和成天下槟榔200 For Sale

UNIMAK GS140-S Single Sided Hot Melt Glue Laminator4-Foot Wide Hot Melt Glue Spreader for PUR and other Hot Melt Adhesives. Panel Types: MDF, Particleboard, door spar, XPS and Polystyrene sandwich panels. All kinds of panels where adhesive application is required.Glue Types: Polyurethane Hotmelt (PUR) glue. Unfilled EVA.Pressure Sensitive Foil Types: As roll material - PVC, P.P., finish foils and CPL foils. As sheet Stock - Veneer, PVC, laminate, acrylic sheets and door surfaces. Working Speed : 5 - 25 m/Min (16.4 - 82 FPM).Technical Specifications: -- Max. External Working Temperature: 180 ° C (365° F), Chromed Roller. -- Working Width: 200 - 1,400 mm (7-7/8" - 55"). -- Board Thickness: 4 - 210 mm (1/8" - 2-1/4"). -- Upper Spreader Roller - 240 mm (9-1/2") diameter, Silicone Coated. -- Upper Dosing Roller: 215 mm (8-1/2") dia., Chromed. -- Lower Transport Roller: 240 mm (9-1/2") diam., Silicone coated. -- Total Power: 15 kWMelter and Hose are not Included, they are optional and can be quoted separately or purchased locally.

UNIMAK 160-S 5-Foot Wide Single-Sided Hot Melt Glue Spreader for Hot Melt Glue including PURHot Melt Glue Spreader for PUR and other Hot Melt Adhesives. Panel Types: MDF, particleboard, door spar, XPS, and polystyrene sandwich panels. All kinds of panels that adhesive application is required.Glue Types: Polyurethane hot melt (PUR) glue. Unfilled EVA,Pressure Sensitive Foil Types: As roll: PVC, P.P., finish foils and CPL foils As sheet Stock: Veneer, PVC, laminate, acrylic plates and door surfacesWorking Speed: 5 - 25 meter/Min (16.4 - 82 FPM)Technical Specifications: -- Max. External Working Temperature: 180 ° C (365° F) - chromed roller. -- Working Width: 200 - 1,600 mm (7-7/8" - 63"). -- Board Thickness: 4 - 40 mm (1/8" - 1-5/8"). -- Upper Spreader Roller, Silicone Coated and Ø 240 MM (9-1/2"). -- Upper Dosing Roller: Ø 215 MM – Chromed (8-1/2"). -- Lower Transport Roller: Ø 240 MM – Silicone coated. -- Total Power: 15 kWMelter and Hose are not Included, they are optional and can be quoted separately.

200 gal vertical air tank, good condition

200 Amp Fused Disconnect

200 gallon Vertical Air Tank, Mounted on Stand

US CONCEPTS CHB 12 HauncherThe CHB-12 Hauncher-Notcher is designed to notch along the edge of the board or across the end.Typical applications: Box joints, finger joints, bee boxes, hinge notches, coping, profiling in furniture and window industries, decorative cuts, beaded frame cabinets, toe kick notches, etc. Equipped with: a 40 mm horizontal spindle that moves up hydraulically past the table with the clamped material. -- A backup board in the table and climb cut ensure the clean-cut, even on cross grain. -- Material air clamps and spindle motion are actuated by a foot switch. Specifications: -- Spindle Dia. 40 mm, Spindle Length 12". (Also available in 16" & 20" capacities) supported on both ends; -- Max. Cutter Dia. 10" (254 mm); max. Cutting Depth 2-1/2" (64 mm); max. Material Stacking Height 8" (200 mm). -- Spindle Speed 4,300 or 6,200 RPM; Feed Speed (Air/Oil) 0 - 25 FPM; 15 HP motor; Dust Outlet 2 x 6" (150 mm).Complete with: -- (2) Air Clamps, Back Fence, Side Pivot stop, and Stop Bar. -- Table Size 36" x 16"; Machine Weight 1,650 Lbs (750 kG). -- OPTIONS: Electric; 20 or 25 HP motor; Additional Air Clamps; Additional Side Stop; Center Fence mounted to the Table; Horizontal Clamps; Extended Stop Bar. -- Other Options: Fixture for 45° Cut (Mitered cabinet Doors or Stretcher Bars).

