Equipment For Sale

1981 Peterbuilt 359 -324,000 miles -CAT 3406B -15 speed transmission -Jake brake -Mack camel back -38k rears 12k front -Older truck so has its seeps but overall solid rig

2012 Peterbilt 567 ISX 15 500 HP 18 speed 281,882 miles 14,192 hours Non steerable lift Double frame 46 lockers on air track Just had emissions done

Peterbuilt Day cab with Head Ache Rack

2005 Peterbilt with new 600 horse power Cummins motor, 46 locking rears and double frame. 18 speed transmission, $65,000

2020 Peterbilt 567 Sleeper Semi Truck 228,000 miles 565 HP Cummins 1X15 18 speed manual trans 3.36 rears Double frame heavy spec 46,000 rears 13,200 steer 3 stage jake Wet line New clutch by Peterbilt 48" flat top sleeper

2002 Peterbilt 377 Log Truck -3406 E certified rebuilt CAT with warranty -Reman transmission 18 speed -2 rebuilt rear ends -All new breaks -Good tires all the way around -2017 Rotobec elite loader

158000 miles clean truck Paccar mx13 14,600 front end 46,000 rears Locking rear ends also available with a 2020 48’ deloupe tri log trailer for additional cost

2000 Peterbilt 378 Quad Axle 475 Cat Engine 8LL Tranny Henderson 46 Full Lockers 20,400 Original Miles Nice Truck Pup trailer available

2003 Peterson HC5400 Grinder -7700 hours -New set of bananas, grates, and teeth -Has a wireless remote -Rotor recently balanced and serviced -New tires ands wheel bearings on axle -Comes with 25K worth of parts MACHINE RUNS AND WORKS BUT NEEDS A FEW MINOR REPAIRS -Has a hole in the metal plate that covers the rotor -Has a small leak in the fuel tank we currently use an auxiliary tank -Intermittent issue of conveyor not feeding. Believe it is a broken wire

PETERSON PACIFIC 5000G Whole Tree ChipperSpecifications: -- Engine: CAT 3412E 1000 HP Diesel Engine -- 3-Flail, Key Knife system currently set for 5/8 chip sizeRecent rebuild on machine: -- Overhung load adapters both replaced within 1000 hrs -- Fan pump replaced within 1500 hrs -- Swing/ boom pump replaced within 750 hrs -- Stick boom pump replaced within 100 hrs -- Engine computer less than 750 hours -- High pressure fuel pump less than 750 hours -- New radiator last summer -- Update main boom pump & flow divider last fall -- Installed a new seat 2 years ago -- New muffler -- New auxiliary bark pusher pumpEquipped with: -- Spare flail pump -- Spare flail motor -- New feed roll teeth -- Spare belts -- Spare pins -- Seal kits -- Spare clutch

2019 Peterson Pacific 2710D Track Horizontal Grinder, Caterpillar C-18 765 HP, Frame Hours 4,500.00, Caterpillar put in a new engine around 3,500 Hours, Dropped a Ring in the Engine, Has Platinum Engine Rebuilt, Undercarriage is 95%, Wireless Remote Control, Air Compressor, Ready for Work. Machine Weight: Approx. 68,100 lbs Width: 8' 2" Length: 40' 8" Height:11' 1" Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2006 Peterson 4710B Tracked -6720 chassis hours -Remanufactured engine installed on machine as the old clutch destroyed the engine -Done by CAT dealer in NC (GregoryPoole) -Reman engine 530hrs -New clutch installed the same time as reman engine installed -Feeder floor 30-40% life left -Rotor balance is good -New main conveyor belt just installed -New main conveyor head motor installed -New skirting guard deflectors installed under rotor -New set of screens in machine I think they are 3" -New clutch module and harness -New Iqan electrical panel upgrade system installed by Peterson rep -C18 T3 caterpillar 755HP -Twin disc clutch Ready to work

2008 Peterson 5900 Tree Chipper -10560 hours -4000 on complete rebuild -Works as it should -Tires good -Two boxes of key knives

2019 Peterson 5000H Chipper -9500 frame hours -Complete Cat rebuild done at 6800 hours -4 flail -Loader -Tons of service receipts and very clean machine Videos upon request

Product Description 2017 Peterson Pacific 2710D Horizontal Track Grinder, Caterpillar C-18 765 HP, Hours are 7,300, Wireless Remote with 25' Tether Control Cord, Discharge Conveyor has a Metal Pulley, Undercarriage is 90%, Ready for Work. Machine Weight: Approx. 68,100 lbs Width: 8' 2" Length: 40' 8" Height:11' 1" Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2005 Peterson 5410 Grinder -5800 hours -CAT 3412 Engine 1000H.P -Needs a discharge belt -New feed chains -New tip protectors

2014 Peterson 4300B Whole Tree Chipper, Caterpillar C-18 Engine, has 3,000 Original Hours and 6,000 Frame Hours New Wireless Remote, New Turbo, New Pumps, New Infeed Floor, New Chains, 6 Knife Chipper, New Rods on Engine, Completely Rebuilt Engine with 100 Hours, Completely gone through machine Ready to Chip. Weight 52,000 lb Length 35' 9" Width 11' 4" Height, 12' Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2018 Peterson 5710D -1,000 original hours -Owner used very few times -Belts are good -Tracks and Undercarriage are good Like new machine !!!!!

2016 Peterson Pacific 4710B Horizontal Grinder, Caterpillar C-27, 1050 HP, 9000 Hours, 90% Undercarriage, Wireless Remote Control, Ready for Work. Weight 79,000 lbs Length 36 ft 3 in Width 10 ft 9 in Height 11 ft 6 in Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2014 Peterson 4300B -6,000 frame hours -Current hours on engine and rebuild 100(C18) -New rods and mains -New turbos -New pumps -Valves -Infeed floor and chains -6 new knives -New fans -Wiring -Tires are 90% brakes work