Equipment For Sale

BIESSE ROXYL 5.5 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edgebanding Capacity: Edge thickness for strips min./max. 0.4 - 22 mm (0.02" - 0.87"), coiled material from 0.4 - 3 mm (0.02 - 0.12"); panel thickness from 10 - 60 mm (0.39 - 2.36"), workpiece width min. of 85 mm (3.34"); workpiece length min. 140 mm (5.51"); feed speeds 10 - 14 - 18 - 20 MPM (33 - 46 - 59 - 65 FPM). --Machine Interface:"Roxyl-Matic" Automated machine setup, MS/Windows XP Operating System, floppy drive, and 4 GB HD; USB port, keyboard, and mouse interface. -- Flat Screen (17") with color graphics interface: Programs can be easily created and recalled at will; Graphic interface makes programming easy, icon of each unit may be brought up on the screen to show the operator the status of the unit and the parameters, which can be programmed; Edgebander may be operated manually when required, without necessity to write a program.Machine In-Feed Configuration:Pre-Milling Station "FL-502": (2) LH & RH Rotating NC controlled spindles with automatic center positioning. -- Anti-Adhesive "ADZ-700" Automatic Spray Unit with: Glue release agent preventing glue to adhere to work piece surfaces. -- Infrared Heating Lamp: Preheating workpiece edge to ensure best possible surface adhesion quality of edgebanding material. -- Edge Magazine: Automatic for processing coiled and strip edgebanding material. -- Pressure Section: Servo controlled programmable pressure section with (1) large driven roller and (4) idle rollers.Gluing System:EVA (Hot Melt) "QM-705": Quick premelting granulate with glue roller applicator to cover conventional edgebanding material. -- AirForce "VC-710": High pressure, hot air system to reactivate special pre coated edge material (commonly referred to as laser edge).Workstations:End Trimming Unit "IN-801": Front & rear trimming motors, uni-point swivel 0° - 15° bevel, programmable pneumatic change-over from flush to bevel. -- Rough/Flush Trimming Unit "RS-701": Top/Bottom pre- or flush trimming motors. -- Flush/Bevel/Radius Combination Trimming Unit "RF-400": Servo controlled, (2) Servo motors (one for horizontal tool position, one for tool up/down position); using combination bevel/radius/flush insert knives; pre-positioning of motors by pneumatic air cylinders. -- Corner Rounding Unit "CR-202": (2) Motors for front/back corner and upper & lower edge profiling. -- Profile Scraping Unit "RBK-503": Top/Bottom 2-axis NC programmable knife positioning (i.e. 2 - 3 mm radius) for PVC edges. -- Glue Scraping Unit "RCC-701": Flat, top/bottom, digital positioning indicators, pneumatic controlled for in/out position. -- Buffing Station "SP-501": Top & Bottom buffing motors with 150 mm ( 6") cloth buffing wheel diameter; adjusts in multiple directions. -- Edge Reactivation Unit "PH-700": Top/Bottom hot air blowers to restore original color to profile scraped PVC edge material.Complete with: -- Top Pressure Beam with driven flat belt and program