US CONCEPTS CHB-16 HauncherThe CHB-16 Hauncher-Notcher is designed to notch along the edge of the board or across the end.Typical applications: Box joints, finger joints, bee boxes, hinge notches, coping, profiling in furniture and window industries, decorative cuts, beaded frame cabinets, toe kick notches, etc. Equipped with: a 40 mm horizontal spindle that moves up hydraulically past the table with the clamped material. -- A backup board in the table and climb cut ensure the clean-cut, even on cross grain. -- Material air clamps and spindle motion are actuated by a foot switch. Specifications: -- Spindle Dia. 40 mm, Spindle Length 16". (Also available in 20" capacity) supported on both ends; -- Max. Cutter Dia. 10" (254 mm); max. Cutting Depth 2-1/2" (64 mm); max. Material Stacking Height 8" (200 mm). -- Spindle Speed 4,300 or 6,200 RPM; Feed Speed (Air/Oil) 0 - 25 FPM; 15 HP motor; Dust Outlet 2 x 6" (150 mm).Complete with: -- (2) Air Clamps, Back Fence, Side Pivot stop, and Stop Bar. -- Table Size 42" x 16"; Machine Weight 1,650 Lbs (750 kG). -- OPTIONS: Electric; 20 or 25 HP motor; Additional Air Clamps; Additional Side Stop; Center Fence mounted to the Table; Horizontal Clamps; Extended Stop Bar. -- Other Options: Fixture for 45° Cut (Mitered cabinet Doors or Stretcher Bars).

Brand New Hot Melt Adhesive Melter that can be adapted to your existing equipment.The 200 L Drum Unloader is designed for the application of any type of adhesive delivered in 200-liter drums, the EDrum Series Unloaders are extremely versatile and include several customizable options that adapt to each user's specific requirements.Features: Safer working environment with optional platen protection system and vent hood. Reduced downtime related to drum changes with new drum fastening system. Customizable to specific users needs Integrated grammage dosing control. Teflon encapsulated seals.Technical Specifications: System 200L flat platen or 200L finned platen Drum capacity 200 liters Melting capacity flat platen system 60 Kg/Hr Melting capacity finned platen 130 Kg/Hr Max. number of pumps is two (2) Working temperature 30 - 240° C (86 - 464° F) Max. working viscosity 100,000 CPS Max. working pressure 100 Bar Electrical consumption 24 kWWe can also supply a selection of accessories to integrate & fit the Bulk Melter to your existing equipment, including: RTD hot melt hoses Slot Die applicators Edge Bander PUR retrofit Slot Die kits Manual and Automatic dispensing valves Mounting bracket packages Solid State Pattern Control Systems In-Line Filters Replacement parts for competitive systemsHose sizes will vary depending on your application; please speak with our sales representatives regarding that, below are a few Options: 8' long - #6 core 12' long - #6 core 16' long - #6 core 8' long - #8 core 12' long - #8 core 16' long - #8 core 8' long - #12 core 12' long - #12 core 16' long - #12 core Delivery from date of order approximately 10 WeeksAll parts and service are based in the USA out of Cincinnati Ohio.

