BioMass Equipment For Sale
572 Results Found
Call for Price
Wood Pellet Manufacturing Plant Equipment;Complete with the following features: -- Design capacity 15 tons per hour. -- (1) Pellet Mill (Pellet Press) – custom built in USA and was producing at a rate of 4½ tons per hour. Comes complete with spare parts. -- WEST SALEM Model 4-4-60S Hammer Mill. -- Bulk storage. -- Conveyors to bagging system. -- Blowers Cyclones & Piping.NOTES: ● Plant was planned for several pellet mills but was shut down due to lack of sales. ● Operated only 3-4 years but has been down for a few years now. ● All equipment remains installed. ● Wood supply was from several sources: processing plants by-product, shavings from planer mills, finger jointing plant, and ground trim blocks. ● No Dryer - Owner using it. ● More details on request. ● Professional rigging is available.
MLS Number 12321010 WEST SALEM WSM5472 Horizontal Grinder -60” Millpower Shaker conveyor/finger screen – deck removed, used to meter flow of material fed by operator and reduce bed depth to make cross belt and head pulley magnets most efficient. -60” Eriez cross belt electro magnet. -Eriez 10K42 kW Silicon Rectifier incorporating: To convert 480 volt, 60 Hz, 3 phase AC to230 volt DC 10,000 watts output Normal convection cooled, full wave bridge circuit Fused AC switch Nema 3r Enclosure -Eries beefy magnet stand to support magnet and chain fall. -60” x 28’6” Slider Bed (Heavy Duty Feeder Type Conveyor) with 8’ section of stainless steel non-magnetic for Eriez cross belt magnet to perform at peak -20”x60” Dodge magnetic head pulley – installed to double up on magnets on conveyor, prior to material entering WSM grinder drag chain feed. Downstream from this is the WSM 5472bh Titan horizontal grinder. Schematics and wiring diagram can be supplied as well. WSM also supplied the chip discharge conveyor and magnetic head pulley and electrical panel with touch screen (by Emerson). Price includes dismantling and loading on buyer's truck. Manuals available for components.
$ 89,900
2004 Wildcat TS616 6'x16' Compost Turner, John Deere 8.1 Diesel with 819hrs. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.
WILLIAMS - Hammer Mill: Half-round Type ConfigurationFeatures: -- 220 HP Main Drive Motor with Belt Drive; complete with Guard. -- 26” x 12” Input Opening. -- Powered Input Pull Rolls -- 4” Main Shaft with Swing Hammers, approx. 3/8” thickness -- Ratchet Lift Access Lid. -- Mounted on Steel Support Structure with Access Platform and Ladder -- Pneumatic Bottom Discharge with built-in Viewing Window in Ducting below the Hammermill (no fan included) -- Electrical Cabinet with Motor Starters -- NOTES: This machine was last utilized to break up virgin dried pulp for further processing. Already been removed from service – ready to load.
WILLIAMS - 60KS, ...Hammermill Crusher -- 200 HP Motor. -- Mill RPM 1,000. -- Feed Opening: 62" x 24". -- Ridge Arm Construction. -- Manual Available. -- Loaded onto your Truck.
Call for Price
SALE PENDING
2005 WOODSMAN 440 TREE CHIPPER 2,743 HOURS CAT ENGINE GOOD FEED CHAIN GOOD DRUM REMOTE CONTROL VERY GOOD CONDITION FINANCING AVAILABLE
Call for Price
Call for Price
Call for Price
MODEL ZTLP 1800 X 1600 Zeno Low Noise Single Shaft Shredder/Chipper Specifications: --Model ZTLP 1800 X 1600 -- Feed opening 70’’ (1800mm) wide x approximately 62’’ (1600mm) long. --24’’ Diameter x 70’’ long single rotor with bolt-on blades. --Hydraulic pusher ram feed. --Shredder driven by a 105 kW (140 hp) --3/60/460 volt --1780 rpm motor --No Control Panel --New in 2005