BIESSE ROXYL 6.0 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) + "AIR FORCE" PUR/EVA GLUING TECHNOLOGY: Features: -- Latest Technology combines productivity, efficiency, and flexibility for all types of edgebanding material."AirForce" emits high temperature compressed air through a slot nozzle directly onto the reactive layer of laser banding. That layer is activated and bonds the banding to the panel fibers.This technology allows changes based on banding colors without any setup. Environmentally friendly providing a “clean - green"; technology that eliminates glue and fumes, which becomes timely & important. -- In addition, it features a conventional EVA (Hot Melt) Gluing System to cover the full range of edgebanding processes in use today!Specifications: -- Edgebanding Capacity: Edge thickness for strips min./max. 0.4 - 22 mm (0.02" - 0.87"), coiled material from 0.4 - 3 mm (0.02 - 0.12"); panel thickness from 10 - 60 mm (0.39 - 2.36"), workpiece width min. of 85 mm (3.34"); workpiece length min. 140 mm (5.51"); feed speeds 10 - 14 - 18 - 20 MPM (33 - 46 - 59 - 65 FPM). -- Machine Controls: "Roxyl-Matic" Automated machine setup, MS/Windows XP Operating System, floppy drive, and 4 GB HD; USB port, keyboard, and mouse interface. -- Flat Screen (17") with color graphics interface: Programs can be easily created and recalled at will; Graphic interface makes programming easy; icons of each unit may be brought up on the screen to show the operator the status of the unit and the parameters, which can be programmed; Edgebander may be operated manually when required, without the necessity to write a program.Machine In-Feed Configuration: -- Pre-Milling Station "FL-502": (2) LH & RH Rotating NC controlled spindles with automatic center positioning. -- Edge Magazine: Automatic for processing coiled and strip edgebanding material + a (2) position vertical Coil Magazine Cart. -- Pressure Section: Servo controlled programmable pressure section with (1) large driven roller and (4) idle rollers.Gluing System: -- EVA (Hot Melt) "QM-705": Quick premelting granulate with glue roller applicator to cover conventional edgebanding material. -- AirForce "VC-710": High pressure, hot air system to reactivate special precoated edge material (commonly referred to as laser edge).Workstations: -- End Trimming Unit "IT90-S": Front & rear trimming motors, uni-point swivel 0° - 15° bevel, programmable pneumatic change-over from flush to bevel. -- Rough/Flush Trimming Unit "RS-100": Top/Bottom pre- or flush trimming motors -- Flush/Bevel/Radius Combination Trimming Unit "RF-400": Servo controlled, (4) Servo motors (one for horizontal tool position, one for tool up/down position); using combination bevel/radius/flush insert knives; pre-positioning of motors by pneumatic air cylinders. -- Anti-Adhesive "ADZ-700" Automatic Spray Unit with: Glue release agent preventing glue to adhere to workpiece's surfaces. -- Corner Rounding Unit "CR-202": (2) Motors for front/back corner a

Manufacturer Specs premill hot glue end trim top/bottom trim corner rounding scraping buffing Computer interface

BIESSE FSE Semi Automatic Dowel Inserter with Boring; 21-Spindle head (spindles on 32 mm centers) fixed horizontally for end boring, -- Equipped with:(8) Glue injectors & dowel inserters,(4) overhead "HD" pneumatic hold-down clamps. -- After the drilling cycle is complete, the head assembly traverses down to the glue & dowel injector line for the glue & dowel injection; quick cycle time. -- PLC function selector control for boring only, inserting only, or boring & inserting. -- Capacity: Handles 8 mm - 10 mm dia., digital indicator for adjustable dowel length from 25 mm - 50 mm, max. boring depth 70 mm. -- Features: Height adjustment w/digital readout for panel thickness, hydraulic brakes for adjustment of boring speed; 2.3 HP - 4,000 RPM motor.Complete with: -- (2) Side fences, front support table w/stop, glue reservoir tank with pressure control & rinsing tank for glue nozzles. -- 4way dowel feeding vibrator, and foot pedal for starting cycle.Note: Only (4) dowel line on the machine, you just need to add more dowel tube

Machine Equipped as follows: NC 410 PC Based Controller Keyboard with Floppy Drive Automatic Strip Feed Magazine Belt Driven Top Pressure Beam Multi-Coiled Infeed Magazine RT63 Pre-Milling Unit SP20 Glue System w/ Pre-Melt Unit Hot Air Gluing system Automatic Infeed Pressure System T45 Front & Rear End Trimming Units w/Tilt RS10 Top & Bottom Rough Trimming Units RF30 Top & Bottom Fine Trimming Units AR10 4 Motor Corner Rounding Trimming Units RB30 Top & Bottom Profile Scraping Units RC10 Top & Bottom Glue Scraping Units SZ30 Top & Bottom Oscillating Buffing Units PH10 Top & Bottom Edge Heaters Specifications: Min. Panel Thickness:....................10mm? Max. Panel Thickness:....................60mm? Height of Edge-Band Material:…..15-65mm? Min. Banding Thickness:.................0.3mm ? Max. Banding Thickness:........ ...... 20mm? Min. Panel Length:...........................150mm? Min. Panel Width:............................ 100mm? Feed Speeds:.................................10-24m./min? Electrics: ......................................... 460-480V 3 Phase

