Equipment For Sale

Plantation Log Trailer, 40', 4" Drop, 11R24.5 Hub Pilot, Single Point Susp, Dead Bolster, Maxi Brakes, Grapple Bar, Covered Tandem Same trailer with Vulcan Scales $30,300 4 Spring Hutch Suspension $24,900 Air Ride $28,500 Headboard $1500 All prices are plus FET

Load Payin Series Log Trailer, 40', 8" Drop, Single Point Susp. with Vulcan Scales, 11R24.5 Tires, Maxi brakes, Heavy Duty Biumper wFull Width Grapple Bar, Heavy Duty Lonck N Go Landing Gear, Covered Tandem. Same trailer with No Scales $26,500 4 Spring Hutch Suspension $25,300 Air Ride $27,900 Headboard $1500 All Prices are plus FET

Excellent condition-well maintained. All operates properly. 20’ well, read deck 8’6” flat space. Spring loaded ramps. 2-speed telescoping landings. Tie-down D-rings. 250/70R22.5 tires. Low boy well height 26” lower than most of this design made to fit most Skidders and Fellerbunchers and other 4 wheel equipment and be at or below 13’6” New 250/70R22.5 tires. New Brakes. All new rear LED lights.

2020 PITTS LB35-33 Hydraulic Ramps, 504'L, 102""W, 4 Spring Suspension, Steel, 235/17.5 hub pilot Tires, Tandem Axle, Apitong Floor, 35 Ton, Self Contained Hydraulic Ramps, 33"" Loaded Deck Height, 27' Flat Deck, 4' Beavertail, 17.5 Tires, Apitong Wood Floor, Same trailer with Spring assisted Ramps $31,900 Prices are plus FET

PITTS LT40-8L Hutch Spring, 480'L, 102""W, 4 Spring Suspension, Steel, 11R24.5 hubb pilot Tires, Tandem Axle, Load Payin Series Log Trailer, 40', 8"" Drop, 4 Spring Hutch Susp., 11R24.5 Tires, Maxi brakes, Heavy Duty Biumper wFull Width Grapple Bar, Heavy Duty Lonck N Go Landing Gear, Covered Tandem. Same spec trailer with Single Point Susp., $26,500 Single Point Vulcan Scales $29,500 Air Ride $27,900 Head Board adds $1500 All prices are plus FET

35 Ton, Contractor Special Neck, Self Contained Hydraulic Ramps, 27' Flat Deck, 4' Beavertail, 38" Deck Height, Apitong Wood Floor, 22.5 Tires Same trailer with 22.5 tires, 38" deck height, and Spring Ramps available for $32,500 Same trailer with 17.5 tires and 33" deck height available for $37,500 Prices are plus FET

35 Ton Detach Lowboy, 25' Well, 22" Deck Height, 3' Beavertail w/Hyd Ramps, Air Ride w/Manual Override, 4 Position Ride Height, Battery Backup Strobe Lights, Foldout Outriggers, Load Bearing Covered Wheels, Apitong Wood Floor, Boom and Bucket Trough, 22.5 Tires BTR Spring Ramp $57,300 Spring Ride $48,900 Air Ride $52,900 Honda Power Unit $3800 Price plus FET

51 Ton Contractor Special Neck, 33" Loaded Deck Height, Self Contained Hydraulic Ramps, 30' Flat Deck, 8'6" Upper Deck, 4' Beavertail, Apitong Wood Floor, 17.5 Tires Same spec with Spring Ramps call for pricing 35 Ton Trailer also available Prices are plus FET

35 Ton Detach, 25' Well, Foldout Outriggers, Apitong Wood Floor, 22" Loaded Deck Height, Boom and Bucket Trough, Spring Suspension, Open Fender, 22.5 Tires, Battery Backup Strobe Lights Same trailer air ride, covered fenders $52,900.00 13hp Honda Power Unit add $3,800.00 51 Ton and 55 Ton Trailers also available Prices are plus FET

