPM Motors for leading & trailing edges vertical corner rounding of panels, Servo motors for positioning of work unit & horizontal copy wheels. Either radius or chamfer cutters can be mounted, 3 mm (0.12") max. edge thickness. -- Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"); Servo control positioning of vertical & horizontal copy wheels; PVC scrape collection box, pneumatic adjustment using "POWERTOUCH" control, pneumatic disengagement. -- Top & Bottom Glue Scraping Unit: Flush on panel surface with floating insert knives. -- Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) - 2,750 RPM Motors.Complete with: -- Rubber padded feed chain w/top idle holddown rollers; 1.5 kW (2 HP) feed motor; 32" diameter coil table; padded sound enclosure. -- Actual Model is BRANDT Ambition 1440 (KDF 440 C).