Equipment For Sale

Mellott Trash Belt With Drive 44' long x 22" wide

1998 Mellot Mdl 200 Type 11 Rosserhead Debarker S/N 98200381 Out and Ready to Ship

Mellott Rosser Head Debarker w/Cab, Controls, Steps, 30 HP Elec On Head. MDL# 200 S/N# 88200166

Mellott 36 Rosser Head Debarker with Controls and 30hp motor on the head.

Mellott Rosser Head Debarker, Refurbished New Bull Wheel Shaft Bearings, New Keyway on Bull wheels, Hydraulic Hoses, Pantograph to Carry Hoses. Ready to Ship

Mellott 30" x 24' Rollcase w/Electric Drive

Mellott 30" x 18' Rollcase w/Spiral Sweeps & Electric Drive

Mellott 24" x 26' Rollcase w/Spiral Roll Section w/4' 4 Arm Pop Up Transfer w/6' 3 Arm Pop Up Transfer w/Drive

Transfer Belt Built on Mellott rollcase frame • 31" x 12' spiral rollcase built on end • 36" x 25' x 8" sides • 22" pan, 22"

In stock at factory. New Mellott Model 8 log turner is built for speed and strength capable of turning both up and down. The mast of the turner is constructed of 1/2” flame cut plates and has two heavy rubber down stops to extend the life of the cylinders. Heavy construction and a simple design are used throughout the Model 8 in order to keep maintenance and down time to a minimum. Frame constructed of C10 X 15.3 Lb. channel Pivot shaft is 2 7/16” diameter Pivot bearings are spherical roller bearings Pivot bearings have cast steel housings The Log turning chain is Rc140 The Log turning chain is direct driven by a Eaton 6000 series hydraulic motor The side and bottom chain wear plates are replaceable The turner has dual cylinders to reduce twisting strain of the mast

Mellott #6 Log Turner

Mellott # 5 Log Turner

Mellott Chain Log Turner

MLS Number 13567192 Mercodor Industrial Shredder Just under 2 hours of use Shredder with base Outfeed conveyor with permanent magnet belt 2 x 20Hp 480 volt/60Hz Knives 20 mm 5 hooks Machine opening 1200 mmx 600mm Can process trim ends, sawdust and plastic Machine is still set so we may process wood or plastic for samples if required.

6' wheels with 3 reworked blades.

Mereen Johnson 424 Gang Rip Saw

Mereen-Johnson Model 441-DC Gang Rip Saw Capacity: Arbor space 41” Arbor Drive: 75 HP 3600 RPM TEFC motor Feed Drive: HP TEFC variable speed direct; 45’ to 225’ feet per minute Hold Downs & Bed Plate: Four 5” dia. Air loaded high yield idle press rolls Saw Sleeve: One 41” capacity sleeve Dust Collection: Four upper dust pick-ups: two (2) 8” dia., two(2) 4” dia., one lower 4”dia. Pick-up:(requires total 4820 CFM @ 5,000 feet per minute) Swing Arm & Tip-Up Cart: One floor mounted dual shaft swing arm and one tip-up saw sleeve set-up cart Electrical: Arranged for 3 phase, 60 cycle, 460V Cameron Automated Opti-Rip Model #34F-M1 System: Manufacture Year: (2004) Complete with length measurement Tally System 5 infeed belt and chains for feeding a Gang Rip saw up to 41” wide 16 width sensors 3 sets of pinch rolls for short stock 1 fixed & 4 movable laser lights This system feed for 4’ to 16’ max lumber length It feeds from operator right to left Wired 220V; If 440V required, a transformer will be needed

The seller has confirmed that this Mereen Johnson 441 Rip saw is in great working/running cnodition and it is ready to load! - 2004 Cameron Auto Opti-Rip Infeed - Model: 34F-M1 - Serial: OR164 - 100% Servo (only Servo is this Cameron) - Full amp load 81 - 44" W bed - Up to 20 saws can be run on the arbor - No moving blades BUT there are moving lasers Although this one has been pulled from service, they have an identical one still running and available for inspection....

MEREEN-JOHNSON - 431DC, ...Gang Rip Saw: Specifications: -- 31" Arbor width cap., 14" max. dia. tooling, 3-1/2" max thickness. -- Motorized thickness adjustment. -- 29" Min. length for glue joint accuracy and 22" min. for busting only; 6" throat. -- 75 HP - 3,600 RPM TEFC direct drive motor. -- Arbor with disc brake & load meter. -- Arbor lockout on the access door.Equipped with & Features: -- Feed, Chain & Holddown. -- 5 HP Variable feed speed 30 - 150 FPM with adjustable jam protection. -- MEREEN-JOHNSON "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain. --"Quad Life" hardened dip cams. -- Extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips. -- Automatic chain oiler with low-level shutoff. -- (4) 3" Dia. air loaded overhead pressure rolls. -- Full width spring loaded overhead bed plate. -- Pressure rolls & bed plate unit with powered adjustment; scale & pointer for thickness reference; -- Antikickback Finger System with: (1) Lower & (2) Upper on Infeed; (1) upper assembly on outfeed.

Mereen-Johnson 424 DCS Short Stock Gang Rip sawSpecifications -- 24" Arbor cap., -- 14" max. dia. tooling, -- 3-1/2" max. manual thickness adjustment, -- 14" min. length for glue joint accuracy and 22" min. for busting only, -- 6" throat. Equipped with and Features -- 75 HP - 3,600 RPM TEFC Direct drive motor, -- 2-3/16" dia. arbor with disc brake, -- load meter and slip-off outboard bearing. -- Feed & chain: 3 HP Variable feed speed 30 to 170 FPM, -- M-J "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain -- "Quad Life" hardened dip cams -- Extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips --, Automatic chain oiler. -- (4) 3" Dia. air loaded overhead pressure rolls; full width spring loaded overhead bed plate, -- Pressure rolls and bed plate unit with scale & pointer thickness reference; -- Anti-kickback finger system with (1) lower & (2) upper on infeed. -- Sound enclosure, -- (2) Upper dust hoods (1) 10" & (1) 5" dia. and (1) lower 4" dia. hood, -- Requires 3,820 CFM;NOTE: Laser Rack with 10 Lasers