Equipment For Sale

BOERE - TKS 900, ...2-Head Top Wide Belt Sanding Machine900 mm (36") Working width; equipped with: (1) Contact roller, (1) Fine sanding pad. Head Configuration -- 1st Head: Rubber contact roller, spirally grooved, Shore hardness 80, diameter 265 mm (10.4"), driven by 18 kW (25 HP) motor. -- 2nd Head: Sanding pad, electronic-pneumatic controlled, 114.7 kW (20 HP); Air blowing unit for cleaning the abrasive belt. -- All heads use abrasive belts size: 910 x 1,900 mm (35.8" x 74.8").Feed System -- Variable feed speed: From 5 - 25 MPM (16 - 82 FPM); 1.5 kW (2 HP) motor. -- Motorized part thickness opening: 3 - 150 mm (0.1" - 6"), driven by 0.12 kW (0,15 HP) motor.Complete with: -- Emergency Stop Systems for abrasive belt breakage and low belt tension. -- Infeed safety bar for operator protection and oversized parts. -- Automatic Star Delta starters, motor load meters. -- Pneumatic belt tension. -- Emergency Stops at the front & back. -- Extended infeed belt, approx. 42" long.Actual model: BOERE "TKS 900".

Boge compressors S-100 100HP S/N 50475

Model: C 30 N PSI150 3.210 m3/min CFM: 113 30 HP Size: 30.4 x 41.6 x 68.3 Weight: 1193 lbs

BOILERSMITH 400 HP BOILER, WOOD-FIRED -- Wood-Fired BOILERSMITH Boiler fitted with CHALLENGER Combustion Unit. -- Complete with the following major components and features: -- 250 PSIG design pressure. -- BOILERSMITH Boiler Model HRT2H8-2600SF-XW-250 with 2600 Sq. Ft. boiler surface area. -- Fuel can vary in moisture up to 50%. (Boiler HP is reduced as moisture increases.) -- Fuel feed Auger with Variable Frequency Drive. -- Fire-Tube Boiler with integrated Air Blast Tube Cleaning. -- De-Ash Augers. -- All Electrical Controls and starters. -- All mechanical/electrical engineer's drawings.NOTES: Removed and ready to load onto two trucks, 38,000 and 42,000 pounds. 15,000 to 16,000 pounds per hour steam if burning wood pellets. No building included but same building can be purchased from STAR.

Biomass Boilersmith Boiler 400hp 250 psi. barely used, 90 percent life expectancy All inclusive,boiler, Biomass unit, ash conveyors, all input/ feed conveyors, EPA approved pollution mitigation system, Electrical components. Was designed to have a Co-Gen unit added

BolDesign Kiln that includes Future-Design Controls FDC-2010-K5C Small Kiln Features • Board Feet Capacity: 2,000 to 10,000 BF (Board Feet) • Expect a 6-9 Week Turn Around • Easy to Clean and Maintain • Built with Aluminum and Stainless Steel, The Same Aluminum that is food grade used in Commercial Kitchens • RH control results in less lumber damage, this leaves you with better, brighter colors These Kilns are Built for Forklifts • Pallet Stock Drying Kiln; Disassembled crated and ready to load. 1 truck

Mechanical Pyramid Section Bending Machine Model # Z302 R-PR Voltage # 220/3 50/60

Pre-milling Unit End Trim Profile/Flush trimming Unit Corner Rounding Unit Profile scraping Buffing Max feed speed: 10 m/min Maximum panel thickness: 50 mm