Plantation Log Trailer, 40', 4" Drop, 11R24.5 Hub Pilot, 4 Spring Hutch Susp., Dead Bolster, Maxi Brakes, Grapple Bar, Covered Tandem Same spec trailer with Single Point Suspension $27,200 Single Point Vulcan Scales $30,300 Air Ride $28,500 Headboard add $1500 All prices are plus FET

100" SIDE SHIFT MAST 48" TINES 60" WIDE CARRIAGE ISO LINKAGE PJB SMALL WHEEL LOADER LUMBER FORKS SOLD AS IS

18 CYD CAPACITY BOLT ON CUTTING EDGE PIN ON LUGGING PJB 982M WOOD CHIP BUCKET SOLD AS IS

CONNECTING LINES INCLUDED FOR CATERPILLAR 926M PJB VOLVO STYLE QUICK COUPLER SOLD AS IS

100" MAST 48" TINES INSTALLED 60" WIDE CARRIAGE FOR CATERPILLAR ISO STYLE COUPLER PJB LUMBER YARD FORKS SOLD AS IS

FUSION COUPLER LUMBER YARD FORKS 100" SIDE SHIFT MAST FUSION TINES 1.5X8X48, CARRIAGE 60" WIDE

60" CARRIAGE WITH MAST FOR SMALL WHEEL LOADER FUSION INTERFACE PJB LUMBER YARD FORKS SOLD AS IS TINES 1.5"X8"X48"

Complete Player Design Drying System - (2) Touch Screen Controllers - (1) PLC Control Box - (1) 12’ X 20’ Burner – 25 million BTU capacity with tempered sight glass that can run green chips/dust - (1) Burner Auger , Gearbox, and Motor - (1) Burner Blower Fan Assembly and Motor - (1) Player Single Pass Insulated Dryer Drum (12x50), 8” T section track, 28” Trunnions, Drive lubrication system, Sprocket, Chain and Gearbox / Motor (Drum rated for output material volume of 16,000 lbs per hour) - (1) Air Pro 48” Overhung Fan Assembly (ID Fan) (No Motor) ---- (Part# 12113601, Type-IERS615, Serial# 21136,) - (1) 200 HP motor for ID Fan - (1) Beck- Damper Adjustment Arm/Gearbox (ID fan comes with opposed blade inlet damper with a 300 ft-lb Beck actuator and armature) ---- (Model 11-209-155212-04-01---- 120V 1PH / 110VA ) - Piping and dampers for piping - Missing approximately 20’ of Dryer Drum Discharge piping - Missing approximately 20’ of Dryer Drum Recycle piping - System was rated at approx 9.25 Tons/hour

PMK C 1205 Single End Coping Machine -- With the C-1205 Coping Machine you can run your Styles first or run your cope first, this machine using a 7.5 HP motor has counter rotating spindles to insure Chip free coping of either square. -- Single profiled or double profiled parts. Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 13.5" wide on the C-1205. -- Two counter-rotating spindles 1.25" in Diameter. -- Capacity of maximum (2) cutters on stack tooling -- Spindle Speed 7,000 RPM; cycle time approx. (4) Seconds. -- Side Pressure Clamp to insure proper alignment with a fence. -- Cutter Heads totally enclosed for Safety!

PMK C 1203 Single End Coping/Tenoning Machine -- With the C-1203 Coping Machine you can run stiles first or cope first, this machine using a 5 HP motor has counter rotating spindles to insure chip free coping of either square, single profiled or double profiled parts. -- Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 9.5" wide on the C-1203. -- (2) Counter rotating spindles 1.25" diameter. -- Spindle Speed 7,000 RPM; cycle time approx. (4) seconds. -- Side Pressure Clamp to insure proper alignment with fence. -- Cutter Heads totally enclosed for Safety!

Pneumafil Baghouse Model 115-816, 8'Bags, 125HP on Blower with 34" inlet and 30' x 35" outlet.