Equipment For Sale

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i5z NORTHTECH NT-EV-920RC DUAL HEAD WIDE BELT SANDER 2-Head wide belt sanding machine with 37" capacity. - Heads: 1st head: 8-1/4" Dia. grooved rubber contact roll, with 20 HP motor. 2nd head: Combination finishing platen with grooved rubber roller and polishing pad, with 15 HP motor. Two (2) infeed and outfeed spring loaded hold-down rollers; 2 HP variable speed feed drive. Sanding belt size: 37" X 85" and with electronic belt tracking. Motorized opening between the conveyor and sanding bed. Ammeters for measuring motor loads.

2007 Northtech NT-CS14R-53 3 phase 460 volts 5 horsepower SN 07113 Operates good

NORTHTECH NT-6108ES-6 Edge SanderSpecifications: Sanding Belt is powered by a 3 HP 230/460V motor. -- The platen measures 6-3/4″ X 39″ and has NEW graphite. Rubber covered direct drive pulley. -- Equipped with: (1) 7-3/4" x 37" Adjustable side table and (1) 11-1/2" x 19" Adjustable end table; both side & end tables have vertical table travel w/hand wheel adjustment. Complete with: -- Magnetic controls with overload protection & dust hood with 4" dia. outlet.

Rigid one piece welded steel frame, with 10 HP direct drive spindle motor at 7,800 RPM, 1-1/4" x 4-1/2" stackable multi-cutter spindle to mill stile, rail & raised panel profiles. -- Stackable cutter spindle with push button indexing to significantly reduce set-up time as each station is preset; the change from one cutter to another is achieved via a select switch for each operation. -- Complete with: X - Y Sliding table w/pneumatic holddown. -- 2-way linear movement for straight or arch top doors up to 50" long. -- 5" Dust collection hood, and cutter shield. -- Includes: (1) Cathedral arch templates, (1) complete set of tools.

Northtech MRS-12N Gang Rip 50 HP Motor Needs a new safety with on the door

Northtech NT 16R-10 Tilting Arbor Table Saw Infeed Roller 10 HP Motor

Northtech Chop Saw

NORTHTECH NT-610EL Top & Bottom Planer:24" Wide x 7.5" thick capacity; 1/4" minimum thickness; 12" minimum stock length.Specifications: -- Cutterheads: 25 HP top head; 20 HP bottom head; 5,800 RPM on cutterheads; (6) row spiral insert cutterheads, Carbide knives 15 mm x 15 mm x 2.5 mm 4-sided -- Feed works: 3 HP variable speed feed with speeds from 20 to 75 FPM; 1 HP motorized raise and lower of bed; DP-525 digital thickness controller; Overhead carpet style feed system Equipped with & Features -- Sectional chip breaker; Hard chrome plated bed; Automatic lubrication for feed system; Amp load meter -- Dust Requirements: 3,800 CFM; (1)10" and (1) 7" dust outlet Seller states this machine has less than 600 Hours of use.

Northtech horizontal band resaw, (2) blades, will cut up to a 12 x 12" cant, powered by (2) 20 HP 460 Volt 3 Phase motors, runs (2) 1 1/4" band blades, Excellent Condition, (new condition with less than 4 hours use). Owner is retiring. Ref# 119, Contact Amy (928) 723-9449

Northtech FR-200 Frame SawSpecifications: -- Saw capacity of 6" width x 8" vertical capacity. -- Minimum working 2"; high X 12"; long. -- Main drive motor to saw frame is 30HP 3PH, wired 460 --V servo drive system to feed works is 1/4HP 3PH, --Blower to saw frame rack for added cleaning value is 3HP 3PH, -- Body of frame saw is (2) sections allowing for fast access to the saw frame, -- Saw blade speed is fixed at 550RPM, -- Dust extraction requires min 3000 CFM and is arranged with (4) 5" ports, -- Blade size is standard with 500mm L x 40mm W x 0.9mm body in stellite or TCT tip,Equipped with & Features -- Digital electronic oiling system provides proper lubrication to the saw frame guides -- Vertical rail system which allows optimum cooling and long term durability, -- (4) guide blocks are thermo- censored to allow auto shut-off of machine should possible heat buildup occur.Machine dimensions 122"; L X 40"; WX, 79"; H weight 7100 lbs. Machine was new in 2007.

NORTHTECH - NT-SL2000XL, ...Straight Line Rip SawSpecifications: -- 20 HP Direct Drive Straight Line Rip Saw. -- 2" Arbor. -- Distance from column to blade: 18 in. -- Saw blade size: 10" - 14". -- 3-1/8" Cutting capacity. -- Glue Line Saw. -- Feed Motor: 1.5 HP. -- Feed Speed: 20 - 105 FPM.