Brand New Hot melt adhesive melter that can be adapted to your existing equipment.The 20 L Pail Unloader is designed for the application of any type of adhesive delivered in 200-liter drums, the B-Pail Series Unloaders are extremely versatile and include several customizable options that adapt to each user's specific requirements.Features: Safer working environment with optional platen protection system and vent hood. Reduced downtime related to drum changes with new drum fastening system. Customizable to specific users needs Integrated grammage control. Teflon encapsulated seals.Technical Specifications: System 20L flat platen or 20L finned platen Drum capacity 20 liters Melting capacity flat platen system 8 Kg/h Melting capacity finned platen 25 Kg/h Max. number of pumps is one (1) Working temperature 30 - 240 Centigrade (86 F - 464 F) Max. working viscosity 100,000 cps Max. working pressure 100 bar Electrical consumption 8 KwWe can also supply all of your need's for accessories to make the Fit Up to your equipment including: RTD hot melt hoses Slot die applicators Edge Bander PUR retrofit slot die kits Manual and automatic dispensing valves Mounting bracket packages Solid state pattern control systems In-Line filters Replacement parts for competitive systemsSince Hose sizes will vary depending on your application please speak with our sales representatives regarding that, below are a few Options: 8' long - #6 core $461.00 12' long - #6 core $646.00 16' long - #6 core $750.00 8' long - #8 core $748.00 12' long - #8 core $957.00 16' long - #8 core $1,065 8' long - #12 core $835.00 12' long - #12 core $916.00 16' long - #12 core $1,158.00Delivery from date of order approximately 8 WeeksAll parts and service are based in the USA out of Cincinnati Ohio.

The 200 L Drum Unloader is designed to apply any type of adhesive delivered in 200-liter drums. The EDrum Series Unloaders are extremely versatile and include several customizable options that adapt to each user's specific requirements. -- Features: Safer working environment with optional platen protection system and vent hood.÷Reduced downtime related to drum changes with new drum fastening system.÷Customizable to specific users' needs÷Integrated grammage dosing control.÷Teflon encapsulated seals. -- Technical Specifications:÷System 200L flat platen or 200L finned platen÷Drum capacity 200 liters÷Melting capacity flat platen system 60 Kg/Hr÷Melting capacity finned platen 130 Kg/Hr÷Max. number of pumps is two (2)÷Working temperature 30 - 240° C (86 - 464° F)÷Max. working viscosity 100,000 CPS÷Max. working pressure 100 Bar÷Electrical consumption 24 kW -- We can also supply a selection of accessories to integrate & fit the Bulk Melter to your existing equipment, including:÷RTD hot melt hoses÷Slot Die applicators÷Edge Bander PUR retrofit Slot Die kits÷Manual and Automatic dispensing valves÷Mounting bracket packages÷Solid State Pattern Control Systems÷In-Line Filters÷Replacement parts for competitive systemsNear brand New Hot Melt Adhesive Melter that can be adapted to your existing equipment. Only used on 4 - drums

VECOPLAN RG 70/200K Shredder with Steel Belt Conveyor & Dust CollectorSpecifications: -- Hopper Opening: 70″ x 80″ -- Hopper Volume: 4 – 6-1/2 Cubic Yards -- Main motor: 200 HP -- Rotor diameter: 20″ -- Number of cutters: 84 (triple row) -- Size of cutters: 40 mm x 60 mm -- Screen size: Holes 2″ -- Rotor speed: 145 RPM -- Rotor diameter: 20″ -- Hydraulic Feed Ram: 10 HP - 2-Speed -- Throughput: 2,000 – 28,000 Lbs/HrEquipped with: -- 10 HP Motor Dust Collector -- 48″ W kW SCHMIDT Shredder Infeed Conveyor w/ 20′ pit section

VECOPLAN VAZ 145/250 SINGLE SHAFT SHREDDERSpecifications; -- 575v 3 Phase --Hopper opening: 57 x 98.58 in. --Rotor width: 98.58 in. --Rotor Diameter: 14.56 in. --Rotor speed: 200 rpm --Main Drive- Electric motor with power belt drive --Gear ratio: i=5 --100 hp --Motor current: 192 A --Dimensions:- Shredder: 184"L X 141"W X 108"T- Chute: 160"L X 128"W X 76"T- Panel: 73"L X 50"W X 25"T

