Equipment For Sale

48" 6-knife, horizontal fed, fan discharge

West Salem Vibratory Conveyor.20" wide 12' long. Located in MN #00786

50' West Salem 18" Btm Drops into 19" Btm With Screen S/N 116676 15HP Motor & Drive

3 phase, excellent condition.

Western Machinery Group Profile Grinder Good Condition 3 Phase

Factory refurbished 328 Blower available immediately

WESTERN PNEUMATICS FJW2VS24 Heavy Duty Production Finger Jointer. Right & Left Shaper section:- Cap.: 5/8" - 2" Max. thickness, 1-1/2" - 8" max. width, 5" min. - 36" max. length.Equipped with for right and left side: -- (2) Scoring saws, 7-1/2 HP - 3,600 RPM motors, -- (2) trim saws, 7-1/2 HP - 3,600 RPM motors, --(2) shaper motors, 20 HP - direct drive 3,600 RPM motors. -- 6" Wide WESTERN feed chain, angle transfer conveyor and 15 HP variable speed drive with speeds up to (120) lugs per minute. -- Air Bag Pressure Head with quick change feature & brush holddowns -- APQUIP extrusion type glue applicator with meter mixing system -- Transfer to the assembly press via powered manual corner transfer -- 17' Extra length Assembly Infeed Conveyor with electronic ramp up/down infeed package, powered side alignment rolls and top and bottom pre-assembly rolls. -- Assembly Press: 14' (to be confirmed) finished board length, hydraulic squeeze board press and board ejection; with rapid stop-and-chop 7-1/2 HP heavy duty cutoff saw. With automatic cycling, -- Feed speed varies automatically depending on block and cutoff lengths, 50 - 200 FPM.Pieces advance through the cutoff saw to a moveable limit switch and are cut to length, arranged for continuous assembly, the cut to length piece drops down into a final squeeze chamber while the next piece is cut to length, finished lengths are pushed out hydraulically by the next piece onto material outfeed arms.Includes: -- Set of cutterheads and knivesNOTES: -- Machine for factory rebuilt in 2009 -- Machine will easily run 120 lugs per minute and 200 FPM at the Press -- Equipment has been maintained to factory standards since new -- Parts replacemennt (feed chain, sprocket, fences and more) in 2018 for a total of $28,500 -- Taken out of service in January 2025Riggers are required for loadingSome technical information needs to be confirmed by seller

WESTERN PNEUMATICS HEAVY DUTY FINGER JOINTER WITH THE FOLLOWING EQUIPMENT & FEATURES: -- Right & Left Shaper Section: Thickness Capacity: 3/4" - 2" maximum; Width Capacity: 1-1/2" - 8" maximum; Length Capacity: 5" min. - 36" maximum; -- (2) Scoring Saws with 7-1/2 HP - 3,600 RPM motors; -- (2) Trim Saws with 7-1/2 HP - 3,600 RPM motors; -- (2) Shaper Spindles are hydraulically powered; direct driven @ 3,600 RPM by -- (1) 60 HP Hydraulic Power Unit with (1) cartridge unit per spindle. Hydraulic conversion was performed during the first year of operation. -- Western's 2-1/2" wide feed chain with lugs on 9" centers; 15 HP variable speed drive with up to 120-lug per min feed speeds; with angle transfer conveyor, air bag pressure head with quick-change feature & brush hold-downs -- APQUIP Extrusion Type Glue Applicator complete with mixing system. Currently arranged for 3/8 finger joints including (4) 3/8" glue combs -- Manual Corner Transfer to the assembly section. (allows for inspection and rejection of blocks for poor joint quality, missing proper glue spread, etc. prior to going into assembled boards) -- 12' Pre-Assembly Infeed Conveyor with feed speed ramp up/down; with side alignment rolls and dual top and bottom pre-assembly rolls -- Flying Cutoff Saw operating from below -- Assembly Press: 20' board capacity with hydraulically powered press -- Automatic Cycling Assembly Section: Feed speed varies automatically from 50 to 200 FPM, depending on incoming block lengths. Boards advance through the Cutoff Saw to a moveable limit switch where they are cut to length with a bottom-mounted 7-1/2 HP Flying Cutoff Saw arranged for continuous non-stop assembly. The cut to length board drops down into the squeeze chamber while the next board feeds out and above the preceding board where it is cut to length. Pressed lengths are pushed out onto material outfeed arms by the following board

60" with 200HP Electric Motor

Baghouse (Green) W/ 200HP Blower, 75HP Blower, Catwalk and Steps, down and ready to Load

2024 WESTERN STAR SEMI TRACTOR 44,000 MILES DD16 600 HP ENGINE 18 SPPED 46K REARS 13,300 FRONT AXEL 3:91 GEARS 224 WHEEL BASE 5 YEAR 500K WARRANTY LIKE NEW CONDITION TRAILERS ARE NOT INCLUDED FINANCING AVAILABLE WITH NO MONEY DOWN 3 MONTHS NO PAYMENTS WITH GOOD CREDIT GRANITEHE.COM

2006 Western Star 4900 Log Truck, Cat Engine, Barko 80XLE Loader only a few years old. Clean good running truck.

2007 Western Star 4900FA – 2 Units Available - $20,000 Each -800,000 And 879,000 Miles -Almost New Virgin Tires. -Several New Parts Including, Frame Shocks, Cab, Shocks, Frame Airbags, Cab Airbags, Muffler, Filters, Batteries And More! -Used Daily In A Fleet Until The Business Was Sold.

2016 WESTERN STAR 4900SF SEMI 405,250 MILES DETROIT 600HP 18 SPEED 46K REARS 13.5 FRONT AXEL 2 LINE WET SYSTEM HEADACHE RACK RECENT REAR END GOOD BRAKES AND TIRES 1 OWNER FLEET MAINTAINED FINANCING AVAILABLE WITH NO MONEY DOWN 3 MONTHS NO PAYMENTS WITH GOOD CREDIT GRANITEHE.COM

2022 Western Star 4700SB Grapple Saw Truck -10000 miles -470 Horse DD13 Engine With an Allison Auto Transmission -Copma 650 Crane with 112Ft Vertical Reach -Mecanil SG280 Grapplesaw with 25" Bar -Has its own platform to mount with yard mat space beneath -Extra Large Utility Boxes with locks -Electric and Air Brakes for trailers Truck is loaded and like new!!!! -Pintle Hitch mounted and Extra Receiver Hitch

2019 Western Star 4700 SB Grapple saw truck -34,000 miles -Copma 450 knuckle boom crane reach of 106’ straight vertical -Comes with sg160 and sg280 Mecanil saw heads -Have extra bars and chains for each -Up to date annual boom inspection and also dot inspection

This 2018 Western Star 4700 is powered by a DD13 Detroit engine with an Allison automatic transmission, and 40,000 lbs rear ends. It has 11r24.5 tires on it. The truck has 521,866 miles. The truck is work ready, extremely well taken care of, and not one problem at all. If interested in this truck call Gavin 601/394/7796 Tim 251/366/3237 Kameron 251/242/5493 The truck is located in State Line, Mississippi, 467 St Peter St, 39362

1987 Western Star Log Truck Rebuilt Cat 3406B 13 speed Rear tires at 80%, fronts at 60% Barko 80 loader Using daily

2012 western Star Log Truck Prentice 2124 loader Cummins Def deleted Recent radiator 18 speed True mileage around high 300k tac shows in the 600k Can use hour meter to figure out close true mileage Fresh fluids and rear ends checked Work ready Now using landing loader and no longer need truck