NORTHTECH NT 1000-50HCVS Single-Sided 40" PlanerSpecifications: -- 40" Planer, 40 HP main motor, Helical Head, Adjustable bed rollers 15 mm x 15 mm x 2.5 mm Carbide Insert cutters. -- The spiral cutterhead provides a high chip removal rate, superior surface finish and low noise. -- Powerful 40 HP cutterhead motor makes this planer ideal for heavy-duty planing and meets high production requirements. -- Variable feed speed is mechanical variable from 0 - 90 FPM. -- Power elevation of the feed bed with "727 M Digital Table Adjustment" for fast accurate, and convenient thickness setting. -- Extra heavy rib reinforced cast iron table, surface precision ground. Equipped with: -- (4) Powered steel bed rollers. -- (4) Upper rollers. -- (2) Powered corrugated infeed rollers. -- (2) Powered urethane outfeed rollers. -- Upper and lower limit switches for opening control. -- (4) Dual 50 mm jack screws for raise/lower bed movement; 12" max opening. -- 2 HP Elevation motor with manual adjust. -- Rear E-Stop for added safety. -- Dual 6" dust ports requiring 1,000 CFM @ points of extraction.

Manufacturer’s Specification - 15HP Motor + 1HP feed motor (with Wye Delta soft start) - Mechanical variable speed (45' – 100' FPM) provides a speed range for all material types and thickness ranges of 3/16”- 3-1/2”. - Bottom & top kickback fingers - Rack and pinion fence for precise and quick positioning. - Digital electronic oiler provides maximum chain and race life. - 15-1/2? distance from column to blade. - 8' glue line tolerance.

NORTHTECH Four (4) Head Lineal Brush SanderSpecifications: • Sanding Head configuration: 2 Top + 1 Opposing Right + 1 Opposing Left• Working width up to 12"• Working thickness range: 1/4" - 6"• Minimum working length: 30"• (2) Top 1.5 HP Sanding heads RPM are inverter controlled• (2) 1 HP Opposing side sanding heads RPM are inverter-controlled• 150/180 Grit setup included; other grits available upon request• (2) 1/4 HP feed motors with 25 - 105 feed speed range• (2) 5" top dust ports requiring 681 CFM @ point of extraction• (2) 4" Side dust ports requiring 436 CFM @ point of extraction• 230V or 460V 3PH 60HZ• Net / Gross weight: Approx. 1,056 Lbs / Approx. 1,300 Lbs• Approximate Machine dimensions (LxWxH): 59" x 52" x 67"• Tool box and Operation/Parts Manual included• Warranty is one-year parts

NORTHTECH NT-610 HC TOP AND BOTTOM PLANER: --24" x 8" cap., min. material length 12". Table size is 111" x 24". -- 50 HP top and 40 HP bottom belt driven motors; --Minimum working length is 12" and minimum working thickness is 1/4". -- Variable feed speed 55 - 155 FPM powered by a 5 HP feed motor; 1 HP motor for table raise & lower and (4) ball screws. -- Both cutter heads are helical carbide insert knife heads, 6,000 RPM. MACHINE FEATURES: -- Rugged cast iron and plate steel fabrication. -- Overhead feed cnveyor with 1,100 individual spring loaded "feed fingers" to provide excellent feed characteristics. -- Computerized top cutterhead positioner is accurate to +/-0.001" -- Cutterhead tooling technology gurantees low noise, reduced power requirements, minimal operations cost and repetitive finish on the most difficutl hardwoods. -- Patented lifting column system (synchronized transmission) gurantees repetitive setup and long-term dependability. -- DP-525 Thickness Setting Unit --Patented universal drive transmission for feed groups and infeed carpet allows a maintenance free design verses chain drives. -- Cutterheads are solid steel construction, dynamically balanced and mated with precision pulleys. -- Cutterheads are supported by "NSK" class 7 precision ball bearings and prcision housings. -- Chromed beds, Guards and skirts for operator safety. -- Additional Specs: Machine dimensions: L2830 x W185 x H1700 MM; Weight: 9,000 lbs; Dust Collection: 3600 CFM

NORTHTECH NT-610HC TOP AND BOTTOM PLANER: --24" x 8" cap., min. material length 12". Table size is 111" x 24". -- 50 HP top and 40 HP bottom belt driven motors; --Minimum working length is 12" and minimum working thickness is 1/4". -- Variable feed speed 55 - 155 FPM powered by a 5 HP feed motor; 1 HP motor for table raise & lower and (4) ball screws. -- Both cutter heads are helical carbide insert knife heads, 6,000 RPM. MACHINE FEATURES: -- Rugged cast iron and plate steel fabrication. -- Overhead feed conveyor with 1,100 individual spring loaded "feed fingers" to provide excellent feed characteristics. -- Computerized top cutterhead positioner is accurate to +/-0.001" -- Cutterhead tooling technology gurantees low noise, reduced power requirements, minimal operations cost and repetitive finish on the most difficult hardwoods. -- Patented lifting column system (synchronized transmission) gurantees repetitive setup and long-term dependability. -- DP-525 Thickness Setting Unit --Patented universal drive transmission for feed groups and infeed carpet allows a maintenance free design verses chain drives. -- Cutterheads are solid steel construction, dynamically balanced and mated with precision pulleys. -- Cutterheads are supported by "NSK" class 7 precision ball bearings and precision housings. -- Chromed beds, Guards and skirts for operator safety. -- Additional Specs: Machine dimensions: L2830 x W185 x H1700 MM; Weight: 9,000 lbs; Dust Collection: 3600 CFM

