Equipment For Sale

36" chain turner, hyd drive, good condition

Mellott 36 Rosser Head Debarker with Controls and 30hp motor on the head.

Mellot Husk Frame 18" Belt No Saw or Motor

18"W belt 22" opening 15' long 74" high, excellent condition

Mellott 16' Grading System w/Dropout Tipple

Mellott Grading Line Start (incomplete)

Mellott 3-Strand Grading Deck

Mellott #6 Log Turner

In stock at factory. New Mellott Model 8 log turner is built for speed and strength capable of turning both up and down. The mast of the turner is constructed of 1/2” flame cut plates and has two heavy rubber down stops to extend the life of the cylinders. Heavy construction and a simple design are used throughout the Model 8 in order to keep maintenance and down time to a minimum. Frame constructed of C10 X 15.3 Lb. channel Pivot shaft is 2 7/16” diameter Pivot bearings are spherical roller bearings Pivot bearings have cast steel housings The Log turning chain is Rc140 The Log turning chain is direct driven by a Eaton 6000 series hydraulic motor The side and bottom chain wear plates are replaceable The turner has dual cylinders to reduce twisting strain of the mast

Mellott Model 7 Log Turner Hydraulic Power Unit Included

Mereen Johnson 424 DC Gang Rip Outfeed Rollers

Mereen Johnson 431-DC Gang Rip Saw

Mereen-Johnson 424 Gang Rip Saw 230V

MEREEN-JOHNSON 424 DC GANG RIP SAW 24 inch width capacity 75 HP arbor motor- 3600 RPM direct drive 5 HP variable speed feed ( new belt ) Four ( 4 ) kick-back finger sets : ( Two ( 2 ) top in-feed, One ( 1 ) bottom in-feed, One ( 1 ) top out-feed ) A new out-board arbor bearing assembly New set of alum bars and rubber slats installed It is wired 480 volts 3 phase . The serial no. is MJ-4709 One saw sleeve and set of spacers ( 6 saw blades ) Cleaned, painted, and checked.

Mereen Johnson 424DC Gang Rip Saw, 36in W, 60hp Elec, S/N MJ-1775

Mereen Johnson 424 Gang Rip Saw

The seller has confirmed that this Mereen Johnson 441 Rip saw is in great working/running cnodition and it is ready to load! - 2004 Cameron Auto Opti-Rip Infeed - Model: 34F-M1 - Serial: OR164 - 100% Servo (only Servo is this Cameron) - Full amp load 81 - 44" W bed - Up to 20 saws can be run on the arbor - No moving blades BUT there are moving lasers Although this one has been pulled from service, they have an identical one still running and available for inspection....

Mereen-Johnson Model 441-DC Gang Rip Saw Capacity: Arbor space 41” Arbor Drive: 75 HP 3600 RPM TEFC motor Feed Drive: HP TEFC variable speed direct; 45’ to 225’ feet per minute Hold Downs & Bed Plate: Four 5” dia. Air loaded high yield idle press rolls Saw Sleeve: One 41” capacity sleeve Dust Collection: Four upper dust pick-ups: two (2) 8” dia., two(2) 4” dia., one lower 4”dia. Pick-up:(requires total 4820 CFM @ 5,000 feet per minute) Swing Arm & Tip-Up Cart: One floor mounted dual shaft swing arm and one tip-up saw sleeve set-up cart Electrical: Arranged for 3 phase, 60 cycle, 460V Cameron Automated Opti-Rip Model #34F-M1 System: Manufacture Year: (2004) Complete with length measurement Tally System 5 infeed belt and chains for feeding a Gang Rip saw up to 41” wide 16 width sensors 3 sets of pinch rolls for short stock 1 fixed & 4 movable laser lights This system feed for 4’ to 16’ max lumber length It feeds from operator right to left Wired 220V; If 440V required, a transformer will be needed

Mereen Johnson 524-DC/SR4 Rip Saw (4) Shifting Saw Blades Infeed & Outfeed Decks Per MFG - Saw was ingrates into: Rip Navigator Scout Deck, Power Table, Servo Laser Stand, Sorting Printer

MEREEN-JOHNSON Model 524-DDCSR 2+4 Double Arbor Gang Rip SawSPECIFICATIONS: -- First Arbor Arranged with Two (2) Independently Adjustable Select Saw Assemblies for Mounting Hogging Blades -- Second Arbor with Four (4) Independently Adjustable Select Saw Assemblies -- Arbor Space 24" -- Thickness Capacity to 1-3/4" with 12" Tooling and 2-3/4" Using 14" Tooling -- Minimum Length 30"Equipped with & Features -- Two (2) M-J Direct Drive Motors 75 HP Each -- Feed Motor 7.5 HP TEFC, 30' to 235' rate with Frequency Inverter Speed Control -- Saw Set Up for Second Party Optimizing System.