BIESSE SKILL G FT 1536 FLAT TABLE MACHINE (W/ATC/BORING): -- Specifications:5' x 12' "Matrix" Grid phenolic surface for "Nested Base Manufacturing". -- Working Capacity:"X" Axis 148.2" (3,765 mm); "Y" axis 61.4" (1,560 mm); "Z" axis stroke is 12.7" (324 mm); max. material thickness 4.7" (119 mm). -- Positioning Speed:"X" & "Y" Axis 197 FPM (60 MPM); "Z" axis 65.6 FPM (20 MPM)."X" & "Y" Axes use a precision rack & pinion system; "Z" axis uses precision ball screws.All axes movement is on precision linear guides & ways and controlled by digital, brushless AC Servo motors.All motion components are maintained by an automatic lubrication system. -- Work Area:Flat table design with: "Matrix" grid phenolic surface for "Nested Base Manufacturing".(5) External pneumatic pop-up stops for piece positioning at (4) corners of workstations; automatic NC controlled 8-zone vacuum table.Prepared for (optional) "quick fit" vacuum outlets for optional clamping of small or awkward shaped parts; with "quick connect" vacuum outlet for custom vacuum pods & fixtures. -- Boring Unit:(1) 2-1/2 HP (1.7 kW) Motor; variable speed up to 6,000 RPM; Boring unit with: (10) Independent vertical spindles; (7) in "X" axis & (3) in "Y" axis. -- Machining:(1) 16 HP (12 kW) Air-Cooled "HSD" Electro-spindle with: HSK F63 Adaptor; RH & LH rotation; variable speed from 1,000 - 24,000 RPM.(1) 12-Position ride along tool changer for "on the fly" ATC. NC Controlled tool presetting for the measurement of the tool length -- Operator & Machine Control:PC Front-End with: BIESSE "BH 660" + "BiesseWORKS + "WINDOWS "WRT" (Windows Real Time) Operating System'19" LCD Flat screen monitor; Server; full keyboard & mouse all mounted on a mobile cart.Intel(R) Core i CPU; 8 GB RAM memory; 500 GB (SSHD) hard disk; dedicated graphic card; DVD reader; USB ports; Ethernet card for network connection capabilities. -- Complete with:(1) 300 m³/Hr Vacuum Pump; air-conditioned control cabinet; automatic program update according to the tool length.Automatic Lubrication system for linear guides, pads, and recirculating ball screw; universal autotransformer for voltages between 200 - 600 V, 50 / 60 Hz; teleservice capabilities; perimeter safety mats; manuals & documents on CD. -- Options Include:Prearrangement for a "C" axis at a later date. -- Actual Model is BIESSE SKILL 1536 G FT.

