Equipment For Sale

COSTA K7 CCCT 650 ... 4-Head Wide Belt Sander, working width 650 mm (25.6") and constant pass line conveyor heightExcellent Veneer and Solid wood sander with (3) Contact rollers and (1) platen.Head Configuration: -- 1st Head: Steel contact roller, 250 mm (9-7/8") diameter, driven by 37 kW (50 HP) motor. Abrasive belt speed 24 m/Sec (78 FPS). -- 2nd Head: Rubber covered contact roller, 250 mm (9-7/8") diameter. Shore hardness 70. Driven by 30 kW (40 HP) motor. Abrasive belt speed 18 m/Sec (59 FPS). -- 3nd Head: Rubber covered contact roller, 250 mm (9-7/8") diameter. Shore hardness 70. Driven by 22 kW (30 HP) motor. Abrasive belt speed 18 m/Sec (59 FPS). -- 3rd Head: Segmented finishing platen, electronically controlled narrow segments conform to panel width and length for thin veneer sanding. Driven by 11 kW (15 HP) motor. Abrasive belt speed infinitely variable 3 - 16 m/Sec (30 - 52 FPS). -- Sanding Belt Info: abrasive belts, air blast abrasive belt cleaning, pneumatic belt tensioning with electronic tracking on all heads. Grit set system for abrasive belt grit compensation. -- At Outfeed: Brush Roller 180 mm (7") driven by 1.1 kW (1.5 HP) motor. Equipped with: -- PLC processor controls with touch screen. Integrated control cabinet. -- Feed System & Conveyor Bed: Min/max. working height 3 - 160 mm (1/8" - 6-5/16"). Variable feed speed conveyor with inverter control 4 - 20 m/Min (13 - 65 FPM). Constant Pass Line at 920 mm from floor (36"). Vacuum conveyor bed assembly. Infeed & outfeed spring loaded hold down shoes on all heads. Powered raise & lower of conveyor bed with LED readout.Also inculed: about $15,000 of sanding belt

COSTA - KBH CCCT 1350 & KH2 CCCT 1350, ...Top & Bottom Sander Line.Head Configuration:Machine #1 - "KBH CCCT" 4-Head Bottom Sander. Bottom Head #1: ~10" Dia. grooved Steel Drum, 47 HP motor. Bottom Head #2: ~10" Dia. grooved rubber covered contact drum, 47 HP motor. Bottom Head #3: ~10" Dia. grooved rubber covered contact drum, 32 HP motor. Bottom Head #4: Finishing platen, 23 HP motor.Machine #2 - "KH2 CCCT 1350" 4r-Head Top Wide Belt Sander. Top Head #1: ~10" Diameter Grooved Steel Drum, 47 HP - 460 V motor. Top Head #2: ~10" Grooved rubber covered contact drum, 47 HP motor. Top Head #3: ~10" Grooved rubber covered contact drum, 32 HP motor. Top Head #4: Finishing platen, 23 HP motor.Specifications: -- PC User interface for each machine. -- Sanding belt size: 53" x 103". -- 96" Belt conveyor in between machines. -- 20 HP Vacuum Blower for each machine's vacuum bed.

A. Costa Spamatic 220 Molder

COSTA - KK CC-CCC 1350, ...5-Head Top & Bottom Wide Belt Sander.53" Width capacity; (2) Bottom drums, (3) Top drums.Bottom Machine: -- Constant pass line height: 1,000 mm (39"). -- Motorized infeed conveyor. -- Motorized infeed pressure rollers. -- Sectioned infeed pressure beam.1st Head: -- Rubber covered cylinder ,16" dia., 35 kW motor. -- Intermediate pressure shoe with lips and rubber covered rollers.2nd & 3rd Heads: -- Rubber covered cylinder, 16" dia. (2nd head), 52 kW motor (3rd head), 88 kW. -- Outfeed pressure shoe with lip and rubber covered rollers. -- Vacuum Feed Table: 10 HP (7.5 kW) motor. -- Vacuum set pneumatic for (2) levels of vacuum pull control.Top Machine: -- Infeed roller. -- Motorized infeed pressure rollers. -- Sectioned infeed pressure beam.1st Head: -- Rubber covered cylinder, 16" dia., 35 kW motor. -- Intermediate pressure shoe with lips and rubber covered rollers.2nd & 3rd Heads: -- Rubber covered cylinder, 16" dia. (2nd head), 52 kW motor (3rd head), 88 kW -- Outfeed pressure shoe with lip and rubber covered rollers. -- Vacuum Feed Table - 10 HP (7.5 kW). -- Vacuum set pneumatic for (2) levels of vacuum pull control..Equipped with and Features: -- All drives are equipped with disc brakes. -- Each Sander with vacuum feed belt with fans..

