Equipment For Sale

DMC UNISAND K 1100-I M3 1,100 mm (43.31") 3-Head Wide Belt Sander (Bottom), with Finishing PlatenIMPORTANT BIDDING NOTE: This lot is also part of Lot #017, which is a bulk lot consisting of Lots #017A, 017B, & #017C. If the individual bid amounts for Lots #017A, 017B, & #017C total more than the bulk bid amount for Lot #017, then Lots #017A, 017B, & #017C will be awarded to the high bidder of each lot.Specifications: -- Thickness cap. 4 - 170 mm (0.16" - 6.69"). -- Variable feed speeds 3.5 - 18 MPM (10 - 60 FPM).Equipped with: -- 1st Head: 10"; Dia Grooved steel contact roll, with 29 kW (39 HP) Motor. -- 2nd Head: 13"; Dia. Grooved rubber contact roll, with 25.5 kW (34 HP) Motor. -- 3rd Head: 3-1/4"; W Finishing platen, with 21.4 kW (28-1/2 HP) Motor. -- 9 kW (12 HP) Blower. -- 1,115 mm x 2,620 mm (43.90" x 103.15") Abrasive belts, with Pneumatic belt tracking. -- 43"; W x 7’ L Vacuum feed bed for holding thin material flat, with 4 HP Feed motor, 45-1/2"; W x 2’ L I Infeed with 1-7/8"; Dia. rollers on 4-3/4"; Centers, 45-1/2"; W x 8" L Outfeed with 1-7/8"; Dia. rollers on 2-3/8"; Centers. -- Control, with 5-3/4"; LCD Touchscreen, & Motor load meters.Machine Dimensions: 116" x 84" x 81" H.Control Dimensions: 36" x 34" x 82" H.Weight: 8,600 Lbs.

DMC UNISAND K 1100-I M4 1,100 mm (43.31") 4-Head Wide Belt Sander (Top), with Combination & Orbital HeadsIMPORTANT BIDDING NOTE: This lot is also part of Lot #017, which is a bulk lot consisting of Lots #017A, 017B, & #017C. If the individual bid amounts for Lots #017A, 017B, & #017C total more than the bulk bid amount for Lot #017, then Lots #017A, 017B, & #017C will be awarded to the high bidder of each lot.Specifications: -- Thickness cap. 4 - 170 mm (0.16" - 6.69"). -- Variable feed speeds 3.5 - 18 MPM (10 - 60 FPM).Equipped with: -- 1st Head: 10"; Dia Grooved steel contact roll, with 29 kW (39 HP) Motor. -- 2nd Head: 10"; Dia. Grooved rubber contact roll, with 25.5 kW (34 HP) Motor. -- 3rd Head: Combination head, with 6"; Dia. Grooved rubber contact roll, 3-1/4"; w Platen, 3"; Dia. Smooth chromed roll, with 21.4 kW (28-1/2 HP) Motor. -- 4th Head: 9" Orbital head, with 1.27 kW (1-3/4 HP) Motor. -- 8"; Dia. Brush roll, with 0.85 kW (1 HP) Motor. -- 9 kW (12 HP) Blower. -- 1,115 mm x 2,620 mm (43.90" x 103.15") Abrasive belts, with Pneumatic belt tracking. -- 43"; W x 8’ L Vacuum feed bed for holding thin material flat, with 4 HP Feed motor, & 45-1/2"; W x 2' L Outfeed with 1-7/8"; Dia. rollers on 4-3/4"; Centers. -- Digital thickness adjustment. -- Control, with 5-3/4"; LCD Touchscreen, & Motor load meters.Complete with: -- Vertical Air Receiving Tank.Machine Dimensions: 130" x 84" x 91" H.Machine Height with Vertical Air Receiving Tank: 131".Control Dimensions: 36" x 34" x 82" H.Weight: 10,915 Lbs.

156" long x 60" wide x 80" high (3) vertical pneumatic Clamping bars (7) clamps that can be placed horizontal or vertical on perforated surface

This unit has been in storage for some time and will need some TLC.