BIESSE ROVER K 1531 FT FLAT TABLE MACHINE (W/ATC/BORING): -- Specifications: 5' x 10' "Bridge Gantry" machine with "Phenolic Matrix Grid" table. -- Working Capacity: "X" Axis 122" (3,100 mm), "Y" axis 61.4" (1,560 mm), "Z" axis stroke is 12.5" (320 mm), max. material thickness 6.69" (170 mm). -- Positioning Speed:"X" & "Y" axis 196 FPM (60 MPM), "Z" axis 82 FPM (25 MPM); Vectorial High Speed 278.4 FPM (82 MPM).?"X" & "Y" axes use a precision rack & pinion system, "Z" axis uses precision ball screws.All axes movement is on precision linear guides & ways and controlled by digital brushless AC Servo motors.All motion components are maintained by a lubrication system. -- Work Area:Flat table design with "Phenolic Matrix Grid" worktable that allows for automatic locking using T slots or possible vacuum locking (requires a vacuum pump). The machine has 1 working area with 2 left + 1 front & 1 rear origins, (2) reference pin stops for rear LH area, (3) reference pin stops for front LH area &(2) reference pin for side stops (LH side) -- Boring Unit:"BH 10" boring head, (1) 2.5 HP (1.7 kW) - 2,800 - 6,000 RPM variable speed motor; (5) independent vertical spindles in "X" axis & (5) independent Vertical spindles in "Y" axis. -- Machining:(1) 12 HP (9 kW) Air cooled "HSD" Electro-spindle with HSK F63 adaptor, variable speed from 1,000 - 24,000 RPM.(1) 10-Position ATC tool rack mounted on the end of the machine; NC controlled digital presetting device for the measurement of the tool length. -- Operator Interface:PC Front End with: Biesse "BH 660" + "BiesseWorks" + WINDOWS "WRT" (Windows Real Time) operating system;Intel Core I7 CPU, 8 GB RAM memory, 128 SSD GB hard disk, Dedicated graphic card, DVD burner, USB ports.21.5" LCD Flat screen monitor; full keyboard & mouse all mounted on a mobile cart; Ethernet connection capabilities.BiesseWorks graphic interface with assisted graphic editor used to program machining operations; parametric programming and guided creation of parametric macros Import of CAD and other external software files in DXF and CID3 format; 3D simulation of the tool path, calculation of machining time & the ability to create rotate virtual faces. -- Complete with:(2) "Becker H360/1428" 300 m³/Hr vacuum pumps, Automatic program update according to the tool length touch-off probe. Automatic Lubrication system for linear guides, pads and re-circulating ball screw. Universal Auto-Transformer for voltages between 200-600 V, 50/60 Hz. Hand-held control Pendent.NCE safety system for stand-alone machine with 3 sides access with 4 sides light barriers & Anti-climb over extension on the right side of the base-frame -- Actual Model is BIESSE ROVER K 1531 FT

BIESSE ROXYL 5.5 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) + "AIR FORCE" PUR/EVA GLUING TECHNOLOGY: -- Features: Latest Technology combines productivity, efficiency, and flexibility for all types of edgebanding material. "AirForce" emits high temperature compressed air through a slot nozzle directly onto the reactive layer of laser banding. That layer is activated and bonds the banding to the panel fibers. This technology allows changes based on banding colors without any setup. Environmentally friendly providing a “clean - green"; technology that eliminates glue and fumes, which becomes timely & important now that "AirForce" can use PVC. -- In addition, it features a conventional EVA (Hot Melt) Gluing System to cover the full range of edgebanding processes in use today!Specifications: -- Edgebanding Capacity: Edge thickness for strips min./max. 0.4 - 22 mm (0.02" - 0.87"), coiled material from 0.4 - 3 mm (0.02 - 0.12"); panel thickness from 10 - 60 mm (0.39 - 2.36"), workpiece width min. of 85 mm (3.34"); workpiece length min. 140 mm (5.51"); feed speeds 10 - 14 - 18 - 20 MPM (33 - 46 - 59 - 65 FPM). -- Machine Controls: "Roxyl-Matic" Automated machine setup, MS/Windows XP Operating System, floppy drive, and 4 GB HD; USB port, keyboard, and mouse interface. -- Flat Screen (17") with color graphics interface: Programs can be easily created and recalled at will; Graphic interface makes programming easy, icon of each unit may be brought up on the screen to show the operator the status of the unit and the parameters, which can be programmed; Edgebander may be operated manually when required, without necessity to write a program.Machine In-Feed Configuration: -- Pre-Milling Station "FL-502": (2) LH & RH Rotating NC controlled spindles with automatic center positioning. -- Anti-Adhesive "ADZ-700" Automatic Spray Unit with: Glue release agent preventing glue to adhere to work piece's surfaces. -- Infrared Heating Lamp: Preheating workpiece edge to ensure best possible surface adhesion quality of edgebanding material. -- Edge Magazine: Automatic for processing coiled and strip edgebanding material. -- Pressure Section: Servo controlled programmable pressure section with (1) large driven roller and (4) idle rollers.Gluing System: -- EVA (Hot Melt) "QM-705": Quick premelting granulate with glue roller applicator to cover conventional edgebanding material. -- AirForce "VC-710": High pressure, hot air system to reactivate special pre-coated edge-material (commonly referred to as laser edge).Workstations: -- End Trimming Unit "IN-801": Front & rear trimming motors, uni-point swivel 0° - 15° bevel, programmable pneumatic change-over from flush to bevel. -- Rough/Flush Trimming Unit "RS-701": Top/Bottom pre- or flush trimming motors -- Flush/Bevel/Radius Combination Trimming Unit "RF-400": Servo controlled, (2) Servo motors (one for horizontal tool position, one for tool up/down position); using combination bevel/radius/flush insert knives; pre-posit