This listing Is for a complete line that consists of a Flow Coating line that feeds into a cross transfer oven and back out on to an outfeed conveyor making a 180 degree circuit. The heat exchanger needs to be heated by means of a hot water boiler or similar. Maximum Part width: 305 mmSpeed range: 2 - 10 m/min.Pos. 1 - FEEDING BELT CONVEYOR:For feeding the batches into the flowcoater, Belt with marked area to built a gap for the angle transfer, Technical Data: length: 2300 mmPos. 2 - IMPREGNATION MACHINE VEN FLOW:For flowcoating of profiles in continious production with a waterbased impregnation (viscosity similar to water)The material is is sprinkled on the surface and remains for appr. 10 seconds. After this time a high pressure air knife nozzles will blow the acess materialfrom the surface. The whole cabin is built with fall to the side to collect the rest of the material. It is reused after passing a filter system. The cabin is built of stainless steel. The blowing off of the access material by air knife is effected by a high pressure fan.The machine comprises:1 conveyor system with spray protected roller system length 3000 mm1 sprinkling zone with two nozzle systems adjusted to reach the whole surface of the workpiece. length: 200 mm1 penetration area length ca. 1000 mm time of residence ca. 10 sec1 blowing zone with adjustable knife nozzles air supply with high pressure fan air flow adjustable by frequency converter length ca. 1000 mmair speed ca. 40 m/sec. material supply to supply the two sprinklers with fluid and collector for recovered material.workpiece tolerances:twist: max. 1° on the whole length, straightness max. 0,5mm deviation/m in horizontal and vertical weight distribution: evenly on whole length coating material: waterbased impregnation. Unstable components can not be repositioned when tilted.Pos. 3 - MOULDING ANGLE TRANSFER VEN TRANS 90°conveying from lengthwise direction to crosswise, comprising:1 excenter-transfer arms integrated into the driven infeef roller conveyor. The tacted transfer system allows a minimum distance between the singlemouldings on the following cross transfer system.Technical Data:length of roller conveyor: 4500 mmroller pitch: 185 mmnumber of transfer arms: 22spacing 185 mmtacting cycle: max. 30/min.Pos. 4 - MOULDING CROSSWISE V-BELT CONVEYOR:Mouldings are conveyed by means of various v-belts along the system. The unit is fitted with an insulation cover between the conveyor. A drying tunnel is fitted on top of the unit.Technical data:length: 4000 mmoperating width: 4200 mmnumber of belts: 22distance of belts: 185 mmoutfeed prepared for an additional angletransfer:position of driving shaft in the middlegaps for passing of the carriers of the angle transferPos. 5 - JET DRYING TUNNEL 70 °C:Made of sandwich elements with fire preventing insulation material. The even distribution of air over the full operating width is reached by using slot nozzles on the full width of the tunnel. One combined heating-, fan

VICKERS - 60 HP, ...Hydraulic Power PackHydraulic Power Pack with all the bells and whistles: VICKERS Pump & valves and a SENTINEL tank. Hydraulic Power Pack Includes -- Variable volume, pressure compensated, piston pump. -- Capacity: 8 Cu. in./rev. -- Pressure rating: 4,000 PSI. -- Driver: 60 HP Electric motor; 1,750 RPM. -- Reservoir: 200 Gal. -- Kidney Loop: Gear pump w/filter. -- Air-cooled Heat Exchanger. -- Return line filter. -- Liquid lever switch and temperature switch. -- Fluid inspection window.NOTE: This item was installed earlier but never used. Year of manufacturing is approximate.

