Equipment For Sale

This Drum chipper is used in production of wood chips from logs and wood residues (slabs, board off cuts, veneer waste). It has a toothed driven roller system that allows an efficient infeed of the material, rotor with interchangeable thread locks and with a disposable steel plate in the front of the rotor, hydraulic nose-bar/anvil extractor, infeed conveyor with rubberized belt and hydro-pneumatic unit to lift the chipper/rotor lid. (maintenance). It comes with 01 set of blades and 01 nose-bar/anvil. Does not come with outlet conveyor. - Inlet width: 1000 mm; - Nominal chip size: 23 - 30 mm; - Inlet Height: 450 mm; - Main Motor indicated: 300 hp 4P (2x); - Rotor diameter: Ø 1000 mm; - Soft starter drive panel; - Shaft diameter: Ø 220mm; - Metal detector; - Toothed roller: 03 upper and 03 lower; - Estimated production: 130 m3/ h; (may vary according to the type of wood and the sharpening period of the knives); - Roller diameter: Ø 353mm; - Diameter of roller shafts: Ø 100mm; - Chipper Screen: 65 x 65mm; - Grooved roller: 01; - Infeed conveyor length: 5000mm (included); • Driven roller gearmotor: (helical gears); - Width: 3 500 mm; - Driven rollers motor: 15 hp (2x); - Height: 2 100 mm; - Main motor belt: Torque-Team; - Total length: 10 500 mm; - Inlet conveyor speed: 40 mL / min; - Approximate weight: 22 700 kg; - Number of rotor blades: 03;

SFVG1200 twin vertical Band Saw 1200mm wheel blade size. Machine used for the log break down process in continuous flow sawmill layouts. Capacity to process logs up to 500mm in diameter and 3.000mm long. This machine is fitted with main motor, motor drive panel, servo motor thickness selection, adjustable saw guides, slabs pneumatic side pressers, special chain and hydropneumatic tensioning system to tension the Band saw. - Wheel blade width: 6”; - Minimum log Length: 1200mm; - Standard maximum log length: 3000mm - Minimum diameter: 120mm; - Maximum log diameter: 500mm; - Saw cut width: 70 to 300mm; - 4 set of pneumatic side pressing rollers for side boards; - Motor size: 2 x 75CV 4P 50hz (INCLUDED) - Drive Panel Included; - Central chain motor size: 7,5 HP 4P; - Linear Cutting speed: 30m/s; - Feed speed capacity: 48m/min; - Saw Blades are not included. - Infeed conveyor length: 4.000 mm included; - Outfeed conveyor length: 6.000 mm included; - Machine width: 5.000 mm; - Machine overall Length: 12.000mm - Servo motor thickness setting system (INCLUDED); - Approximate weight: 15.000 kg;

Multirip circular saw for block cutting, with reinforced structure and high production speed. Trailed top and bottom rollers, upper rollers with adjustment, shafts with cartridge system for quicker and more efficient replacement of the set of saws, U-beam base with levelers and central lubrication. It does not come with the circular saws. - Maximum inlet width: 600 mm; - Minimum inlet height: 70 mm; - Maximum inlet height: 160 mm; - Double arbor: Ø 80 mm; - Number of saws per axle: 10x; - Exterior saws Ø: 350 mm interior saws - Ø: 110 mm; - Upper press rollers: 2x; - Bottom rollers: 6x; - Max. Feed speed: 35 m L / min for logs - 160mm above in diameter; - Max. Feed speed: 40-50 m L / min - only for logs 130-160mm in diameter; - Lower main motor indicated: 200 hp 2p (1x) Included; - Top main motor indicated: 150 hp - Main motor belt: 4 / 3v (8 Pcs); - Motor traction of the rollers: 5 cv 4p; - Gearmotor: GS (crown and pinion); - Length: 3366 mm; - Width: 2782 mm; - Height: 2233 mm; - Approximate weight: 5.470 kg

This is a Horizontal Band Saw Resaw Machine with Two saw heads. This is an ideal Machine for the recovery line, as it processes the slabs coming out of the Vertical Twin band saw machine “the resaw process”. It comes with an input chain conveyor, driven press rollers. Cutting Height and saw blade tensioning setting system. It also comes with main motor, motor drive panel, the Frequency inverter, gear motor drive panel. It does not include the saw blade. - Wheel blade: Ø1000mm; - Wheel blade width: 5"; - Maximum wood width: 400 mm; - Maximum wood height: 380 mm; - Minimum length of wood: 1250 mm; - Single Input table/ conveyor width: 600 mm; - Motor press roller: 1 cv 4P (2x); - With two independent infeed rollers; - Forward speed: 45-50m / min for small logs; - Main motor indicated: 2 x 60 hp - Soft starter Drive panel: included; - Servo motor thickness setting system (INCLUDED); - Main transmission belt: 3 x Channel B; Length: 6.532mm; - Width: 2.220mm; - Weight: 7655kg.

