Select For Sale

--In Auction--Starting bid: $100-- Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Infeed to 10" Schurman gang edger; this item belongs with stock #727, which is also listed in our equipment for sale. - Call Jeff for more info at 574-370-5050

Belt, drive system, edger guide system -Call Jeff for more info at 574-370-5050

10D G60 thin kerf double arbor schurman gang edger; this item belongs with stock #729, which is also listed in our equipment for sale. Call Jeff at 574-370-5050 for more info.

6"x42" wide overall, includes infeed and outfeed rollers, working condition

Schurman 6TA48 Combination Edger SN: 2121 3 phase 480 volt (2) 200 HP motors

SCHURMAN SINGLE ARBOR GANG SAW 6" x 60"

9' Sherman Transfer Deck, 16' wide with H78A roof top chain, gear reduction drive, 16' jump up roll case, (9) 24"x6" rolls

Schurman Gang Saw Infeed Positioner

Shurman 6SBA 42 S/N 1171 Gang Edger with 150Hp Motor

Schutte model 280.100 Hammer Mill Includes: 125 HP Motor - 480v Includes: (3) Screens: Approx 1", 3/4", 3/8" (to be confirmed) Includes: Stand

SCHUTTE 280.100 HAMMERMILL -- Type 13100P -- Rotor 24" dia. x 48" wide -- Housing 3/4" thick -- Shaft speed 3,600 rpm -- Heavy duty, statically and dynamically balanced rotor -- (96) Standard notched heat treated hammers 3/8" thick -- Also included; two screens -- Motor 125 HP -- Applications; Planer shavings, dry wood chips, etc. etc.

SCHUTTE-BUFFALO 15 Series, Model 15300 Wood Grinder;Complete with the following components and features: --Carbon Steel Construction. --Rotor approximate 44" diameter x 72" wide. --Approximately 3" wide Swinging Hammers, tip speed 20,700. --Top feed, bottom discharge. --Bottom screen approximate 5040 square inch area. --Clam shell housing. --500 HP, TEFC, 3/60/460 volt, 1785 RPM drive Motor with coupling and shaft guard. --Mounted on a heavy-duty steel Factory Frame. --NOTES: Largest model of the 15 Series. &#9679 Machine weight 16,000 Lbs.

Schutte Swing Hammer Grinder

Schutte Pallet Hog - Model 56-35 heavy duty horizontal hog.   Features 50 inch wide horizontal feed  opening with top and bottom powered rolls; 50  2-way, reversible swinging hammers with hardsurfaced tips ; 250 HP direct drive electric motor; 3/4" thick screen with 1-3/8" diameter holes;    Rear discharge.   Electrical cabinets included.   Hammers are approximately 1-3/4" x 5" x 8".    Serial #0506071.

Grinder. This machine is a Shutte grinder. With Webster vibratory infeed. Item #C625

Schutte Hammer Mill Horizontal Infeed HZF40 w/100HP Electric Motor and Attached Blower

Schutte Hammer Mill 40-HZF with 100HP Electric Motor. No. 172 Attached Blower.

Schutte Hammer Mill #40 S/N 111375-R

SCHUTTE BUFFALO - Model WA16L, ... HammermillModel# WA16L, 3500 RPM, with filtration system and multiple grates for destruction sizes. -- It also includes Electrical panel. -- This system is apart and palletized. All you have to do is pick it up and transport it to you. -- System was in perfect working order when it was taken apart and palletized for transport. -- The system is perfect for the destruction of computer hard drives and different types of media.