Viet Opera 5-4.3 RRRR, (4) Head Wide Belt SanderCalibrating Sander (89 Hours)53″ wide cap. - Drum, Drum, Drum, DrumHead Configuration1st Head: 9″ Helical grooved steel drum powered by a 22 kW or 29.5 HP motor.2nd Head: VARIABLE SPEED (via VFD) 9″ helical grooved rubber drum powered by a 18.5 kW or 25 HP motor. 3rd Head: VARIABLE SPEED (via VFD) 11″ helical grooved rubber drum powered by a 15 kW or 20 HP motor. 4th Head: VARIABLE SPEED (via VFD) 11″ helical grooved rubber drum powered by a 15 kW or 20 HP motor.5th Station: Dust brush powered by a 1.27 kW or 1.7 HP motorSpecifications -- The durometer does get softer from head 2 to 3 and then from head 3 to 4. -- It has 53″ width capacity and a 200 mm or 7.87″ thickness capacity. -- Right above the machine's infeed, you will find inspection LED lighting, a digital thickness calibration unit, and a wireless Mitutoyo Digimatic Caliper that communicates with the Opera’s operating system. -- The vacuum bed is powered by an 11 kW or 15 HP blower under the sander to save space. -- The feed mat is powered by a 5.5 kW or 7.5 HP motor with variable speed via a VFD with feed speeds from 9.8 to 52.4 FPM.Equipped with & Features -- Inside you will find interior LED lighting while all the controls on this Opera are upfront via a touch screen -- Constant pass lineNOTE : This calibrating sander has a total of 1,982 power on hours and ONLY 89 run (conveyor) hours. This is a very loaded, LOW Viet Viet Opera 5 (4) Head 53″ Calibrating Sander

BIESSE-VIET OPERA 5-3.3 Denibbing Sander with 53" Width Capacity:53" Width cap. Denibbing Sander with a patented combination of rollers and rotating/oscillating discs make the VIET Opera Sanding Machine the ideal finishing solution for entry doors, cabinet doors, drawer fronts, sheet goods, shutters, face frames, furniture, and much more. Ideal solution for all sanding applications including whitewood, stain, and sealer coats. Sanding Drums - Made of steel, mounted on eccentric Shaft, to adjust the sanding belt thickness - Drum rubber with helicoidally grooves, balanced and rectified - Dust collection hoods with special design for best performance - Pneumatic ON/OFF of unit from panel control - Sanding belt tension rollers made of steel, balanced and rectified - Front pressure rubberized roller (1 roller) - Back pressure rubberized roller (1 roller)Head Configuration: -- 1st Unit: (15) Rotating discs with Slide-out system for easy setup. 11 kW (15 HP) Electronic Inverter with inverter speed control. -- 2nd & 3rd Units: 300 mm dia. Teflon hub for 36 strips. Oscillating System with electronic 4 kW (5.5 HP) inverter speed controlled. Specifications: -- Working Width: 1,350 mm (53.15"). -- Constant Pass Line TM (Fixed Table). -- Working Height Opening: 200 mm (7.87"). -- Laser Electronic Positioning for working thickness. -- Min. processing thickness 3 mm, Max. processing thickness 200 mm. -- (2) Longitudinal rotating brush-backed sanding rollers. -- 5" Rotating sanding discs. -- Forward speed 3-16 m/Min. -- Vacuum Table with 7.5 kW (10 HP) Motor, Electronic System, IPC Control. -- 60-Shore Rubber Conveyor belt with ground laminair surface. Pneumatic belt tracking -- Front & Rear Extension tables with rollers. -- Emergency stop.Equipped with: -- IPC Touch-screen control: Simple & user-friendly "TOUCH SCREEN" IPC control with a color monitor. This control system supports the management of all machine parameters. -- PC processor provides control and feedback information to the machine in real-time. -- The software version can be configured for right and left-handed operation. -- Text-free user interface; icons facilitate the operator's task. -- Optional rotating blower attachment at the back to blow off dust particles as items come off the machine. Electric Cabinet: -- "Check panel" alarms with LED - Automatic Star/Delta starter for main motors - Pad-lockable main switch - Thermal relay protections on all motors - Amperometer for all main motors - Electronic digital readout with automatic thickness positioning - Motor protection IP 54Actual model is OPERA 5-3.3 XLL. Year on nameplate is 2020 but not connected until 2021. Weight is 4600 KG (10,200 Lbs).This machine works great and has been very lightly used in a small shop that found with the small volume of work this machine was Too High in capacity so better off hand sanding.