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i5h VANTEDGE MM 6.5 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): + EVA & Polyolefin Adhesive ready. Specifications: Working Capacity: Edgebanding thickness 0.4 - 3 mm coil stock capacity & 10 mm strip capacity. Min. panel width 85 mm (3.3"); min. panel length 125 mm (4.9"); panel thickness 10 - 60 mm (0.39" - 2.36"). Tape and Panel Infeed System: 750 mm Coil support table; adjustable track feed speed 14, 16 & 20 MPM (66 FPM). Heavy-Duty large solid polished steel panel infeed fence guide system. Large industrial digital adjustment for the Premill panel material removal amount. Top Pressure Beam Adjustment: Automatic adjustment from the PLC control; pneumatic Pop-Up Stop system. Red LED panel feed indicator light for correct panel spacing. Equipped with: Dual 3 HP Pre-milling motors w/diamond cutter heads; pneumatic "JUMP In/Out function. Misting unit prior to Pre-milling; large dual dust housing ports to help clean the Pre-milling system. Quick change Glue Reservoir for EVA & PO glues; Pressure Section/Infrared Heat Lamp System. Heavy-Duty automatic shear type Guillotine with: "Auto-Set" automatic intervention for strip & coil materials. (4) Pneumatic polished Pressure Rollers with manual digital adjustment to edge thickness. (1) Rubber infeed Tape Roller, (1) metal infeed Tape Roller; direct Universal Drive system - NO Chains. Teflon-coated glue pot; digital thermostats with automatic kick down when the machine is in idle mode. Workstations: End Trimming Unit: Dual 0.5 kW (0.67 HP) high frequency End Trim motors on precision "Auto Lube" Linear Guideways; 90° to 10° pneumatic tilt cut adjustment. Electronic sensors to safely monitor motor positions; thumb screw pneumatic adjustments for simplicity. Tilting Super Finish Top & Bottom Trimming Station: Dual High Frequency 0.65 kW (0.75 HP) motors with Combi Finish insert tooling.Top Servo driven positioning of motors for different edge trimming profiles & positions. Corner Rounding Unit: Motors on precision billet aluminum swing tracer arms with pneumatic guidance and Face Copy System. (2) Independent motors can be adjusted to match tape thickness via digital scales. Profile Scraping Unit: Top, bottom & side Copy Wheels to properly follow your panels edge. Panel Nesting System: Triple Copy System for panels with blind dados & hinge cup holes. Digital adjustment for fine-tuning the unit to the proper tape thickness. Flat Scraping Unit: Large copy wheels. Buffing Unit: Top & bottom Buffing Unit; 0.5 HP (0.37 kW) - 2,800 RPM motors; units tilt 0° - 30°. Dual Hot Air Blowers: To re-embellish edge materials. Operator Interface 10" Color touchscreen PLC with swivel Control Panel. The PLC controls all working units & the adhesive thermostats with 1-touch icon programmable selections. Photo indicator alarms to easily troubleshoot errors/issues. Complete with: I

Brand new never used!! 16’8” long 22” wide 19” height (adjustable)

MLS Number 11342021 2008 Vecoplan RG32/20U Grinder/Shredder Single shaft grinder / shredder 80 DBA noise level 32 in. by 42 inch opening waste grinder with vertical 2 cubic yard hopper 20 HP rotor motor Equipped with10 inch rotor with 20 indexable/replaceable cutter knives Rotor / cutter head grinds at 95 R.P.M. Hydraulic pusher ram with 1.5 HP two speed pump motor Separate electrical panel with push button controls 80 DBA noise level 8 inch exhaust 8 inch hump magnet screen to produce ½ in.in size Handles 1,000 to 1,200 lbs./ hour depending on product mix and loading. Machine still operating. Will be available sometime in May/June 2022