Brandt KDF 440C Edgebander

BRANDT AMBITION 1440 (KDF-440 C) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge & workpiece capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") panel thickness, 160 mm (6.30") min. panel length, 70 mm (2.76") min. panel width.Equipped with: -- Adjustable Infeed Fence: Manual adjustment. -- Joint Trimming/Pre-milling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, left-hand & right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. -- Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting; 0.4 - 8 mm (0.016" - 0.31") strip thickness; 3 mm (0.12") PVC max. coil thickness. -- Hot Melt Glue Application Unit: 6 - 10 kG/Hr (13 - 22 Lbs/Hr) Melting capacity (depending on glue type). -- Pressure Zone: (1) Driven & (2) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speeds: 8 - 14 MPM (27 - 45 FPM); 11 MPM (36 FPM) when contour trimming. -- BRANDT "POWERTOUCH" Control with: 21" HD LCD Touch Screen Monitor.Workstations: -- Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors with 0° - 15° automatic chamfer, pneumatic adjustment & activation/deactivation of edging material overhang using "POWERTOUCH" control. -- Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt with Horizontal & Vertical Tracing wheels, Brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover with (3) Positioning options: Profile 1, Profile 2 & Flush Trimming. -- Multifunctional Trimming Unit: (2) 0.4 kW (1/2 HP) - 12,000 RPM Motors for leading & trailing edges vertical corner rounding of panels, Servo motors for positioning of work unit & horizontal copy wheels. Either radius or chamfer cutters can be mounted, 3 mm (0.12") max. edge thickness. -- Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"); Servo control positioning of vertical & horizontal copy wheels; PVC scrape collection box, pneumatic adjustment using "POWERTOUCH" control, pneumatic disengagement. -- Top & Bottom Glue Scraping Unit: Flush on panel surface with floating insert knives. -- Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) - 2,750 RPM Motors.Complete with: -- Rubber padded feed chain w/top idle hold-down rollers; 1.5 kW (2 HP) feed motor; 32" diameter coil table; padded sound enclosure. -- Actual Model is BRANDT AMBITION 1440 (KDF 440 C).

BRANDT - KDN 630, ...Edgebander.0.4 - 8 mm (5/16") Edge cap., panel thickness 5/16" - 1-9/16", min. panel length 160 mm (6-3/8"), and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function.Equipped with: -- Quick heat up glue system, w/glue tank for maintenance, and glue color change. -- Automatic magazine for strip & coil (large coil table, 800 mm dia. to accommodate large coils of 3 mm PVC stock), 3 mm PVC guillotine, (1) drive plus (3) idle roll "pneumatically controlled" pressure sections. Signal infeed light to insure proper spacing between panels. -- Automatic height adjustment with top pressure beam for all workstations, equipped with digital height indicator.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motors), chamfers 0° - 15°. -- (2) Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motor) with insert knives for 3 mm PVC radius. -- Top & Bottom scraping for 2 - 6 mm radius, pneumatically controlled blow off nozzles; Top & Bottom buffing (0.25 HP - 1,400 RPM motors). -- End trim & flush trim stations with: HF Motors, electronic brakes; feed chain track speed of 46 FPM, 2 HP feed drive. Complete with: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, internal Modem for remote diagnostic link, and used tooling.

BRANDT - F-13, ...Top & Bottom TrimmerFor simultaneous top & bottom flush/radius trimming of the oversized edgeband on straight & shaped workpieces with inside-and-outside radii.Specifications: -- Top & Bottom edge trim PVC, HPL, and veneer edgings; up to 3 mm max. thickness. -- Manually operated; 1/2" - 2-1/4" panel thickness; 1-3/8" min. inside radius. -- Features: Independent top & bottom trim heads (0.5 HP - 11,800 RPM motor each). -- Built-in air jet blowoff device; 31" x 48" table size; dual foot pedal control.NOTE: Intermittent fault in the Control Panel, which will require replacement.