VIET (BIESSE) OPERA 5-3.3 XLL Denibbing Sander with 53" Width Capacity:53" Width cap. Denibbing Sander with a patented combination of rollers and rotating/oscillating discs make the VIET Opera Sanding Machine the ideal finishing solution for entry doors, cabinet doors, drawer fronts, sheet goods, shutters, face frames, furniture, and much more. Ideal solution for all sanding applications including whitewood, stain, and sealer coats. Head Configuration: -- 1st Unit: (11) Rotating discs with Slide out system for easy setup. 15 HP Electronic Inverter. -- 2nd & 3rd Units: 300 mm dia. Roller Brushes (Hub for 36 strips). Oscillating System with electronic 7.5 HP inverter. Specifications: -- Working Width: 1,350 mm (53.15"). -- Constant Pass Line TM (Fixed Table). -- Working Height Opening: 200 mm (7.87"). -- Laser Electronic Positioning for working thickness. -- Min. processing thickness 3 mm, Max. processing thickness 200 mm. -- (2) Longitudinal rotating brush-backed sanding rollers. -- 5" Rotating sanding discs. -- Forward speed 3-16 m/Min. -- Vacuum Table with 5.5 HP Motor, Electronic System, IPC Control. -- 50-Shore Rubber Conveyor. -- Front & Rear Extension Rollers. -- Emergency stop.Equipped with: -- IPC Touch-screen control: Simple & user-friendly "TOUCH SCREEN" IPC control with a color monitor. This control system supports the management of all machine parameters. -- PC processor provides control and feedback information to the machine in real time. -- The software version can be configured for right and left-handed operation. -- Text-free user interface; icons facilitate the operator's task. -- Optional rotating blower attachment at the back to blow off dust particles as items come off the machine. -- Includes matching transformer for 600 V to 460 V.

WEEKE BHP 200 FLAT TABLE MACHINE (W/ATC/BORING): -- Specifications:5' x 12' Bridge style gantry machine with User-Friendly "S/C Tech" "MATRIX" grooved phenolic vacuum table. -- Working Area:'X" Axis 145.6" (3,700 mm), "Y" axis 61" (1,550 mm), "Z" axis stroke is 12.8" (325 mm), max. material thickness of 4" (100 mm). -- Positioning Speed:"X" Axis is 164 FPM (50 MPM), "Y" axis is 131 FPM (40 MPM), "Z" axis 66 FPM (20 MPM);The head travels via AC brushless drives & THK linear motion guides on all axes. -- Worktable: User-Friendly "S/C Tech "MATRIX" grooved phenolic vacuum table for easy vacuum pod placement, divided into (2) work zones.(4) Front pneumatic pop-up positioning stops, (2) side pneumatic pop-up positioning stops & (4) back pneumatic pop-up positioning stops. -- Boring Unit:(1) 4 HP (3 kW) motor, variable speed for 1,500 - 7,500 RPM;(10) Independent vertical spindle with (5) in "X" axis & (5) in "Y" axis. -- Machining:(1) 12 HP (9 kW) High speed constant duty Router with HSK F63 adaptor,1,250 - 24,000 RPM, constant torque achieved at 9,000 RPM, RH or LH rotation(1) 8-Position tool changer magazine located at the back side of the spindle carriage.Router is powered by an 14 kW programmable frequency inverter. -- Machine & Operator Control:PC Front-End with WEEKE "PC 85T" + Windows "XP" + WoodWOP 5.0 operating system.17" TFT Color graphic monitor, keyboard for data entry, PC 85T hand control pendant; CD R/W & floppy drives, EtherNET interface for LAN connection to office PC, RS-232 serial interface, USB ports. -- Complete with:(1) 500 m³/Hr Vacuum pump, safety mats & safety fencing. -- Actual model is WEEKE BHP 200