Log press as pictured Main motor (k) 15 Auxiliary motors (K) 1,5 + 1,5 Operating pressure (Bar) 170 - 210 Hourly production with wood chips and sawdust (kg) 120 - 150 Briquette @ (mm) 70 Briquette Length (mm) 30 - 300 Weight (kg) 1650 2180 Dimensions in millimetres (mm) 1700 1720

Cousins LP-SW Wrapper 115Volt 1 Phase Folded down for shipping

Cousins LP2100X Wrapping Machine 115 Volt 1 Phase

Cousins Stretch Wrapper Model LP-SW s/n 250511-5L 9079

Covel Grinder

CP100 Can Flattener --220V, 1200 lbs per hour --Infeed Conveyor --Magnetic Separator -- New belt included

CP CD1000 CAN DENSIFIER -- 900 to 1,500 Lbs/Hr capacity -- Fully automatic solid-state Controller -- Density: 40 Lbs per cu. ft. allowing 140,000 Lbs in 50' railcars or 40,000 Lbs in 40' Trailers. -- 10 HP - 3/60/208/230/460 Volt Hydraulic Power Unit

CAN-PAK - CD-3000: Complete Can Densifier -- Motor: 25 HP.Dimensions• Height: 9’-2";.• Width: 3’-10";.• Length: 13’-5";.• Machine weight: 8,000 Lbs.• Conveyor weight: 1,000 Lbs.• Conveyor: 11’-5"; High x 20-1/2"; wide x 13’ long.Specifications• 25 HP Power unit.• 460 Volt, 3-phase wiring.• Solid-state programmable controller.• Thermostatically controlled hydraulic oil cooler.• 1 Cubic yard hopper.• 120-gallon hydraulic tank.• 20-1/2"; Wide infeed conveyor with: 3/4 HP Motor. Direct drive gear reducer. Magnetic head pulley. Steel reject chute.

CP MANUFACTURING - S100-6-LH-US, ...Screens -- (1) System of (2) Screens -- Very lght Use -- Ordered as part of a Single-Stream Sort System that was designed to run 10 Tons/Hr -- 1-Feed Conveyor -- Each: 14,500 Lbs -- Loaded onto your Truck

CPM Model 2A2 Vertical Pellet Cooler Rated up to 10 TPH on 1/4" Pellets

CPM Pellet Mill Includes: Feed auger Includes: Cooling tower (needs repair) Includes: (2) Chrome dies for 1/4" and 3/8" 100 HP Main Motor with soft start

Onsrud M Series CNC Router 5'x12' Table Vacuum pump Includes: Nederman S1000 Dust System

CR Onsrud 288 G18 CNC Router Size: 61" x 288" Machine Head Details: Main Head 18Hp HSK63F w/12 Position ATC 18 Hp Spindle – Powering through materials like a hot knife through butter. Accessories: 40 Hp Dekker V- Maxx Vacuum Pump 24,000 RPM, 12 Tool Capacity, 11" Z- Stroke Machine Table: Zone Plumbed Vacuum System Tool Capacity: Pop Up Part Positioning Pin. Power Requirements: 440 Voltage 60 Cycle 3 Phase

CR Onsrud Inverted Router more information to follow

- Dual Supported Gantry: Enhances stability and precision with independent servo motors and drives on both sides. - 18 HP Spindle: High-power, fully programmable, and capable of reaching 24,000 RPM, suitable for a wide range of routing and drilling tasks. - 5'x20' Phenolic Vacuum Grid Table: Ensures superior material hold-down through vacuum zones, ideal for flow-through spoil boards or dedicated fixtures. - Integrated Dust Collection System: Keeps the work area clean with integrated dust extraction hoods for chip removal during operations. - 12-Tool Dynamic Automatic Rotary Tool Changer: Facilitates efficient tool changes, with a fully servo-controlled system for quick transitions between tools. - OSAI PC Front Series Controller: Provides advanced control options with a high-resolution touch screen, PLC capabilities, and compatibility with AlphaCAM for programming automation. - 11-inch Z-Stroke: Suitable for various materials and applications, offering flexibility with under-bridge clearance. - 2-Year Warranty: Includes full parts and labor coverage, ensuring reliability and long-term operational support. Included Options: - 9 Spindle Drilling Block Package: Allows for simultaneous or independent drilling along the X and Y axes. - Pneumatic-Controlled Vacuum Table Switch: Actuated via a push-button or PLC control for precise operation. - 20 KVA Isolation Transformer: Ensures stable power supply and noise filtering for optimal performance.

Model: CR Onsrud 145M12 [ 3 axis ] - Ready to load! Machine Size: 231" L x 112" W x 91" H Table Size: 61" x 145" Spindle: 12Hp Spindle Accessories: 3 Vacuum Zones, ATLM System (METROL) Precisely measures the length of your tool and automatically feeds that value into your CNC machine controls. 24,000 RPM