Select For Sale

2020 PITTS LT40-LSP, 480'L, 102""W, Single Point Suspension, Steel, 11R24.5 Tires, Tandem Axle, Straight Frame Log Trailer, 40', 4 Spring Hutch Susp, 1st & 6th Bolsters Fixed, 4 Center Bolsters Slide, Lumber Gussets, 11R24.5 Hub Pilot, Maxi Brakes, Grapple Bar, Covered Tandem. Same spec trailer with Hutch Susp $26,900 Head Board adds $1500 All Prices are plus FET

Header, 6 bolsters

25 Ton Contractor Special Neck, 33" Deck Height, Spring Ramps and Beavertail, 44'x102", 26' Flat Load Deck, Full Deck Apitong Floor, 17.5 Tires Prices are plus FET

Aluminum Closed Top, 42X102, Aluminum Floor, Aluminum Top Hinge Back Gate, Extruded Aluminum Top and Bottom Rail, Side Post on 16" Center Settings, Spring Suspension, 22.5, Aluminum Prepainted White Sides, Side Vents 42X96 same specs $43,900 Prices are plus FET

FUSION COUPLER LUMBER YARD FORKS 100" SIDE SHIFT MAST FUSION TINES 1.5X8X48, CARRIAGE 60" WIDE

60" CARRIAGE WITH MAST FOR SMALL WHEEL LOADER FUSION INTERFACE PJB LUMBER YARD FORKS SOLD AS IS TINES 1.5"X8"X48"

100" SIDE SHIFT MAST 48" TINES 60" WIDE CARRIAGE ISO LINKAGE PJB SMALL WHEEL LOADER LUMBER FORKS SOLD AS IS

100" MAST 48" TINES INSTALLED 60" WIDE CARRIAGE FOR CATERPILLAR ISO STYLE COUPLER PJB LUMBER YARD FORKS SOLD AS IS

CONNECTING LINES INCLUDED FOR CATERPILLAR 926M PJB VOLVO STYLE QUICK COUPLER SOLD AS IS

18 CYD CAPACITY BOLT ON CUTTING EDGE PIN ON LUGGING PJB 982M WOOD CHIP BUCKET SOLD AS IS

Complete Player Design Drying System - (2) Touch Screen Controllers - (1) PLC Control Box - (1) 12’ X 20’ Burner – 25 million BTU capacity with tempered sight glass that can run green chips/dust - (1) Burner Auger , Gearbox, and Motor - (1) Burner Blower Fan Assembly and Motor - (1) Player Single Pass Insulated Dryer Drum (12x50), 8” T section track, 28” Trunnions, Drive lubrication system, Sprocket, Chain and Gearbox / Motor (Drum rated for output material volume of 16,000 lbs per hour) - (1) Air Pro 48” Overhung Fan Assembly (ID Fan) (No Motor) ---- (Part# 12113601, Type-IERS615, Serial# 21136,) - (1) 200 HP motor for ID Fan - (1) Beck- Damper Adjustment Arm/Gearbox (ID fan comes with opposed blade inlet damper with a 300 ft-lb Beck actuator and armature) ---- (Model 11-209-155212-04-01---- 120V 1PH / 110VA ) - Piping and dampers for piping - Missing approximately 20’ of Dryer Drum Discharge piping - Missing approximately 20’ of Dryer Drum Recycle piping - System was rated at approx 9.25 Tons/hour

PMK C 1203 Single End Coping/Tenoning Machine -- With the C-1203 Coping Machine you can run stiles first or cope first, this machine using a 5 HP motor has counter rotating spindles to insure chip free coping of either square, single profiled or double profiled parts. -- Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 9.5" wide on the C-1203. -- (2) Counter rotating spindles 1.25" diameter. -- Spindle Speed 7,000 RPM; cycle time approx. (4) seconds. -- Side Pressure Clamp to insure proper alignment with fence. -- Cutter Heads totally enclosed for Safety!

PMK C 1205 Single End Coping Machine -- With the C-1205 Coping Machine you can run your Styles first or run your cope first, this machine using a 7.5 HP motor has counter rotating spindles to insure Chip free coping of either square. -- Single profiled or double profiled parts. Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 13.5" wide on the C-1205. -- Two counter-rotating spindles 1.25" in Diameter. -- Capacity of maximum (2) cutters on stack tooling -- Spindle Speed 7,000 RPM; cycle time approx. (4) Seconds. -- Side Pressure Clamp to insure proper alignment with a fence. -- Cutter Heads totally enclosed for Safety!

Pneumafil Dust Collector Model 135 (13.5-460-8): 150 hp. The round duct enters the collector at 48" Diameter. Dixie Air Dust Collector: Size: 108-12, Type: SPB, 50 HP, Inlet to the motor, circumference is 90".

PNEUMAFIL 13.5-460-8 Reverse Air Dust Collector System;Reverse Air Dust Collector with 42,600CFM at 9 to 1 air cloth ratio, 4,738 square feet of filter area. -- 13-1/2' Dia. round baghouse contains (460) bags - 96" long by 5" dia. filter bags in galvanized cages w/reverse jet bag cleaning. -- Reverse Air from 15 HP blower motor which cycles once a minute over filter bags (rotating plenum covers each row of bags once a minute, reversing the normal air flow direction. -- Reverse Air action back flushes the bags and dislodges wood dust particles collected on the filter media which then fall to the bottom of the 60° funnel hopper for removal), bags are changed via walk-in door.. -- Material handling fan with approx. 48" inlet dia with 150 HP floor mounted motor (covered in a shed); 0.25 HP explosion proof motor for manifold drive. -- Rotary Air Lock, gearmotor driven at the bottom of the hopper feeding and shared horizontal screw type auger (if you want it) with gearmotor drive. -- Features: MOTOTRONICS Soft Start for main motor. FIRETEK Spark Detection System (subject to prior sale with adjacent unit). -- Includes: Explosion doors, sprinkler pipe, interior electrical control panel, support frame, safety ladder, railings, and exterior ductwork.Professional dismantling, rigging, transport and installation is available.NOTE: Unit being sold under this record is pictured on the left side on the first two photos. For the smaller diameter unit on the right side (DIXIE AIR) see record "DO-011266".

Pneumafil Baghouse Model 115-816, 8'Bags, 125HP on Blower with 34" inlet and 30' x 35" outlet.

Pneumafil – New Style 10’ ·· Pneumafil – Old Style 12’, 10’, 8’ ·· Torrit – 8’, 10’, 12’ ·· Carter Day – 10’ or can be cut to less ·· Airlanco – 10’ ·· Mac – 10’ MCF Style ·· Call for Availability

Pneumafil – New Style 10’ ·· Pneumafil – Old Style 12’, 10’, 8’ ·· Torrit – 8’, 10’, 12’ ·· Carter Day – 10’ or can be cut to less ·· Airlanco – 10’ ·· Mac – 10’ MCF Style ·· Call for Availability

The seller of this Pneumafil dust collection system has confirmed that it is in great working/running condition and ready to be loaded! - 150HP - Round duct enters the colletor at 48" diameter

Used but reconditioned Pneumafil Corp. reverse air bag house, sizes range from 12,000 CFM up to approximately 60,000 CFM. Reconditioning includes new paint, new filter bags, rebuilt interior components. Call for pricing.