BIESSE ROVER 24 FTS FLAT TABLE MACHINE (W/ATC/BORING): -- Specifications: 4' x 10' Flat table design for "Nested Base" processing: Working cap.: X-Axis is 122" (3,100 mm), Y-axis is 49" (1,250 mm), Z-axis is 6.1" (155 mm). -- Worktable:Phenolic "MATRIX" grid vacuum table for FT "Nesting" or single part processing using (optional) pods or jigs; (2) side & (4) rear pop-up pins for easy material location. -- Positioning Speed:X- & Y-axis 262 FPM (80 MPM), Z-axis 98 FPM (30 MPM); "X-axis uses a helical rack & pinion system, Y- & Z-axis use precision ball screws; all axes movement is on precision linear guides & ways & controlled by digital, brushless AC Servo motors; all motion components are maintained by an automatic lubrication system. -- Boring Unit:(1) 4 HP (3.3 kW) - 4,000 RPM motor: (14) independent vertical spindles, (7) in X-axis & (7) in Y-axis; (6) horizontal drills with (2 + 2) in X-axis & (1 + 1) in Y-axis. -- Machining:(1) 16 HP (12 kW) Liquid-cooled vertically mounted HSD electro-spindle router with HSK F63 adaptor, inverter driven 1,000 - 20,000 RPM with max. torque from 12,000 - 20,000 RPM; (1) 6-position "Ride Along" Automatic tool changer for "on-the-fly" ATC. -- Operator & Machine Control:PC Front End with: BIESSE "XP600 + WINDOWS" XP-operating system; 15" color CRT; 40 GB hard drive; full keyboard & mouse; Ethernet connection capabilities; programs can be transferred via diskette or downloaded by wire; built-in 1,500 W air conditioner for constant temperature & dust-free environment. -- Complete with: 11 KVA Stabilized autotransformer for voltages between 220 - 600 V; automatic "forced" lubrication system for guides & ball screw; emergency stop rope & pressure sensitive safety mats that will instantly place machine in "pause cycle" when stepped on; sound absorbing protective head enclosure with debris curtain around bottom edge. -- NO Vacuum Pump is included but let us know if needed we can source a good used unit.

BIESSE ROVER A 1232 CNC MACHINING CENTER (W/ATC/BORING):SpecificationsWorking Field "X" axis: 123.6" (3,140 mm); "Y" axis 50" (1,260 mm); "Z" axis stroke 10.8" (275 mm); max. material thickness 9.6" (245 mm). -- Positioning Speed: "X" Axis 262 FPM (80 MPM); "Y" axis (60 MPM); "Z" axis 82 FPM (25 MPM). -- Worktable(8) Adjustable panel supports with: (4) Lifting bars for heavy panels; (3) vacuum pods per panel support.(2) Independent working areas with: (8) Pneumatic back stops; (2) pneumatic side stops; (2) pneumatic central stops. -- Boring Unit"BH 24" Boring unit with: 4 HP (3 kW) Motor with variable speed from 2,800 - 6,000 RPM; (13) independent vertical spindles with: (8) Spindles in "X" axis; (5) spindles in "Y" axis.(10) Horizontal boring spindles with: (3+3) In "X" axis; (2+2) in "Y" axis.(1) "X" Axis grooving saw for max. 120 mm dia. blade. -- Machining:(1) 17.4 HP (13 kW) Liquid-Cooled, electro-spindle router with: HSK F63 Adaptor; variable speed from 3,000 - 24,000 RPM. Prewired for "C" Axis(25) Total ATC positions with: (1) 13-Position ATC tool plate located at the back of the machine base; (1) 12-position ATC rack mounted on the base of the machine frame. -- Operator Interface:PC Front-End with: BIESSE "BH 660" + "BiesseWORKS" + WINDOWS "7" Operating System; 21" color CRT; full keyboard; mouse; 1.44 MB & CD ROM disk drives.RS 232 & USB ports; Ethernet connection; specific function controls & and Internet trouble shooting capabilities; air conditioning; dust free environment."BiesseWORKS" is a: Multitask Operating System; input/output modules; axes override; (5) axes interpolation; diagnostic graphics aid for programming; machine data; tool management. -- Complete with:(1) 300 cbm/Hr Vacuum Pump; handheld remote control pendant; safety Bump Stop system; scrap conveyor; original documentation; user & maintenance manuals, wiring diagrams, and operation of Numerical Control. Automatic chips removal conveyor. -- Actual Model is: BIESSE "ROVER A 1232"

