Equipment For Sale

Straight Frame Log Trailer, 40', 4 Spring Hutch Susp, 1st & 6th Bolsters Fixed, 4 Center Bolsters Slide, Lumber Gussets, 11R24.5 Hub Pilot, Maxi Brakes, Grapple Bar, Covered Tandem Same spec trailer with Single Point Susp $28,500 Head Board adds $2025 All Prices are plus FET

25 Ton Contractor Special Neck, 33" Deck Height, Spring Ramps and Beavertail, 44'x102", 26' Flat Load Deck, Full Deck Apitong Floor, 17.5 Tires Prices are plus FET

35 Ton Detach Lowboy, 25' Well, 22" Deck Height, 3' Beavertail w/Hyd Ramps, Air Ride w/Manual Override, 4 Position Ride Height, Battery Backup Strobe Lights, Foldout Outriggers, Load Bearing Covered Wheels, Apitong Wood Floor, Boom and Bucket Trough, 22.5 Tires BTR Spring Ramp $57,300 Spring Ride $48,900 Air Ride $55,500 Honda Power Unit $4300 Price plus FET

55 Ton Detachable Lowboy, 26' Well, 22" Loaded Deck Height, Load Bearing Covered Fenders, Air Ride Lift Rear w/Manual Override, 4 Position Ride Height, Battery Backup, Apitong Wood Floor, Boom and Bucket Trough, 22.5 Tires 25' Well trailer also available for $68,900 Flip Axles adds $17,500 Honda Power Unit adds $4,300 35 Ton and 51 Ton Trailers also available All prices plus F.E.T.

35 Ton, Self Contained Hydraulic Ramps, 33" Deck Height, 8'6" Flat Deck, 27' Lower Deck, 4' Beavertail, Apitong Wood Floor, 17.5 Tires Same trailer with Spring Assisted Ramps $33,500 51 Ton Trailers also available Prices are plus FET

55 Ton Detachable Lowboy, 4th Axle Flip with Covered Fenders and Stobe Lights, 25' Well, 22" Loaded Deck Height, Load Bearing Covered Fenders, Air Ride Lift Rear w/Manual Override, 4 Position Ride Height, Battery Backup, Apitong Wood Floor, Boom and Bucket Trough, 22.5 Tires Trailer without the Flip is $68,900 26' Well trailer also available for $69,500 Honda Power Unit adds $4,300 35 Ton and 51 Ton Trailers also available All prices plus F.E.T.

35 Ton, Contractor Special Neck, Spring Assisted Ramps, 27' Flat Deck, 4' Beavertail, 38" Deck Height, 22.5 Tires, Apitong Wood Floor Same trailer with 22.5 tires, 38" deck height, and Hydraulic Ramps available for $36,900 Same trailer with 17.5 tires, 33" deck height and Spring Ramps available for $33,500 Prices are plus FET

Complete Player Design Drying System - (2) Touch Screen Controllers - (1) PLC Control Box - (1) 12’ X 20’ Burner – 25 million BTU capacity with tempered sight glass that can run green chips/dust - (1) Burner Auger , Gearbox, and Motor - (1) Burner Blower Fan Assembly and Motor - (1) Player Single Pass Insulated Dryer Drum (12x50), 8” T section track, 28” Trunnions, Drive lubrication system, Sprocket, Chain and Gearbox / Motor (Drum rated for output material volume of 16,000 lbs per hour) - (1) Air Pro 48” Overhung Fan Assembly (ID Fan) (No Motor) ---- (Part# 12113601, Type-IERS615, Serial# 21136,) - (1) 200 HP motor for ID Fan - (1) Beck- Damper Adjustment Arm/Gearbox (ID fan comes with opposed blade inlet damper with a 300 ft-lb Beck actuator and armature) ---- (Model 11-209-155212-04-01---- 120V 1PH / 110VA ) - Piping and dampers for piping - Missing approximately 20’ of Dryer Drum Discharge piping - Missing approximately 20’ of Dryer Drum Recycle piping - System was rated at approx 9.25 Tons/hour

PMK C 1205 Single End Coping Machine -- With the C-1205 Coping Machine you can run your Styles first or run your cope first, this machine using a 7.5 HP motor has counter rotating spindles to insure Chip free coping of either square. -- Single profiled or double profiled parts. Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 13.5" wide on the C-1205. -- Two counter-rotating spindles 1.25" in Diameter. -- Capacity of maximum (2) cutters on stack tooling -- Spindle Speed 7,000 RPM; cycle time approx. (4) Seconds. -- Side Pressure Clamp to insure proper alignment with a fence. -- Cutter Heads totally enclosed for Safety!

