sawmill Equipment For Sale

NORDFAB NFK Series Modular Dust Collector with (8) Modules, reverse air cleaning and drag chain unloading into a Rotary Air Lock (RAL) --23,000 CFM approx. capacity based on filter area and desired Air to Clothe Ratio. With 50 HP. Consisting of (248) filter bags of 8.7" dia. x 77.2 " long(220 mm x 1,960 mm long) also (8) filter bags of 8.7" dia. x 54.1" long.(220 mm x 1,375 mm long) - located at cleaning fans - for a total of 3,680 sq. ft. of filter area. -- Consists (8) modules and (1) inlet blank module. Fan inlet approx 26" dia. -- Bottom conveyor chain with scrapers carrying the dust to one end and fed into the RAL -- Includes NRS-10 Rotary Air Lock and Transfer Blower to convey the dust to an enclosed waste container (not included). -- Electrical control panel with starters included. -- Overall dimensions 32' long x 7.5' depth x 13.5' high (without support steel)., Approx weight 10,000 lbs. --Actual model is NFK 8AJ/1BL

Nordfab Air Blower with 40HP Motor

Northern Automation Lumber Stacker with Lift Table. 3 phase. 36"-192" capacity. #C935

Northtech horizontal band resaw, (2) blades, will cut up to a 12 x 12" cant, powered by (2) 20 HP 460 Volt 3 Phase motors, runs (2) 1 1/4" band blades, Excellent Condition, (new condition with less than 4 hours use). Owner is retiring. Ref# 119, Contact Amy (928) 723-9449

Has (2) Blades Will cut up to a 12 x 12" Powered by (2) 20 HP 460 Volt 3 Phase motors Runs (2) 1 1/4" band blades Excellent Condition, (new condition with less than 4 hours use).

16 HP 12 filter bags up 4 collection bags lower Lots of pipe

Norwood LumberPro HD36 23hp (627cc) B&S V-Twin OHV electric start gas engine , 4 ft. bed extension for 16 ft. total , log rolling ramp, auto dog assist. Used as hobby mill - low hours. Includes any new blades available jack stands for levelling Stationary now but can easily converted to mobile.From Mgf.

Nova Dry Kiln 26’ wide x 25’ deep holds 5500-12000 board feet propane or Natural Gas fired

NOVA TTF-6200 Dry Kiln System; Unassembled Front Load Kiln Designed to hold 5,100 bd. ft 4/4 Lumber, or 6,120 bd. ft 8/4 Lumber, Using 3/8" (9 mm) stickers. -- Specifications: Interior Dimensions: H 10' 3,5" (3.14 m), D 7'2"(2.19 m), W 25' 3" (7.7 m). -- Loading Door Opening: H 9' 10" (2.85 m), W 25' 3" (7.7 m). 1/8 " Aluminum sidewall bumpers, side hinged doors, exterior installation. -- Average 4/4 capacity: 5,100 bd. ft (12 m3) with 3/8" (9 mm) stickers. -- Average 8/4 capacity: 6,120 bd. ft (14 m³) with 3/8" (9 mm) stickers. -- Price shown is for kiln only. -- High horsepower heat requirement: 128 k BTU/hour. -- Heated Floor System, manuals and blueprints. -- Electrical Requirements: 230 VAC, 1 Phase, 60 Cycle, 25 kw/Hr max.

(2) Unassembled front load Kilns only System with high HP heat and exhaust designed to hold 8,461 bd/ft (20 cub.m) of 3/4" (25 mm) lumber and 10,475 bd/ft (25 cub.m) of 8/4" (50 mm) lumber (35 cbm). -- Kilns internal dimension: Height 12'3-1/2" (3.75 m), Depth 16' (4.88 m), Width 21' (6.4 m). -- Loading door opening of 10' (3.05 m) x 21' (6.4 m); 1/8" aluminum side wall bumpers, side hinged doors, exterior installation. -- High HP will service the heat requirements up to 245k BTU/Hr. -- Electrical requirement of 230 VAC, 3-Phase, 60 Cy; 7.21 kW/Hr. -- System includes: Timber Dry management automated Dry Kiln Controls for each kiln, touch-screen operator interface, data recording, optional remote access, and networking capability, Replacement part kit for a kiln. Manuals & Blueprints

Unassembled Front Load Kiln with Standard Heat and Exhaust -- Interior dimensions: H 17' 6" (5.33 m), D 25' 8" (7.8 m), W 26' (7.9 m). -- Loading Door Opening: height 14'6" (4.4 m), width 25'3" (7.7 m). 1/8" Aluminum Bumper Walls, Top Hinge Door, Exterior Installation. -- Average 4/4 capacity: 25,459 Bd Ft. with 3/4" stickers. Average 8/4 capacity: 33,293 Bd Ft with 3/4" stickers. -- Price shown is for kiln only. -- Standard HP Heat requirement: 382k BTU suitable for drying dark hard woods; Optional high HP Heat requirement: 674k BTU suitable for drying softwood and white hardwoods. -- Electrical requirements: 480 VAC, 3 Ph., 60 Cy; 16.5 kW/Hr. Timber Management Control System with touch screen operator interface, data recording, remote access & networking capability. -- Features: Control room with heated air intake; 12'H x 4'D x 26'W. Top Hinge door opening System includes "230" electric chain hoist. Boiler Room: 12' W x 25' D x 17'6" H. 10' roll up & (1) access door. - Timber Dry Management Network Capability.