BIESSE ROVER A 1432 ATS CNC MACHINING CENTER (W/ATC/BORING): Specifications: -- Working Capacity:"X axis 125.9" (3,200 mm), "Y" axis 52" (1,320 mm), "Z" axis stroke 13.7" (350 mm), max material thickness 9.6" (245 mm). -- Positioning speed:"X" 262 FPM (80 MPM), "Y" Axis 196 FPM (60 MPM), "Z" axis 98 FPM (30 MPM);AC Brushless Servo motors with digital drive and linear guides ensure high speeds with a smooth acceleration-and-deceleration. -- Work Table:(6) Tube-less panel supports with (4) lifting bars for heavy panels & (3) ATS vacuum pods per panel support;(6) Pneumatic back stops, (6) pneumatic front stops, (2) pneumatic side stops & (2) pneumatic central stops. -- Boring Unit:4 HP (3 kW) motor with variable speed from 1,500 - 7,500 RPM; (20) "Quick Change" independent vertical spindles with (10) spindles in "X" axis & (10) spindles in "Y" axis;(8) horizontal boring spindles with (2+2) in "X" axis & (2+2) in "Y" axis;(1) "X" Axis grooving saw for max 120 mm dia saw blade. (1) "Y" Axis grooving saw for max 120 mm dia saw blade. -- Machining:(1) 17 HP (13 kW) Liquid Cooled "HSD" electro-spindle router with HSK F63 adaptor, variable speed from 1,500 - 24,000 RPM;(1) 8-Position ATC tool plate located on the machine head for "on the fly" ATC. -- Operator & Machine Control:PC Front End: Biesse "BH 600" + bSOLID + WINDOWS "7" operating system,15" TFT monitor, full standard keyboard & mouse, CD ROM disk drives,RS 232 & USB ports, Ethernet connection, specific function controls & and internet trouble shooting capabilities;Control cabinet with air conditioning & dust free environment."bSOLID" is a multitask operating system, input/output modules, axes override, 4-axes interpolation, diagnostic graphics aid for programming, machine data & tool management. -- Complete with:(1) 100 m³/Hr vacuum pump; automatic lubrication system; original documentation; hand held pendant; safety fences & mats; scrap conveyor; CE mark. -- Actual Model is BIESSE ROVER A 1432 ATS

