Equipment For Sale

COSTA KH2 CCCT 1350 Wide Belt Sander, (4) Heads52" Width cap. Drum, Drum, Drum, PlatenHead Configuration:1st Head: Steel contact roll, 9-7/8" dia, 45 HP motor;2nd Head: Rubber covered contact roll, 9-7/8" dia, 45 HP motor.3rd Head: Rubber covered contact roll, 9-7/8" dia. 60 shore, 30 HP motor.4th Head: Finishing Platen, 23 HPSpecifications: -- 53" x 103" Abrasive belts, air blast abrasive belt cleaning, pneumatic belt tensioning with electronic tracking. -- Controls with PLC processor, -- Pneumatic grit compensation with 4-position stops. -- Variable feed speed conveyor with inverter control 16 - 82 FPM.Equipped with & Features -- a Vacuum conveyor bed assembly with a 5.5 HP suction fan and motor. -- Infeed & outfeed spring loaded hold down shoes on all heads. -- Powered raise & lower conveyor bed with LED readout and motor load meters.

COSTA - K7 CCCT 650: 4-Head Wide Belt Sander; working width: 650 mm (25.6"); constant pass line conveyor height.Excellent Veneer & Solid Wood Sander with: (3) Contact Rollers and (1) platen.Head Configuration -- 1st Head: Steel contact roller; 250 mm (9-7/8") diameter; driven by 37 kW (50 HP) motor. - Abrasive belt speed 24 MPS (78 FPS). -- 2nd Head: Rubber-covered contact roller; 250 mm (9-7/8") diameter; Shore hardness 70; driven by 30 kW (40 HP) motor. - Abrasive belt speed 18 MPS (59 FPS). -- 3rd Head: Rubber-covered contact roller; 250 mm (9-7/8") diameter; Shore hardness 70; driven by 22 kW (30 HP) motor. - Abrasive belt speed 18 MPS (59 FPS). -- 3rd Head: Segmented finishing platen, electronically controlled narrow segments conform to panel width & length for thin veneer sanding; driven by 11 kW (15 HP) motor. - Abrasive belt speed: Infinitely variable 3 - 16 MPS (30 - 52 FPS). -- Sanding Belt Info: Abrasive belt; air blast abrasive belt cleaning; pneumatic belt tensioning with: Electronic tracking on all heads. - Grit set system for abrasive belt grit compensation. -- At Outfeed: Brush Roller 180 mm (7"); driven by 1.1 kW (1.5 HP) motor. Equipped with: -- PLC Processor controls with touchscreen; integrated control cabinet. -- Feed System & Conveyor Bed Min./max. working height: 3 - 160 mm (1/8" - 6-5/16"). Variable feed speed conveyor with: Inverter control 4 - 20 MPM (13 - 65 FPM). Constant Pass Line at: 920 mm From floor (36"). Vacuum conveyor bed assembly. Infeed & outfeed spring loaded holddown shoes on all heads. Powered raise & lower of conveyor bed with LED readout.Also included: About ...$15,000 of sanding belt.

2 head brush sander 1350mm wide Vacuum bed panel cleaning

Costa 53" Sander Model 80 CT 1350 Wide Belt Sander (2) Machines available!

Costa Model 81 C 1350 Wide Belt Sander

Log press as pictured Main motor (k) 15 Auxiliary motors (K) 1,5 + 1,5 Operating pressure (Bar) 170 - 210 Hourly production with wood chips and sawdust (kg) 120 - 150 Briquette @ (mm) 70 Briquette Length (mm) 30 - 300 Weight (kg) 1650 2180 Dimensions in millimetres (mm) 1700 1720