DANCKAERT - 44 , ...ResawAir Strain 44"; x 5"; Bandsaw.Features & Specifications: -- McDONOUGH Center Split Feed Works. -- Wheel is supported on both sides - not cantilevered. -- Pressured guides. -- McDONOUGH Infeed Rolls. -- Max. Cut: 14";. -- New Dynamic brake. -- 60 & 100 HP. -- Control Cabinet (has battery backup and resistors to prevent spikes). -- Infeed & outfeed systems are the same. -- 24 ft. Long Camel Back chain (has air bags that are controlled by photo cell to raise & lower and index 1-board at a time). -- Max. length of lumber: 24 ft.From Seller: "The machine has a new VFDD 100 HP and a new WEG Severe Service 60 HP motor. All new hydraulic motors, caramel back chain, and roll cases."NOTE: Needs hydraulic unit.

(5) Danfoss VLT-5000 VFD 50Hp Max

3/4 HP 1725 rpm motor 115/208/230 volt single phase approx. 12” x 30” table Jacobs chuck approx. 3/4” footpedal Assorted fixtures and tooling as pictured.

Grinder feeds a holding tank, which the material is automatic metered and feed to the furnace. Feed is temperature controlled.

Custom-Built DEIMCO Through Feed Sprayer with a BLASDEL IR Preheat Tunnel that is available MARCH of 2023. Until then, the System can be seen in operation. -- Line was designed to preheat Fiber Cement board prior to painting and is followed by a Single-Arm Reciprocating Sprayer with 4-Spray Gun cap. Spray Guns not included.SEE ATTACHED VIDEO FOR A GOOD LOOK AT THE LINE's OPERATION!Built in 2019, the System was used for approx. (2) years; current owner changed their process and no longer requires the equipment.Oven width cap.: 60" Wide, 1-3/4" part height cap.; overall Oven dimension: 84" Wide x 12-1/2' long x 55" high, excluding the Blower & Stack. Line/Conveyor: Variable speed drive, 18.5 FPM to 26 FPM; Reciprocator operates up to 260 FPM and set by the HMI. 2-Zone Oven: -- Zone 1: (2) Upper left side wall/ceiling mounted; 18" x 60" emitters. -- Zone 2: (2) Right upper side wall/ceiling mounted 18" x 60" emitters; 8" clearance between emitters & rolls. Heaters: Natural gas using 7" WC; 480 Volt preheat; TC, FM, flange frame. - Gas Ratings: 360,000 BTUH Max. input ; 100,000 BTUH standby input; Air Exhaust on infeed & Injection Blower on outfeed. Electrical ratings: 26.6 Amps, 480 V - 3 Phase, 60 Hz.Exhaust: 980 CFM, 1 HP Motor.Control Panel: 60 AMP Disconnect switch, ALLEN-BRADLEY "Panel View Plus HM", IEC contactor & High Temp PID exhaust.NOTE: (25) New replacement conveyor rollers & (40) reconditioned rollers for IR Tunnel.DIEMCO Sprayer complete with: (1) Reciprocating Arm holds (4) guns and reads the leading & trailing edge to turn on & off the guns as the parts feed through; best to run full width loads through Sprayer; Overspray funnels into buckets.Spray Guns turn on & off based on the part leading & trailing edge; read by a light curtain on the infeed end.Dims: GFS Spray Cabin: 13' Deep x 8-1/2' wide x 9' high surround the reciprocating arm. - Filter & Exhaust Section: 13' Wide x 3' Deep x 10' High.