NORTHTECH NT 25 RS-HA Finger JointerFinger jointer with (2) shapers and a press capacity of 6" wide X 20' long pressSpecifications: -- Northtech Finger Jointer System w/ Model NT-25LS-HA Left Shaper, NT-25 RS-HA Right Shaper, Glue System, and NT-20AH-HA Pressing Station -- Left Hand Shaper Unit includes 20 HP Shaper, 7.5 HP Saw Motor, 1 HP Bottom Scoring Motor, and a Pusher Cylinder to Send Parts Away -- Right Hand Shaper Includes 20 HP Shaper, 7.5 HP Saw Motor, and Top & Bottom Scoring Motors and Glue Application Head -- Shapers have 29" x 28" Tables -- 50 mm Diameter Shaper Spindles -- Maximum Length X Height of Workpiece 40" x 6" -- Minimum Length X Height of Workpiece 6" X 0.8"Model NT-20-AH-HA Finger Joint Press -- Pressing Length: 20' -- Cut-Off Saw to Cut Pieces to Length. Saw Motor: 3 HP -- Hydraulic Press Feed with 7.5HP Motor -- Pneumatic Top & End Pressure -- All Units Include Push-Button ControlsNote: Purchase used in 2022 after being cleaned and checked, now replaced with a larger system

Has (2) Blades Will cut up to a 12 x 12" Powered by (2) 20 HP 460 Volt 3 Phase motors Runs (2) 1 1/4" band blades Excellent Condition, (new condition with less than 4 hours use).

Northtech NT SLR-16SC Precision 16″ Straight Line Rip Saw FEED SYSTEM --Saw motor: 15HP, 3PH 230/460V -- Feed: 1.5HP variable from 40′ – 120′ FPMPRODUCT DIMENSIONS -- Min. thickness: 3/16″ -- Max depth of cut: 4-1/16″ with 16"; Blade -- Max depth of cut: 3-1/16"; with 14"; BladeSpecifications: -- Direct Drive = Direct Drive -- Feed Hp. = 1.5 Hp. -- Feed System = 4"; Split Chain with True Trac -- Feed Speed = 40-120 FPM -- Assisted Start = Wye Delt"; -- Throat Capacity = 18-1/4"; -- Min. Length = 12"; 2nd Roller to Kickback -- Min. Thickness = 3/16″ -- Max. Thickness = 4-1/16"; W/ 16"; BladeGlue Line Rip = Guaranteed 12′ 4/4 stock @ 50 FPMEquipped with & Features -- Blade Size = 14"; Tungsten Carbide Tipped -- Dust Collection = 1417 Total CFM -- Dust Port Out = 4"; Top 6"; Bottom -- Arbor Diameter = 2″ Arbor -- Idle Rollers = (8) Idle Rollers -- Hold Down Style = 8 Spring Loaded Hold Downs -- Kickback Finger = (59) Lower (32) Top -- Automatic Mechanical Oiler -- Low Oil Warning = Low Oil Shut-off -- Laser = 100mw Laser Light & Mount Bracket

NORTHTECH - NT-920C-200: 2-Head Planer Sander Specifications -- 2-Head. 37" width cap.; 1-knife planer head followed by a wide belt sander head. -- 0" - 6" Motorized opening with: PLC control; keypad entry; LED readout for part thickness. -- 1st Head. 6" Dia. helical planer head with: (6) Rows of staggered carbide inserts; each insert has (4) usable sides; 30 HP motor. -- 2nd Head. Combination sanding head with: 4-5/8" Dia. rubber covered contact roll; 2-1/2" wide finishing platen; 20 HP motor. -- 37" x 75" Abrasive sanding belt; solid-state belt tracking. -- 3 HP Variable feed drive from 15 - 50 FPM; endless belt conveyor with automatic tracking.Complete with: -- Infeed over thickness bar. -- Emergency stops at infeed & outfeed. -- Air-operated disc brakes on sanding heads. -- Electrical interlocks on main access doors. -- Electrical controls with overload protection. -- Motor load meters. -- Panel cleaning brush.