BRANDT - "KD-68", ...Edgebander1/4" (6 mm) Edge thickness cap. (will even do 8 mm max.); max. edgebanding height: 60 mm (2-3/8"); min. workpiece length: 160 mm; width: 70 mm (2-3/4").Equipped with: -- Quick Melt Glue System with: (10) Min heat up time and reversible glue roller. -- Automatic magazine for strip & coil stock; 3 mm PVC guillotine; 3-roller Pressure Section.Workstations: -- Double motor end trim on uni-slide: 0.33 HP - 14,400 RPM; chamfers 0° - 15°. -- Top & Bottom flush/bevel & radius trim; bevels 0° - 15°; 1/2 HP - 14,400 RPM motor ea.; w/SIKO digital readouts. -- Top & Bottom scraping for standard or 3 mm PVC edging; air jet blowoff; SIKO digital readouts. -- Top & Bottom buffing: 1/2 HP - 1,650 RPM; adjusts 0° - 40°. -- Feed chain feed speed: 36 FPM.Complete with: Electronic motor brakes on both trimmers; padded sound enclosure; eye level height swivel control panel w/fault sensor control; adjustable outboard panel support track; frequency converter; used tooling.

BRANDT - KDF-550 C, ...Edgebander with Premill & Corner RoundingEdge & workpiece capacity. Edge: 0.4 - 8 mm (0.016 - 0.31"); panel thickness: 8 -60 mm (0.31" - 2-3/8"); min. panel length: 60 mm (6.29"); min. panel width: 70 mm (2-3/4").Equipped with: -- Premilling Station with: Diamond cutterheads; (2) motors @ 2.25 kW (3.0 HP) - 12.000 RPM; LH & RH rotation w/pneumatic jump control for chip free & clean panel edges. -- Infeed fence with: Servo motor positioning. -- Automatic Edge Magazine. For strip & coil stock; strips: 0.4 mm - 8 mm (0.016" - 0.31"); coils up to 3 mm PVC and "HD" guillotine. -- Pressure Section. 1st Roller driven; plus (3) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speed: Variable; 8 - 14 MPM (26 - 46 FPM); 11 MPM (36 FPM) when using contour trimming. -- BRANDT "PowerControl PC 16"; memory: 256 MB RAM; 1 GB Flash Card Drive; Operator control panel with: 22" Color HD wide screen; soft keypad; internal modem for remote diagnostic link.Workstations -- End Trimming; (2) Motors @ 0.35 kW (1/2 HP) 12,000 RPM; automatic chamfer from the control panel: 0°- 15°. -- Flush/Bevel-Fine/Radius Trimming Unit: Top/bottom (2) motors; 0.55 kW (3/4 HP) 12,000 RPM; auto tilt positioning 0° - 25°; combination flush/radius/chamfer cutterheads; horizontal and vertical tracing wheels. -- Includes: (3) Positioning options: Profile 1, profile 2, and flush trimming. -- Corner Rounding Unit: (1) Motor; 0.35 kW (1/2 HP) - 12,000 RPM for leading & trailing edges; vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Scraping, Multi-Profile (PVC) Top/Bottom with (2) profiles: 1 mm & 2 mm or 3 mm Instead of 2 mm; Servo control positioning of vertical & horizontal copy wheels; PVC scrape collection box. -- Scraping Glue Unit: Flush top/bottom on the panel surface with floating insert knives. -- Buffing Unit: Top/bottom (2) motors; 0.10 kW (0.125 HP) - 2,800 RPM.Complete with: Motorized, programmable holddown pressure beam; padded sound enclosure. -- Actual Model: BRANDT, OPTIMATKDF 550 C