BIESSE SKILL G FT 1224 FLAT TABLE MACHINE (W/ RAKE/OFFLOADING): -- Specifications:4' x 8' "Matrix" grid phenolic surface for Left-Hand Feed "Nested Base Manufacturing" -- Working capacity:"X" Axis 97" (2,465 mm), "Y" axis 49.6" (1,260 mm), "Z" axis stroke is 12.7" (324 mm), max. material thickness 6.6" (170 mm), "Z" Axis clearance when using Sweep Arm 6.6" (170 mm). -- Positioning Speed:"X" & "Y" Axis 196.8 FPM (60 MPM), "Z" axis 96.4 FPM (20 MPM)."X" & "Y" Axes use a precision rack & pinion system, "Z" axis uses precision ball screws.All axes movement is on precision linear guides & ways and controlled by digital, brushless AC Servo motors.All motion components are maintained by an automatic lubrication system. -- Work area:Flat table design with "Matrix" grid phenolic surface for "Nested Base Manufacturing",The machine has (2) working areas with 2-left origins, 2-right origins, 1 front origin & 1 rear origin.External pneumatic pop-up rails with (1 LH + 1 RH) side rail stops for material positioning.Prepared for (optional) "quick fit" vacuum outlets for optional clamping of small or awkward-shaped parts; with "quick connect" vacuum outlet for custom vacuum pods & fixtures. -- Boring Unit:(1) 4 HP (3 kW) motor with variable speed up to 6,000 RPM: Boring unit with (14) independent vertical spindles, (7) in "X" axis & (7) in "Y" axis. -- Machining:(1) 16.1 HP (12 kW) Liquid-cooled "HSD Electro-Spindle" with HSK F63 adaptor, RH & LH rotation; variable speed from 1,000 - 24,000 RPM.(1) 12-Position Revolving tool changer for "on the fly "ATC", (110 mm) max tool dia. per position & 16.5 LBS (7.5 KG) max. weight per tool (including aggregates). NC controlled Tool Touch-off probe for the measurement of the tool length, max 5.1" (130 mm) tool dia. -- Operator & Machine Control:PC Front End with: Biesse "BH 660" + "Biesse WORKS " + WINDOWS "WRT" (Windows Real-Time) operating system;Air-Conditioned control cabinet, 21.5" LCD Flat screen monitor; server, full keyboard & mouse all mounted on a mobile cart.Intel(R) Core i7 CPU; 8 GB RAM memory; 128 SSD GB hard disk superior; Dedicated graphic card; DVD burner; USB ports; Ethernet card for network connection capabilities."Biesse WORKS" Graphic interface makes full use of the operating methods typical of the Windows operating system: assisted graphic editor used to program machining operations; programming and guided creation of parametric macros.Import of CAD and other external software files in DXF and CID3 format; 3D simulation of the tool path, calculation of machining time & the ability to create rotate virtual faces. -- Complete with:(1) 500 m³/Hr "BECKER" vacuum pump. Universal Auto-Transformer for voltages between 200 - 600 V, 50/60 Hz; Tele-Service capabilities; Perimeter Safety System. -- Options Include: (1) Rake system. (1) NC controlled & powered flat belt outfeed table with vacuum sweeping system. Remote hand-held control pendant/keyboard. Automatic centralized L

