Klamath For Sale

Doucet MSP-CR-19-48-15-TRF-C-8-7 Conveyor

Good Condition 3 phase .5 HP motor

DOUCET CLAMP CARRIER 30 SECT X 8 FT 6 IN WIDE (200+) 36" CLAMPS MODEL SRH-1 SX30- 8.5-240-36 SN 87-10-28 Includes: HYD PWR PACK, PANEL FLATTENER Dismantled and ready to load!

- 16.5' long - 16 rotating arms and a total of 288 - 32" clamps

DOUCET - 16-SECTION: Clamp Carrier (Hydraulic)Specifications -- (16) Sections; 8-1/2' width. -- (6) Clamps per section; (86) clamps total. -- 32" Clamp opening (rapid change) with: 2-1/2" High jaws.Complete with: -- 5 HP Hydraulic power pack and motor for rotation. -- Hydraulic clamp tightening. -- Pneumatic overhead panel flattener.NOTE: Tear down included!

DOUCET ERS-96/RS-75/AP-508 MULTI-BLADE PANEL GROOVE/RIP SAW SYSTEM:The Doucet ERS-96/RS-75 Automated Panel GROOVE/RIP Saw System is designed to GROOVE and/or RIP panels as well as edge the sides of core materials. Ideal for plywood, OSB, MDF, HDF and other composite panels.This Line was originally designed for Engineered Flooring Blanks.ERS-96 Grooving Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 96" maximum. Material thickness 0.5" - 0.625" maximumGrooving pattern on 4" centers across the 96" width of panel. Depth and width of groove approx. 3/16" kerf/width by 1/8" deep.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). RS-75 Ripping Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 60" maximum. Strip width cap. 2.5" minimum. Depth of cut 0.25" - 0.75" (6 - 19 mm) maximum.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:Doucet AP-508 Automatic panel feeder with scissor lift to automatically feed panels as needed.5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Operator Interface: Doucet OI/HMI Control System for automatic loading & stacking with minimal human intervention other than a forklift operator to bring in new material and remove the processed parts/strips. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). -- Options Include: (1) Doucet AP-508 Automatic panel feeder with Indexing scissor lift. (1) Cross Transfer Chain Conveyor to feed panels sideways by the long edge through the Groover, max width 96". (1) Cross Transfer Chain Conveyor to feed panels short end wise through the panel RIPSAW, max. width 60" (1) Outfeed Lift Table to automatically stack ripped strips. Maximum weight of stack: approx. 5,000 LBS. -- Actual Model is DOUCET RS-75/ERS-96/AP-508

DOUCET - 8-SECTION, ...Clamp Carrier (Hydraulic). -- (8) Sections, 8-1/2' width. -- (8) Clamps per section, (64) clamps total. -- 42" Clamp opening (rapid change) with 2-1/2" high jaws. Complete with: -- (1) Pneumatic fence w/manual valve. -- 5 HP Hydraulic power pack and motor for rotation. -- Hydraulic clamp tightening; mounted on rail. -- Pneumatic overhead panel flattener.Actual model is: SRH 08-8.5-64-42R.Note: Tear down and loading not included.

DOUCET MFE 300 Lateral chain feeder for moulders and optimizers -- 3'0" x 16'-0" working deck for material length 2'0" - 16'0"; width 2" to 9.5" and thickness 1/2" to 4". -- Feed system: Hydraulic variable speed 50-300 FPM with a 20 HP power unit. In-feed (4) roller accelerator; (2) top steel rollers and (2) bottom drive roller. Additional idler rollers along feed fence to support lumber during feeding. -- Chains: Transport length of lateral chain feeder 3'0". (8) strands of C2060 chains on pneumatic up/down device to release lateral pressure on board when feeding. -- Pedestal: Feeder controls mounted to pedestal with extended cable. Interface relay to stop feeder when moulder is stopped. -- Adjustments: Tool less adjustment handles for quick setups. Easy access to for thickness adjustments at front side of feeder. -- AVAILABLE OPTIONSOne (1) set of four (4) feeding wheels made of steel with hardenedsurface teeth $ 1 000.One (1) set of four (4) feeding flat wheels made of steel, 2" wide insteadof 1" for wide material feeding $ 500.One (1) set of four (4) feeding flat wheels made of steel 1" wide $ N/C.Guiding Tunnel between feeder and moulder,Standard Guiding Tunnel (4' long) $ 1 650.Standard Short Guiding Tunnel (32" long) $ 2 100.Complete Guiding Tunnel (4' long) $ 2 700.Complete Guiding Tunnel with adjustable fence (4' long) $ 3 800.Motorized Guiding Tunnel (4' long) on request.Additional chain transfer length capacity (up to a maximum of 6additional feet) For MFE-300-16 sold per foot $ 1 685. Note: More than 6 add. feet: price upon requestSteel plates between chainsFor MFE-300-16 $ 1 050.Platen chains recommended for softwood speciesFor MFE-300-16 $ 2 850.One (1) additional chain for shorter material down to $ 1 750.18" min. lengthPressurized lateral guide with roller bearing end $ 1 400.Powered lateral guide with roller and side guides on request.Custom working height on request.