WEEKE BHX 050 CNC MACHINING CENTER (VERTICAL): -- Specifications: Flexible "Vertical" Machining Center that uses less than 5 sq/m of valuable floor space, in addition to an innovative Panel Handling System. -- Working Cap.:Max. workable part size for "X" axis is 98.4" (2,500 mm); "Y" axis 33.4" (850 mm); max. part thickness 2.4" (60 mm).Min. worktable part size for "X" axis is 7.8" (200 mm); "Y" axis 2.7" (70 mm); min. part thickness of 0.47" (12 mm). - Automatic infeed & outfeed from the LH or RH side. -- Positioning Speed:The "BHX 050" can reach movement speeds of 164 FPM (50 MPM) in "X" & "Y" axes & 50 FPM (15 MPM) in "Z" axis with total safety, providing an unmatched working capacity. -- Boring Unit:(1) 3 HP (2.3 kW), Variable speed from 1,500 - 7,500 RPM motor, (8) independent vertical spindles with: (4) spindles in "X" axis & (4) spindles in "Y" axis.(3) Horizontal Spindles with (1+1) in "X axis & (1) spindle in "Y" axis.Boring block has QUICK-CHANGE spindle system. -- Operator & Machine Control:WEEKE "POWER CONTROL" + Windows + WoodWOP 6.0 + Operating System; "IntelCore 2 DUO" Processor.17" TFT Monitor; international keyboard, soft touch keypad & industrial mouse; RS-232 serial ports, USB ports; (1) 1.44 MB floppy disk drive, (1) CD RW drive, modem, Ethernet connection.Real-time multitask processing; programs can be transferred via diskette or downloading by wire is possible. -- Complete with:Pneumatic part clamping devices; sound enclosure and complete set of safety devices. -- Options Include:&#9679 (1) "X" Axis grooving saw; 9,000 RPM, saw blade dia. 100 mm. &#9679 (1) 7 HP (5 kW) Electro-spindle router with hydraulic "QUICK-CHANGE" tool system & "ETP 25" tool holders; variable speed from 6,000 - 18,000 RPM. -- Actual Model is WEEKE BHX 050.

WEEKE BHX 050 CNC MACHINING CENTER (VERTICAL): -- Specifications: Flexible "Vertical" Machining Center that uses less than 5 sq/m of valuable floor space, in addition to an innovative Panel Handling System. -- Working Cap.:Max. workable part size for "X" axis is 98.4" (2,500 mm); "Y" axis 33.4" (850 mm); max. part thickness 2.4" (60 mm).Min. worktable part size for "X" axis is 7.8" (200 mm); "Y" axis 2.7" (70 mm); min. part thickness of 0.47" (12 mm). - Automatic infeed & outfeed from the LH or RH side. -- Positioning Speed:The "BHX 050" can reach movement speeds of 164 FPM (50 MPM) in "X" & "Y" axes & 50 FPM (15 MPM) in "Z" axis with total safety, providing an unmatched working capacity. -- Boring Unit:(1) 3 HP (2.3 kW), Variable speed from 1,500 - 7,500 RPM motor, (6) independent spindles with: (4) spindles in "X" axis & (2) spindles in "Y" axis.Boring block has QUICK-CHANGE spindle system. -- Operator & Machine Control:WEEKE "POWER CONTROL" + Windows + WoodWOP 5.0 + Operating System; "IntelCore 2 DUO" Processor.17" TFT Monitor; international keyboard, soft touch keypad & industrial mouse; RS-232 serial ports, USB ports; (1) 1.44 MB floppy disk drive, (1) CD RW drive, modem, Ethernet connection.Real-time multitask processing; programs can be transferred via diskette or downloading by wire is possible. -- Complete with:Pneumatic part clamping devices; sound enclosure and complete set of safety devices. -- Options Include:&#9679 Max. workable part size for "X" axis is 120" (3,050 mm. &#9679 (1) "X" Axis grooving saw; 9,000 RPM, saw blade dia. 100 mm. &#9679 (1) 7 HP (5 kW) Electrospindle router with hydraulic "QUICK-CHANGE" tool system & "ETP 25" tool holders; variable speed from 6,000 - 18,000 RPM. -- Actual Model is WEEKE - BHX 050.