DEIMCO MFM-98 ACRYLIC COATING FINISHING SYSTEM: Drying Oven for the purpose of baking and drying the acrylic finish onto lumber and panel products. -- Specifications:3"; dia. x 21.625" long Rollers on 12"; centers; Infeed: 16' long In-feed Conveyor, 10' long Transfer Conveyor, 12' long Oven Conveyor: -- Operator & Machine Control:Built with Allen Bradley/Honeywell Components, MFM Serial: 1177, Voltage: 460V/60 Hz/25 Amp, Air: 1"; NPT 90PSIG. -- Complete With:Electrically Heated Oven; 8 Cool Down Fans; 2 - Hydraulic Lift Tables; Panel Machine with Hydraulic Pump; 15’ Flash Off Conveyor; 40’ Cool Down Conveyor Includes the following for (two) flood coat machines, Conveyor System, Arbors, Paint Pump, Hydraulic Pump, Hydraulic Lift Table -- Complete Over-all Foot Print 175’ long x 50’ wide

DEKKER - VMAX 40: HP Vacuum Pump (Liquid Ring)40 HP Oil sealed, liquid ring, compact motor mounted Vacuum Pump System; 550 CFM; max. 29" Hg. -- Heavy-Duty ConstructionCompact design, small footprint, patented, high efficiency "DX-5" separator eliminates oil carry over concerns; Engineered for continuous operation. -- Extended lifeSeal-fluid is not used as a lubricant.Change interval is not critical, resulting in a minimum of (10,000) Hrs. of continuous operation.Sturdy bearing pedestal mounts to standard NEMA, C-face motor. -- Direct Drive and with:Low speed (1,750 RPM) eliminates the use of V-belts, resulting in very low maintenance and zero downtime.Over the full vacuum range without overheating. Air cooled design and low operating noise level.

DEKKER VMAX VMX1003KA1-00 60 HP 1,000 ACFM Single-Stage Oil-Sealed Liquid Ring Vacuum Pump, with 21,001 Hrs.Specifications: -- Nominal cap. 1,000 ACFM, Max. vacuum pressure 29" Hg. -- Pump speed 960 RPM. -- Approx. oil cap. (37) gallons. -- Max. noise level (at 3 feet) 80 dBA.Equipped with: -- 60 HP - 1,780 RPM TEFC Motor.

LOCATED IN ALLENWOOD, PA

Deloupe Log Trailer w/ Serco 7000 Loader

DELTA - 22-650, ...Single Planer.DELTA/INVICTA 12" Table Top (no stand) Single Planer equipped with: 2 HP motor; 3-knife round cutterhead; with rollers.Capacity of 12"; feed rate of 15-1/2 FPM.250 LBS

Delta RC-63N 24" PLANER WITH SPIRAL CUTTER HEADSpecifications -- 24" x 9" Cap., 5/16" max. material removal, -- 10-1/2" min. part length. -- 15 HP Belt drive motor, -- Spiral Cutting Head -- 5,000 RPM, variable feed speed from 20 - 60 FPM.Equipped with & Features -- Powered raise and lower of 25" x 35" table, -- Sectional chipbreakers, sectional infeed roller & dual outfeed rollers. -- Push button magnetic control, -- Dust hood, & grinding attachment to sharpen helical head knives while on the machine.

DELTA RC-51 PLANER20" x 9" Cap., 7.5 HP motor, 4-knife cutterhead, power raise-and-lower adjustment and fine adjustment thru a convenient hand wheel; variable feed speed 16 - 28 FPM; equipped with sectional chipbreakers, adjustable bed & dual outfeed rollers. Actual model 22460

Delta Table Saw 5 HP 230 volt 3-phase

DELTA - UNISAW: Table SawSpecifications -- 10" Blade dia.; 3 HP - 3,450 RPM motor belt drives 5/8" dia. arbor @ 4,000 RPM; arbor tilts: 0° - 45°. -- 3-1/8" Max. depth @ 90°; 2-1/8" max. depth @ 45°; 25" max. rip cap. to right of blade & 15-1/2" max. to left of blade; 13/16" max. dado width. -- Includes: 27" x 40" Cast iron table; distance front edge of saw to blade 12-1/4"; 34" table height; DELTA Rip Fence; (1) set of dado blades.

Delta Radial Arm Saw