PMK C 1203 Single End Coping/Tenoning Machine -- With the C-1203 Coping Machine you can run stiles first or cope first, this machine using a 5 HP motor has counter rotating spindles to insure chip free coping of either square, single profiled or double profiled parts. -- Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 9.5" wide on the C-1203. -- (2) Counter rotating spindles 1.25" diameter. -- Spindle Speed 7,000 RPM; cycle time approx. (4) seconds. -- Side Pressure Clamp to insure proper alignment with fence. -- Cutter Heads totally enclosed for Safety!

Pneumafil – New Style 10’ ·· Pneumafil – Old Style 12’, 10’, 8’ ·· Torrit – 8’, 10’, 12’ ·· Carter Day – 10’ or can be cut to less ·· Airlanco – 10’ ·· Mac – 10’ MCF Style ·· Call for Availability

Pneumafil Baghouse Model 115-816, 8'Bags, 125HP on Blower with 34" inlet and 30' x 35" outlet.

Pneumafil 13.5 460-10 304 Stainless Steel Reverse Air Bag House, 5,922 SQ/FT Cloth Media, 47,000 CFM @ 8:1 Air/Cloth Ratio, Very Good Condition, $82,000.00

Used but reconditioned Pneumafil Corp. reverse air bag house, sizes range from 12,000 CFM up to approximately 60,000 CFM. Reconditioning includes new paint, new filter bags, rebuilt interior components. Call for pricing.

The seller has confirmed that this Pneumafil 135 is available. Pneumafil Dust Collector Model 135 (13.5-460-8) 150 hp. The round duct enters the collector at 40" diameter & exits at 64" square

The seller of this Pneumafil dust collection system has confirmed that it is in great working/running condition and ready to be loaded! - 150HP - Round duct enters the colletor at 48" diameter

Pneumafil – New Style 10’ ·· Pneumafil – Old Style 12’, 10’, 8’ ·· Torrit – 8’, 10’, 12’ ·· Carter Day – 10’ or can be cut to less ·· Airlanco – 10’ ·· Mac – 10’ MCF Style ·· Call for Availability

Pneumafil MDL 11.6 Dust Collector S/N 13418

PNEUMAFIL 13.5-460-8 Reverse Air Dust Collector System;Reverse Air Dust Collector with 42,600CFM at 9 to 1 air cloth ratio, 4,738 square feet of filter area. -- 13-1/2' Dia. round baghouse contains (460) bags - 96" long by 5" dia. filter bags in galvanized cages w/reverse jet bag cleaning. -- Reverse Air from 15 HP blower motor which cycles once a minute over filter bags (rotating plenum covers each row of bags once a minute, reversing the normal air flow direction. -- Reverse Air action back flushes the bags and dislodges wood dust particles collected on the filter media which then fall to the bottom of the 60° funnel hopper for removal), bags are changed via walk-in door.. -- Material handling fan with approx. 48" inlet dia with 150 HP floor mounted motor (covered in a shed); 0.25 HP explosion proof motor for manifold drive. -- Rotary Air Lock, gearmotor driven at the bottom of the hopper feeding and shared horizontal screw type auger (if you want it) with gearmotor drive. -- Features: MOTOTRONICS Soft Start for main motor. FIRETEK Spark Detection System (subject to prior sale with adjacent unit). -- Includes: Explosion doors, sprinkler pipe, interior electrical control panel, support frame, safety ladder, railings, and exterior ductwork.Professional dismantling, rigging, transport and installation is available.NOTE: Unit being sold under this record is pictured on the left side on the first two photos. For the smaller diameter unit on the right side (DIXIE AIR) see record "DO-011266".

Pneumafil Dust Collector Model 135 (13.5-460-8): 150 hp. The round duct enters the collector at 48" Diameter. Dixie Air Dust Collector: Size: 108-12, Type: SPB, 50 HP, Inlet to the motor, circumference is 90".