BRANDT KDF 780 2C EDGEBANDER WITH PRE-MILL AND CORNER ROUNDINGBasic Specifications: -- 0.4 - 15 mm (5/8") Edge cap., panel thickness 5/16" - 2-3/8", min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; line control (NO limit switches) for workstation function.Features: -- Pressure Beam with motorized height adjustment for all work stations includes digital height indicator. -- PC-20 Program Control; with 12" Industrial PC flat screen 256 MB RAM, 1 GB Flash Card, with USB Port & remote diagnostic link. -- Signal infeed light to ensure proper spacing between panels. -- Quick heat-up glue system,(approx. 10 minutes) w/hopper feeder & w/glue tank for maintenance & quick glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 minutes or more. -- The glue applicator roller is also reversable and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table 800 mm diameter to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (3) secondary rollers "pneumatically controlled" pressure section. -- Variable Feed speed 36 - 65 FPM (3 HP feed motor) -- Corner rounding station operates at 16 m/Min (52 FPM).Workstations: -- (2) Motor Pre-milling Unit; (2) 3 HP motors (12,000 RPM) to clean-up potential chipped edges. -- End Trimming: (2) 1/2 HP - 12,000 RPM motors) chamfers 0° - 15° via programmable controller. -- Pre-Trimming: Top & bottom flush/bevel trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Fine-Trimming: Top & bottom flush/bevel/radius trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Corner Rounding (Contour) Trimming Unit: (2) motor 1/2 HP - 12,000 RPM each motor for corner rounding for front & trailing corners on the fly. -- Profile Scraping Unit: Top & bottom for 1 - 3 mm PVC radius, depending on tooling. -- Open Space: For the ability to add a top & bottom flat/glue scraper. -- Buffing Station: Top & bottom oscillating buffing (0.25 HP - 2,800 motors). -- Hot Air Unit: (1) Hot air blower to reactivate top/bottom edge after profile scraping and buffing, restoring original edge color luster.Complete With: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts. -- End trim, flush trim & fine trim and corner rounding stations have HF motors with electronic brakes. -- Original Factory machine documentation.

--make offer--excellent condition-- BRANDT OPTIMAT KTD 820 Contour Edgebander Specifications: Designed for straight, curved (contour), or beveled edgebanding. Edgebanding thickness 0.4 - 3 mm (0.02” - 0.12”). Coil cutoff 0.4 - 3 mm (0.02” - 0.12”) (Max. edge height 45 mm/1.77”). Panel thickness 16 - 40 mm (0.63” - 1.57”). Min. radius 25 mm (0.98”). Min. panel length 180 mm (7.09”), Min. panel width 100 mm (3.94”). Feed speeds 0.7 - 4.2 MPM (2.30 - 13.80 FPM). Equipped with: 33” Dia. Vertical coil table. Small glue pot for quick heat-up. Magazine for coil or solid strips. Guillotine. Handheld gluing unit, with Tool balancer & Rotating jib with 8’ Travel. (2) 23-1/2” x 27-1/2” x 35 H Work tables. Large panels can be glued by guiding handheld gluing unit around panel mounted to vacuum suction table. Small panels can be glued by guiding panel along gluing unit mounted to table. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

2007 Brandt KDF 680 Single sided Edgebander with Pre Milling and Corner Rounding

Brandt KDN 770 2C Machine has been removed from service. Owner claims it is ready to run! Specs (to be confirmed): Hot Melt granulate quick heat-up glue system, overhead glue tank for easy maintenance & glue color change. Automatic magazine for strip & coil (large 800 mm dia. coil table to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine. (1) Drive plus (3) idle rolls "pneumatically controlled" pressure sections. End Trimming: 0.33 HP - 12,000 RPM Motors, chamfers 0° - 15°. Flush Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index pre-sets, (2) 0.5 HP - 12,000 RPM motors, cutter heads with insert knives. Fine/Radius Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index presets (0.5 HP - 12,000 RPM motors), cutter heads with insert knives for 3 mm PVC radius. 2 motor corner rounding Scraping Unit: Top & bottom for 2 - 6 mm radius, pneumatically controlled blowoff nozzles. Buffing Unit: Top & bottom buffing (0.25 HP - 1,400 RPM motors). Variable feed chain track speed from 8 - 20 MPM (26 - 65 FPM), 2 HP feed drive.

Great Condition Recently Fully Serviced Profile Scrapers and Surface Scrapers No Premill/No Buffers

Brandt Ambition 1110 Edgebander