2023 Nyle L200M Kiln 220V Single Phase 4 Fans Very Good Condition Kiln Unit Dimensions (H x L x W) 37” x 32 1/2” x 20 1/2”

Nyle Firewood Dry kiln No chamber included

OGAM Gang Rip 30HP Motor w/electrical still Hooked Up, Model PO 195, S/N 15149

Oliver Sawmill New Carriage Wheels New battery

1990 Onon Cummins MDL 500DFFB 39955F S/N J900356550 3 Phase 500 KW Genset

ONEIDA AIR SYSTEMS XXK200300 Cyclone Dust Collector w/ Rotary Air Lock: Cyclone & Fabric Filtration Dust Collection System. -- 3,800 CFM @ 12" SP to 6,800 CFM @ 2.7" SP with 20 HP Baldor Class F, TEFC motor with 1.15 service factor. -- High efficiency 12-gauge cyclone barrel with fully seam-welded construction. Powder coated paint finish, weather-proof cyclone and fan blower. -- (4) High Efficient Axtar Spun-Bonded Media cartridge after-filters for 620 sq. ft. of filter media with inverted plenum. Filters 99.9% efficient of 0.2 - 2.0 microns, Teflon-like coating to facilitate dust cake release. -- Fan is welded carbon steel, backward incline, dynamic, two plane balanced. Same as aircraft turbine rotors. -- 16" Rectangular Inlet with square to round inlet adapter. -- Includes: Freestanding Leg Kit with Rotary Airlock, magnetic starter, internal silencer reduces sound to 82 dB @ 10'. MADE IN THE USA.

ONEIDA AIR SYSTEMS XXK070323 Cyclone Dust Collector w/ Rotary Air Lock: Cyclone & Fabric Filtration Dust Collection System.Specifications: -- 2,900 CFM @ 1.5" SP with 7.5 HP US Made, Class F, TEFC motor with 1.15 service factor. -- High efficiency 12-gauge cyclone barrel with fully seam-welded construction. Powder coated paint finish, weather-proof cyclone and fan blower. -- (2) High Efficient Izumi Axtar Spunbond Media cartridge after-filters for 310 sq. ft. of filter media. Filters 99.9% efficient of 0.2 - 2.0 microns, Teflon-like coating to facilitate dust cake release. -- Impeller is 16.5" Diameter, Single-piece, backward inclined, non-sparking/non-ferrous, cast aluminum alloy. -- Inlet size 10" round. outlet 12" round dia. Includes: -- Rotary Air Lock, magnetic starterOptions: -- Freestanding Leg Kit with Dual 55-Gallon steel drum less Rotary Air Lock...as for pricing. MADE IN THE USA.(Actual P/N XXK070323-460-AIR).

ONEIDA AIR SYSTEMS FXK041500 Cyclone Dust Collector w/ After-Filter Plenum: Cyclone & Fabric Filtration Dust Collection System. -- 3,800 CFM @ 12" SP to 6,000 CFM @ 2.7" SP with 15 HP Baldor Class F, TEFC motor with 1.15 service factor. -- High efficiency 12-gauge cyclone barrel with fully seam-welded construction. Powder coated paint finish, weather-proof cyclone and fan blower. -- (4) High Efficient Izumi Axtar Spunbond Media cartridge after-filters (hanging) for 620 sq. ft. of filter media. Filters 99.9% efficient of 0.2 - 2.0 microns, Teflon-like coating to facilitate dust cake release. -- Fan is welded carbon steel, backward incline, dynamic, two plane balanced. Same as aircraft turbine rotors. -- Inlet size 14" round. outlet 16" round dia. -- Includes: Heavy Duty angle iron stand, magnetic starter, internal silencer reduces sound to 85-87 dB @ 10'Includes Rotary Air-lock for dumping into a waste bin!MADE IN THE USA.

ONEIDA AIR SYSTEMS XXK10 Cyclone Dust Collector w/ Rotary Air Lock: Cyclone & Fabric Filtration Dust Collection System.Specifications: -- 3,800 CFM @ 2.3" SP with 10 HP US Made, Class F, TEFC motor with 1.15 service factor. -- High efficiency 12-gauge cyclone barrel with fully seam-welded construction. Powder coated paint finish, weather-proof cyclone and fan blower. -- (3) High Efficient Izumi Axtar Spunbond Media cartridge after-filters for 465 sq. ft. of filter media. Filters 99.9% efficient of 0.2 - 2.0 microns, teflon-like coating to facilitate dust cake release. -- Impeller is 17" Diameter, Single-piece, backward inclined, non-sparking/non-ferrous, cast aluminum alloy. -- Inlet size 12" round. outlet 12.5" x 10" square dia. -- Includes: Heavy Duty angle iron stand, magnetic starter, and Rotary Air Lock. MADE IN THE USA..