Equipment For Sale

2 strand transfer deck, 28" wide x 14' long, #80 roller chain, no drive, good condition

Model 3650E with Baker (3) Strand Infeed Deck Excellent condition Hydraulic over electric general factory networks. Hooked up to power and ready to be demonstrated.

BBR-0 | Electric Drives | No Hydraulics | 30 HP Motors | 1992

Brand new...never used...still on the original pallet.

Baker Single Head Band Resaw With Return

Baker Pallet De Stacker

Baker Pallet Notcher 2020 or 2021 Single head 3 stringer Has hyd but was line shaft driven when used Used very little

2016 Baker 3665D Bandsaw Mill Two owner 65HP diesel Loaded 3500 hours New tracks, chains, wheels, sprockets, many hoses and bearings, lots of welding and straightening, new blade guides Spare wheels and parts included

Baker PAQ Resaw Good Working Condition

Accepts material up to 12" x 12" and uses a 12"-wide conveyor Main Drive Motor: 30 HP TEFC Variable feed speed from 0-95 feet (0-29 m) per minute 28" Dynamically balanced solid metal band wheels 4" diameter dust outlet requires 500 CFM REDUCED LOW HOUR MILLWORK MACHINE

12" Baker BBR-O Single Head. 30hp Motor. Located in IA. #C968

Baker Furnace Dry Kiln 110volt 3 phase Excellent condition

Baker Furnace Dry Kiln 110volt 3 phase Excellent condition

Baker 6-head resaw, electric drive, good working condition

Baker 4hd Bandsaw with complete run around. Located in WI. #C952

Baker A single Head Bandsaw with 18hp Kohler motor #00899

2013 Baker M4I DeDuster with hopper infeed and variable speed drive and three 2hp brush heads. Electric complete with 480 voltage, panel, and pedestal mounted start and stop station. $6,500.00

The Baker M4i DeDuster has been designed to be a super-high-performance dust removal machine that will accept and remove sawdust from the highest production multi-head horizontal band resaw today. The M4i DeDuster can operate at over 700 feet per minute! Boards drop into the M4i DeDuster hopper. The hopper’s height adjustment (for the amount of lumber), indexable stops (for the length of the lumber), and adjustable fence (for the width of the lumber) allow you to set it up for the most efficient operation. This virtually eliminates jam-ups. The hopper’s variable-speed conveyor sends the lumber through the M4i DeDuster chamber one piece at a time. The rear height adjustment of the conveyor can be adjusted from a minimum of 24" and up to 34" maximum. Inside the M4i DeDuster chamber, high-speed brushes clean all four sides of the boards. The independently powered brushes are fully adjustable for longer brush life. The specially designed chamber maximizes air flow, directing the dust out the dust chamber instead of back onto the boards. The entire side of the chamber easily opens for full open accessibility. The Baker M4i DeDuster comes with its own electrical panel and a stand-mounted, remote start/stop control station.

This is a slightly used 2022 model 26” air activated chop saw with a 15hp motor wired for 480 voltage. It comes complete with the electric panel and controls. It has a 10’ idler infeed roll case with fence and a 5’ idler outfeed with a 48” stop bar and 4 manual stops.

BAKER Model 3640E Blue Streak Electric Sawmill Like New BAKER Model 3640E Blue Streak Electric Sawmill S/N 07-570. 36” diameter log x 24ft. maximum length 40 HP main motor with 10 HP HPU wired for 460 volts, separate control panel on pedestal to turn the system on/off. Includes an Inline Debarker cutter that travels with the head while it travels down the log. Has the Trailer Package, and 10” wide x 12ft. Roller Conveyor Model BCS-O S/N 07-642 for the outfeed, with manual foot pedals kickers to send the boards to the right or the left, and includes lots of extra sawblades. Current new price over $100,000. This was built in 2007 but has had very little use and has been stored inside. See photos of on our web site. Inventory No.KF1.