2016 Vecoplan RG52-60 U Stretch Slow Speed Grinder 60HP Electric Main S/N 112901

Vecoplan RG52-60 U Stretch Slow Speed Grinder 60 HP Motor No Control Panel

VECOPLAN RG 42-40 SINGLE SHAFT SHREDDERSpecifications; -- 40 HP MotorVecoplan ShredderModel: RG 42/40 XL PVYear: 2007Motor: 40 HP, 460V, 60HZRPM: 1465Feed Opening: 42" x 48"Blades on rotor: 27Weight: 3,700 lbs

Vecoplan RG 42/60 XL 60 HP Motor 15" Rotor 42" x 52" Hopper Opening 1" Screen This machine went through a rebuild. It was not big enough for the buyers application. Available immediately.

VECOPLAN RG52/60 SINGLE SHAFT SHREDDER Includes Box Dumper and ConveyorsSpecifications: --In Feed Opening: 52″ x 58″ --Rotor Length: 52″ --Rotor Diameter: 15″ --Hopper Volume: (4) Cubic Yards --Cutters: 37 --Drive Motor: 60 HP --Box Dumper / Table --Infeed Conveyor --Discharge Conveyor for Gaylord Box Loading

2019 Vecoplan VHZ1600 | 1300 run hours | Excellent Condition | 2 Available in June of 2025

Vecoplan Model 45/12/2VU HZF Grinder 75 HP Motor 18" Wide opening No Vibrating Infeed conveyor

Low Noise Grinder with Horizontal Feed; 50 HP Main drive motor, 16" diameter rotor with (24) 40 x 40 cutters; top & bottom knurled infeed rolls control feeding. -- 5" x 18" Infeed opening; 390 RPM rotor speed. -- Includes: (1) 18" Wide x 6" deep x 16' long vibratory horizontal infeed conveyor; sizing screen with 7/16" screen hole. -- Approximately 10,163 hrs on this unit.

This Grinder was recently taken out of service and was running good. No electrical controls. Ready to load.

This Grinder was recently just taken out of service. It ran very good before taken out. Does not include electrical controls.

VECOPLAN RG 70/200K Shredder with Steel Belt Conveyor & Dust CollectorSpecifications: -- Hopper Opening: 70″ x 80″ -- Hopper Volume: 4 – 6-1/2 Cubic Yards -- Main motor: 200 HP -- Rotor diameter: 20″ -- Number of cutters: 84 (triple row) -- Size of cutters: 40 mm x 60 mm -- Screen size: Holes 2″ -- Rotor speed: 145 RPM -- Rotor diameter: 20″ -- Hydraulic Feed Ram: 10 HP - 2-Speed -- Throughput: 2,000 – 28,000 Lbs/HrEquipped with: -- 10 HP Motor Dust Collector -- 48″ W kW SCHMIDT Shredder Infeed Conveyor w/ 20′ pit section