DOUCET - BT 3-48: Return Conveyor for Edgebanders with Panel TurnerFor Left-Hand feed Edgebanders with Right-Hand Return Conveyor. -- Receiving table: 66" L x 96" W; Return Conveyor: 48" W with total length of 38'. -- Unit can process: 48" Wide x 108" length. -- Minimum part capacity: 4" x 12" For the side turner.Options Include: -- Side mounted "PT 90" Panel Turner; 22" W x 89" L. -- Panels are turned 90° as part of the transfer process between the Receiving and Return Conveyor, eliminating panel overhang.Actual Model: BT3-48-H30-5-38-D-PT

DOUCET - SRX-6: 6-Section Clamp CarrierSpecifications -- (6) Sections; 8-1/2' wide usable clamping width. -- (9) Clamps per section (approx. total of 54 clamps); with: Quick Attach System. -- 36" Opening clamps; 2-1/2" high x 4" jaw width.Complete with: -- Pneumatic panel flattener. -- 5 HP Hydraulic pump for rotation drive. -- Hydraulic clamp tightener.

DOUCET X 60: Finger Jointer Line for Medium Production"X 60 DG" - Automatic feed Finger Jointer has Chain Feeding System: Driven on the bottom & right-and-left side; feeds board up to 6" max. width. Capacity -- 3/4" - 2" Max. thickness; 1-1/2" - 8" max. width with lugs on 11" centers; 5" min. - 48" max. material length. "X60 Right-Hand Shaper Sections; equipped with: -- 5 HP Trim Saw; 3 HP scoring; 15 HP Shaper motor. -- PLC Controls on Shaper section. -- Dual feed chain with: Lugs on 11" centers; 10 - 75 FPM variable feed speed; 5 HP feed drive. -- Max. width: 8"; Thickness from 3/4" to 3 1/2". -- PLC Controlled extrusion type Glue Applicator with: 12-Gal. tan; sound enclosure & cabinet type base. Transfer to the Assembly Press. Model "MP-32" Assembly Press -- 7' - 10' Max. in automatic mode & up to 20' in manual mode cutoff cap.; automatic cycling; 90 FPM powered infeed flat top chain with side alignment rolls to the pre-assembly tunnel. -- Pieces are fed through with bottom & side chain through the Cutoff Saw to a movable limit switch and cut to length; 5 HP upcutting Cutoff Saw for continuous assembly; 2" x 9" cap. with 14" blade; finished lengths are pushed out by the next piece onto material outfeed arms. -- PLC Controlled Press section;10 HP hydraulic unit; 10,000 Lbs max. pressure. -- Gluing system with pump.System Includes & Supplied with: -- Stainless friction plates on assembly table; board holddown on all (4) sides. -- Automatic ejection of finished board with table. -- 6-Bolt cutterheads for hardwood and softwood.Production Capacity: Approx. 8,000 linear ft./shift or more; based on 12" average infeed length.

Doucet Clamp Carrier Model SRH-40-8.5-240-36 40 Section Clamp 8.5' Wide (240) 2-1/2" x 36" Clamps - Rapid Change Voltage: 480/3/60

Doucet SRH-48L-31-T Return Conveyor for Edgebanders For RIGHT-HAND feed Edgebanders with LEFT-HAND return conveyor. -- SpecificationsMin part sizes on conveyors: 12"; x 12"; -- Min part sizes on conveyors as equipped with panel deviator: 4" x 12" -- Max panel sizes feeding all 4 sides: 66" x 66" -- Max panel sizes feeding long sides: 66" x 96" -- Max panel weight capacity: 150 lb -- Conveyor pass Height: 30-42"; -- Receiving table Minimum speed: 9.14 meters per minute (30ft/min) -- Receiving table Maximum Speed: 27.43 meters per minute (90ft/min) -- Return conveyor speed 18-54 meters per minute(60-80ft/min) -- Variable conveyor speed 30 to 90 feet/min. -- Belt transfer speed is fixed at 180 feet/min and return -- Return conveyor speed is adjustable 60 to 180 feet/min. -- FeaturesPneumatic actuated down-stroke transfer belts which raise and lower to transfer the receiving panel to the return conveyor rollers. 48" wide x 5’ long receiving conveyor with 2" Ø steel rollers covered with black vinyl, 10mm belt driven individually every 3" centers -- 48" wide x 31' long return conveyor with 2" steel rollers covered with black vinyl, 10mm belt driven individually every 3" centers -- Belt transfer device 6" wide featuring 9 transfer belts -- Transfer by-pass switch -- Variable speed switch located on operator console -- One rail located along the return section of the conveyor to support long and narrow pieces, adjustable in height -- A panel deviator to redeploy narrow parts over several rollers -- PT-90 panel turner to return long rectangular panels lengthwise rather after finishing -- Actual Model is Doucet SRH-48L-31-T

DRESSER S450E Road Grader

8.3 Cummings Power Shift 10' 6" Blade 5 Tooth Ripper Inc 3 Teeth New Paint New Meter 6K Hours Estimate

Dressta TD-7H Dozer Winch Only 2200 hours Cummins Fresh service In good shape Work ready

Drott excavator with Detroit engine. Runs and operates. No bucket. Price to sell.