Cousins LP2100X Wrapping Machine 115 Volt 1 Phase

Cousins LP-SW Wrapper 115Volt 1 Phase Folded down for shipping

Cousins Stretch Wrapper Model LP-SW s/n 250511-5L 9079

Covel Grinder

CAN-PAK - CD-3000: Complete Can Densifier -- Motor: 25 HP.Dimensions• Height: 9’-2";.• Width: 3’-10";.• Length: 13’-5";.• Machine weight: 8,000 Lbs.• Conveyor weight: 1,000 Lbs.• Conveyor: 11’-5"; High x 20-1/2"; wide x 13’ long.Specifications• 25 HP Power unit.• 460 Volt, 3-phase wiring.• Solid-state programmable controller.• Thermostatically controlled hydraulic oil cooler.• 1 Cubic yard hopper.• 120-gallon hydraulic tank.• 20-1/2"; Wide infeed conveyor with: 3/4 HP Motor. Direct drive gear reducer. Magnetic head pulley. Steel reject chute.

CP MANUFACTURING - CP250: Can Flattener -- 230 V - 3-Phase. -- (1) Blower Tube included. -- Infeed Conveyor. -- Magnetic Separator. -- Up To 2000 Lbs of whole cans.

CP MANUFACTURING - CP100: Can Flattener -- 220 V; 1,200 Lbs per hour. -- Infeed Conveyor. -- Magnetic Separator. -- New belt included.

CP CD1000 CAN DENSIFIER -- 900 to 1,500 Lbs/Hr capacity -- Fully automatic solid-state Controller -- Density: 40 Lbs per cu. ft. allowing 140,000 Lbs in 50' railcars or 40,000 Lbs in 40' Trailers. -- 10 HP - 3/60/208/230/460 Volt Hydraulic Power Unit

CP MANUFACTURING - S100-6-LH-US, ...Screens -- (1) System of (2) Screens -- Very lght Use -- Ordered as part of a Single-Stream Sort System that was designed to run 10 Tons/Hr -- 1-Feed Conveyor -- Each: 14,500 Lbs -- Loaded onto your Truck

SCM - ACTION PT 2500: 8' Automatic Case ClampSpecifications -- Max. standard working dimensions: 2,500 mm L x 700 mm W x 1,200 mm H (98.43" L x 27.56" W x 47.24" H). Min. standard working dimensions: 250 mm L x 150 mm W x 250 mm H (9.84" L x 5.91" W x 9.84" H).Working height: 600 mm (23.62"). -- Vertical pressing force: 15 kN (3,372 Lbs).Equipped with: -- (6) Horizontal pressure devices; (3) on each side. -- Rack & Pinion System with: Brushless motors. -- Front & Rear: Safety light curtains. -- SCHNEIDER ELECTRIC - "MAGELIS": 5-1/2" Color touchscreen control.Complete with: -- 480 DELTA/208Y/120 Step-Down Transformer.

CPM Model 2A2 Vertical Pellet Cooler Rated up to 10 TPH on 1/4" Pellets

Onsrud M Series CNC Router 5'x12' Table Vacuum pump Includes: Nederman S1000 Dust System

Model: CR Onsrud 145M12 [ 3 axis ] - Ready to load! [Fanuc Control](Multi Axis Motion Controller - Power Motion i-MODEL A | FANUC) Machine Size: 231" L x 112" W x 91" H Table Size: 61" x 145" Spindle: 12Hp Spindle Accessories: 3 Vacuum Zones, ATLM System (METROL) Precisely measures the length of your tool and automatically feeds that value into your CNC machine controls. 24,000 RPM

CR Onsrud 288 G18 CNC Router Size: 61" x 288" Machine Head Details: Main Head 18Hp HSK63F w/12 Position ATC 18 Hp Spindle – Powering through materials like a hot knife through butter. Accessories: 40 Hp Dekker V- Maxx Vacuum Pump 24,000 RPM, 12 Tool Capacity, 11" Z- Stroke Machine Table: Zone Plumbed Vacuum System Tool Capacity: Pop Up Part Positioning Pin. Power Requirements: 440 Voltage 60 Cycle 3 Phase