VECTOR REVOLUTION - 180, ...CNC Contour Edgebander + Vector Vision UpgradeNumerically controlled automatic Edgebanding Machine precisely applies ABS & PVC edgebanding automatically to square or irregularly shaped parts as the banding head travels on a bridge gantry along the X - Y & Z axis.Machine FeaturesBanding unit simultaneously rotates on a high precision C-Axis; AC Brushless Servo motors with: Digital drives and linear guides ensure high speeds & accuracy with a smooth acceleration-and-deceleration. -- NO PROGRAMMING required; extremely simple changing from one tape size to another; Operator only has to make simple adjustments like: Setting the start position, glue height, feeding the new width of tape. and adjusting tape guide height. All else is performed by the machine. -- Cartridge Glue System: Glue height is set by positioning a pin in a hole in the index ring setting for the glue dosing rod; standard positions are:16 mm (5/8"); 19 mm (3/4"); 25 mm (1.0"); 28 mm (1-1/8"); and 31 mm (1-1/4") eliminating any need for fine adjustment. -- Working Field:X-Axis 139.7" (3,550 mm); Y axis 72" (1,830 mm); 0.63" - 1.57" (16 - 40 mm) min. - max. material thickness.0.79" (20 mm) Min. external radius & 1.97" (50 mm) min. internal radius, depending on the type of banding materials. 1 mm Minimum banding material thickness & 3 mm maximum banding material thickness. (NOTE: 1 mm PVC is not suitable for butt joints). -- Worktable:Phenolic worktable with embedded vernier scales in X & Y axes allow for simple & flexible positioning of 2-stage vacuum pods. Worktable allows for single or pendulum processing with: (2) 48" x 72" (1,219 x 1,828 mm) Work Zones for processing small to large parts. With average cycle times under (2) minutes, the Contour Edgebander consistently produces quality parts, including 360° lap joints.Workpiece is supported by means of: Vacuum cups sitting on a large flatbed; enables absolute flexibility in positioning pods to ensure the workpiece is held securely. Full vacuum achieved with: 100 cbm/Hr Vacuum Pump. Pump is mounted inside the frame of the machine reducing noise and avoiding airborne dust.Exact workpiece positioning is not critical as the patented VECTOR Revolution 180 Operating System is unaffected by panel position.Patented process is controlled by a simple and intuitive interface that does not require CNC programming. -- Edge Banding Unit:VECTOR Revolution 180 Uses a cartridge & nozzle glue extrusion system, which is ideally suited to this Contour Banding application.Cartridge Glue Nozzle is a closed system, which only heats the glue as it is used. Glue is not exposed to the atmosphere. Result: There is no burning of the glue or discoloration, and the original color of the glue & its properties are maintained.Another benefit of the Glue Nozzle System: Close proximity to the first pressure roller. This means that even when slowing for corners, the glue remains molten until pressed onto the panel by the first pressure

VECTOR REVOLUTION 180 CNC CONTOUR EDGEBANDER + Vector Vision Upgrade: Numerically controlled automatic Edgebanding Machine precisely applies ABS & PVC edgebanding automatically to square or irregularly shaped parts as the banding head travels on a bridge gantry along the "X", "Y" & "Z" axis.Machine Features:The banding unit simultaneously rotates on a high precision "C" axis; AC Brushless Servo motors with digital drives and linear guides ensure high speeds & accuracy with a smooth acceleration-and-deceleration. -- NO PROGRAMMING required, extremely simple changing from one tape size to another, the operator only has to make simple adjustments like setting the start position, the glue height, feed the new width of tape and adjust the tape guide height. All else is taken care of by the machine. -- Cartridge Glue System, glue height is set by positioning a pin in a hole in the index ring setting for the glue dosing rod, standard positions are, 16 mm (5/8"), 19 mm (3/4"), 25 mm (1.0"), 28 mm (1-1/8"), 31 mm (1-1/4") eliminating any need for fine adjustment. -- Working Field:"X" Axis 139.7" (3,550 mm), "Y" axis 72" (1,830 mm), 0.63" - 1.57" (16 - 40 mm) min. - max. material thickness.0.79" (20 mm) Minimum external radius & 1.97" (50 mm) minimum internal radius, depending on the type of banding materials. 1 mm Minimum banding material thickness & 3 mm maximum banding material thickness. (NOTE: 1 mm PVC is not suitable for butt joints). -- Work Table:Phenolic worktable with embedded vernier scales in "X & Y" axis allows for simple & flexible positioning of 2 - stage vacuum pods. The worktable allows for single or pendulum processing with (2) 48" x 72" (1,219 x 1,828 mm) work zones for processing small to large parts. With average cycle times under two minutes, the contour edgebander consistently produces quality parts, including 360° lap joints.The work piece is supported by means of vacuum cups sitting on a large flat bed. This enables absolute flexibility in positioning pods to ensure the workpiece is held securely. Full vacuum is achieved with a 100 m³/Hr vacuum pump. The pump is mounted inside the frame of the machine reducing noise and avoiding airborne dust.Exact workpiece positioning is not critical, as the patented VECTOR Revolution 180 operating system is unaffected by panel position.This patented process is controlled by a simple and intuitive interface that doesn't require CNC programming. -- Edge Banding Unit:The VECTOR Revolution 180 uses a cartridge & nozzle glue extrusion system which is ideally suited to this contour banding application.The cartridge glue nozzle is a closed system which only heats the glue as it is used. The glue is not exposed to the atmosphere. This means there is no burning of the glue or dis-coloration & the original color of the glue & its properties are maintained.Another benefit of the glue nozzle system is its close proximity to the first pressure roller. This means that even when slowing for corners, the