BIESSE SKIPPER 100 L CNC MACHINING CENTER (2-HEAD): -- Specifications:Flexible "Top & Bottom" Machining Center that uses an innovative panel handling system. -- Workable part size:"X" axis is 118" (3,000 mm), "Y" axis is 39.4" (1,000 mm), max. part thickness of 2.4" (60 mm).Min. workable part size in "X" axis is 3.5" (90 mm), "Y" axis is 2.7" (70 mm), "Z" axis is .3" (8 mm). -- Worktable:Automatic LH infeed transfer conveyor with belts & rollers, Automatic RH outfeed transfer conveyor with belts & rollers; infeed/outfeed table is "robot ready". -- Positioning Speed:"X" Axis is 394 FPM (120 MPM), "Y" axis 295 FPM (MPM), "Z" axis is 98 FPM (30 MPM). -- Boring units: (1) Top mounted boring block, 4.2 HP (3 kW), 4,000 RPM; (29) vertical spindles, (17) spindles in "X" axis & (12) spindles in "Y" axis; -- (10) Horizontal spindles, (4+4) spindles in "X" axis & (1+1) horizontal spindles in "Y" axis; -- (1) "X" axis grooving saw with 2.2 HP (1.7 kW) motor - 5,000 RPM, 150 mm dia blade. -- (1) Bottom mounted boring block, 4.2 HP (3 kW), 4,000 RPM, (29) vertical spindles, (17) spindles in "X" axis & (12) spindles in "Y" axis; -- (10) Horizontal spindles, (4+4) spindles in "X" axis & (1+1) horizontal spindles in "Y" axis; -- (1) "X" axis grooving saw with 2.2 HP (1.7 kW) motor - 5,000 RPM, 150 mm dia blade. -- Machining:(1) Top mounted 4.8 HP (3.5 kW) electro spindle, 7,000 - 18,000 RPM with RH/LH rotation; HSK D-50 adaptors for manual push button "quick-tool" change, ERC-32 tool holders & RC-32 collets. -- (1) Bottom mounted 4.8 HP (3.5 kW) electro spindle, 7,000 - 18,000 RPM with RH/LH rotation; HSK D-50 adaptors for manual push button "quick-tool" change, ERC-32 tool holders & RC-32 collets. -- Operator Interface: PC Front-End with BIESSE "NC 1000" + Windows "Biesse Work" Operating System; 15" color monitor; international keyboard with soft-touch keypad & industrial mouse.RS-232 serial ports for possible down-loading from an office PC, USB ports; (1) 48x CD ROM drive; all mounted in a separate control console with a built-in 1,500 W air conditioner for constant temperature & dust-free environment. -- Complete with:Universal transformer for voltages from 200 - 600 volts, 50/60 Hz, 3-Phase; automatic lubrication system for guides & ways; sound enclosure and complete set of safety fences/devices; machine docs & manuals. -- Options include:"BiesseWORKS Advanced" Office version with: (2) Hardware keys; pneumatic part clamping with motorized infeed & outfeed transfer conveyors; Software Disclaimer: EX-FACTORY INC. Offers NO warranty or support, written or implied concerning any/all "optional" or "additional" manufacturer or 3rd party software supplied with this machine. All software related issues including relicensing fees/requirements/functionality & training is ultimately the sole responsibility of the "Buyer".Note : Tear down and loading not included

Big Jack Scragg Mill

The listing is for all equipment at a closed sawmill. Everything is ready to be moved ASAP. - Timberline big Jake scragg - 48” front saws - 36” back saws all inserted tooth blades. - 10’ capacity - 60ft infeed with step loader for mill - Dead indeed live outfeed - Numerous belts conveyors. - Home made 3 blade flat edger power infeed and outfeed. - 50 ft barn sweep. - The different log decks one with stop and load. - 2 descramblers. - Bandit whole tree chipper needs motor. Has 800 hours on it was wrecked and only damaged motor and cab a little. - 410 printice loader with self propelled carrier. New motor. A lot of misc electric motors, belts and other parts.

2020 Big John 40RC-8FL Log Trailer Full load series. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2015 Big John Pup Trailer, Brand New Tires, Straight as an Arrow, Center Point Suspension, Only Used 5 years

Big on Dry Thermal Modification Kiln Optional Single or Double Units available! The photos on this listing show the latest kiln installed in the US. The wood treated was 12" wide pine at 190 degrees C. Contact CMS for more details! - Gas boiler system (optional oil or electric) - Quick, efficient installation provided by technicians! - Complete package includes shipping, installation and all drawings fro site preparation. - Approx 10,000-12,000 board foot capacity (depending on lumber size and bundle stacking) on the Double Kiln. - Customer support via internet connection.

This unit is up and running as of August, 2024. The customer is producing mainly: Poplar, Oak and Pine. Capacity: Approx 12,500 board feet

Carolina Machinery Sales (CMS) is proud to offer Thermo-Modification Technology from the Italian manufacturer Big on Dry. ????Big on Dry has improved the Thermo-Modification process with their THERMOWOOD (THW) line and provides complete "turn key" systems. The PLC control systems allow programming for a wide variety off wood applications. This allows the same systems to work with very delicate wood that is hard to treat to thicker wood that will be used for outdoor products. The THW system can also be used as a conventional kiln with steam. Basic systems include: - Kiln completely built with stainless steel and aluminum - Initial humidy of 10-15% is reduced to 5-6% - Loading options: Side or Trolley - Heating options: Gas or Wood Burner - Humidification: Combined Spraying System - Controls: Fully Automatic Controls with PLC - Interface & Software: Allows communication with Big on Dry technicians to provide online support - Complete installation and training in the USA Contact CMS to get a quote for your Thermal Modification system