DSI - LD-1: CNC Lockdowel PressSpecifications -- The DSI machine is designed to squeeze Lockdowel hardware into the edge of a predrilled panel. Lockdowel machines: (5+) Have years of actual factory usage and inserts (10s) of thousands of Lockdowels successfully, accurately, and quickly! Features. Heavy-Duty construction. No "compressed air requirements only." Single-phase 120 VAC. - A large powerful drive motor. Rack & Pinion: Movable fence, extruded aluminum beams, and cross members. Solid aluminum fences with full adjustment capability.Benefits. Low cost alternative to those which have horizontal drilling capabilities, and do not want to invest in substantially more expensive machines that both drill & insert.Immensely faster and much more accurate than hammering; Lockdowels in by hand - A (1) or (2) person operation.Up to (8) Lockdowels inserted per machine cycle. Safety: Compact, safe, and accurate. Machine functions are supervised by: Safety rated control system including: 2-handed cycle start operation required. Safety light curtains & conveniently located emergency stop buttons.Operator Interface. The DSI machine includes a large touchscreen for quick data entry and quick accuracy adjustments.Portable: The machine is on Heavy-Duty casters. The infeed table folds down and out of the way.

DSI LD-1 CNC LOCKDOWEL PRESS:Specifications -- The DSI machine is designed to squeeze Lockdowel hardware into the edge of a pre-drilled panel. Our machines have over 5 years of actual factory usage, inserting tens of thousands of Lockdowels successfully, accurately, and quickly!! Features: Heavy duty construction. No compressed air requirements-only single phase 120 VAC. A large powerful drive motor. Rack and pinion movable fence and extruded aluminum beams and cross members. A solid aluminum fences with full adjustment capability.Benefits: A low cost alternative to those which have horizontal drilling capabilities and do not want to invest in the substantially more expensive machines that both drill and insert.Immensely faster, and much more accurate than hammering the Lockdowels in by hand. One or two person operation.Up to 8 Lockdowels inserted per machine cycle. Safety: Compact, Safe, Accurate. Machine functions are supervised by a safety rated control system including: two handed cycle start operation required. Safety light curtains & conveniently located emergency stop buttonsOperator Interface: The DSI machine includes a large touch screen for quick data entry and quick accuracy adjustments.Portable: The machine is on heavy duty casters. The infeed table folds down out of the way.

DUBOIS Vertical Edge Fill System with Micro UV This machine is designed to fill voids and defects in edges for a smooth, quality finish. These coaters are ideal for filling porous open grain panels like oak, veneers, particleboard, and MDF. Compatible with solvent based, water based, and UV fill coating.1.1 One (1) Continuous chain transport system- Top and Bottom chain transport conveyor with speed matching attachment conveyor chain- Aluminum backed chain pads with EPDM covering1.2 Two (2) double sided vertical edge denibber/buffer- Operator side Adjustable up to 12"; wide, back side fixed edge- Post mounted vertical denibber head- 12"; dia. x silicon impregnated scuffing wheel, buffer wheel to be determined- Dust hood with 4"; connection- Vertical head oscillation for even brush wear- Inverter controlled drive provides speed control for brush and oscillation1.3 Two (2) double sided vertical edge fill stations- Operator side Adjustable up to 12"; wide, back side fixed edge- Electric motor driven Applicator and Doctor roll drives- Quick change applicator sleeve design, 1-1/2"; face- Stainless steel distribution pipe with spring tension- 9"; dia. chrome plated reverse roll- Stainless steel catch pan and drain lines- 3/8"; pail mounted pump and agitator- Spring loaded doctor bar, urethane dr. blade- Air cylinder dr. roll engagement with stroke adjuster- Inverter controlled drives provides speed control for applicator and doctorrolls1.4 Edge Cure UV Oven Banks- Each bank to consist of Two (2) double sided Fusion F600 Microwave UVovens- Space for two (2) future double sided Microwave UV Units- Individually adjustable three (3) position lamp power selector switch(300, 400 & 600 w/in.)- Irradiator cooling exhaust fan for each set of four (4)2. Control Panel System- NEMA 12 Hinged Door Enclosure, with disconnect, required fuses, door mounted buttons and cooling fans- Allen Bradley HMI, PLC items included- Top mounted panel cooling fan- Required Inverters· Edge Fill Finishing Machineo Top and Bottom Conveyor driveso Denibber/Buffer Brusheso Denibber/Buffer oscillatorso Applicator Rollso Doctor Rollso Reverse Rollso UV oven Exhaust fansDesign Parameters- Machine is located in Explosion Proof Area- Voltage= 480 V., 3 Ph., 60 Hz.- Design Speed = 70 - 200 FPM- Line height = 36";- Max./Min. Part Width: 12"; / 2";- Max./Min Part Length: 245"; / 24";- Max./Min Part Thickness: 1-1/4"; / 3/8";- Paint Color· Main Frame and Conveyor: Blue / TS White· Guards: safety yellowNotes:- ¼"; product has the potential of being processed in this machine but has less probably of being successful the wider the product.