Equipment For Sale

SCHELLING FXH 430/410 FRONT LOAD, AUTOMATIC PANEL SAW: -- Specifications:169" (4,300 mm) Cutting length & 167" (4,250 mm) pull back; 3.9" (99 mm) max. saw blade projection, 23 HP (17 kW) main & 3.5 HP ((2.6 kW) scoring motor. -- Saw Carriage: Electronically controlled saw carriage with rack & pinion drive; variable travel speed 1 - 394 FPM (1 - 120 MPM), constant return of 394 FPM (120 MPM). -- Pusher Fence: Electronically controlled overhead pusher fence, rack & pinion driven on both sides; (9) Gripper clamps that open up to 3.5" (90 mm). -- Forward speed 0 - 262 FPM (0 - 80 MPM), return speed 262 (80 MPM) FPM; travel via brushless AC Servo Drive -- Operator & Machine Control:PC Front-end with Schelling "MCS" + Windows "NT" operating system.17" Color display with SVGA resolution (displays cutting dimensions & patterns w/moving graphics); virtually unlimited storage capacity, standard keyboard & mouse.Ethernet card; 128 MB Ram, 56K modem. Integrated graphical self-diagnostic, remote diagnostics by the factory is possible via dedicated phone line; data input by keyboard or possible direct downloading from office PC.SCHELLING "MCS" software displays simulation of patterns before actual cutting; graphical representations of cut-to-size parts in production shows the operator what to do in "real time". -- Complete with:2,300 mm Long crosscut fence (front-to-back), (2) automatic side/crosscut aligners for up to 87" (2,210 mm) crosscuts, (1) in front & (1) behind pressure beam cut line.(3) Front mounted air floatation tables, each table 24" x 83" (609 x 2,108 mm), rear of machine fully enclosed for safety with man-height safety fencing. -- Actual Model is SCHELLING FXH 430/410

SCHELLING FM-H 330/330 Automatic Panel Saw 129.9" (3,200 mm) Cutting length, 3.3" (85 mm) max. saw blade projection.Specifications & Features: -- 11 kW (15 HP) main & 1.6 kW (2 HP) scoring motor. -- Variable saw carriage travel speed from 0 - 262 FPM (80 MPM), constant return of 262 FPM (80 MPM). -- Electronically controlled overhead program fence with grippers, rack & pinion driven on both sides, forward speed from 0 - 262 FPM (80 MPM), return speed of 262 FPM (80 MPM); (6) Clamps open up to 3.9" (100 mm). -- 1,500 mm Long crosscut fence (front-to-back), (2) side/crosscut aligners for up to 87" crosscuts, (1) in front & (1) behind pressure beam. -- SCHELLING "COMPOSER" operating system; on-board SCHELLING optimizer, color monitor (displays cutting dimensions & patterns w/moving graphics), self-diagnostic, data input by keyboard & mouse or direct downloading from office PC is possible. Complete with: -- (3) Front mounted air float tables for moving panel from rip position to crosscut position; fully enclosed for safety with man-height sheet metal panels & wire screen windows.Specifications subject to verification.

Schneeberger 9 Sculptor Profile GrinderSwiss Made, Schneeberger Automated High Precision Grinder for Finger Joint, router bits, saw blades, straight and milling Cutters. Specifications: -- Grinding Motor: 1,500 - 3,000 RPM. -- Cooling Pump: 2,800 RPM. -- Grinding Wheel Speed: 3,000 - 6,000 RPM. -- Grinding Wheel Diameter: 50 - 200 mm. Grinding Wheel Bore: 30 mm. -- Cross Travel of Grinding Wheel: 200 mm. Vertical Travel of Grinding Wheel: 400 mm. -- Grinding Head: Swivel-able. -- Worktable Travel: 400 mm. -- Coolant Capacity: 25 liters.Dimensions: 1,226 mm length x 1,160 mm width x 1,180 mm height; Weight - 320 kG.10" Width cap., 11.5" dia., max. profile depth 5.5", radial clearance angle up to 35ø, lateral clearance angle up to 15°Equipped with & Features; -- 2 HP - 1,500 RPM motor, variable grinding speed 2,000 - 4,000 RPM, three-sided full jet cooling. -- All std. grinding equipment for HSS grinding, 1-1/2" spindle arbor, (2) wheel flanges, (1) knife holder, and dresser.

--In Auction--Starting bid: $100-- Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Shurman 6SBA 42 S/N 1171 Gang Edger with 150Hp Motor

Schurman 6TA48 Combination Edger SN: 2121 3 phase 480 volt (2) 200 HP motors

SCHURMAN SINGLE ARBOR GANG SAW 6" x 60"

Infeed to 10" Schurman gang edger; this item belongs with stock #727, which is also listed in our equipment for sale. - Call Jeff for more info at 574-370-5050

Schurman Gang Saw Infeed Positioner

9' Sherman Transfer Deck, 16' wide with H78A roof top chain, gear reduction drive, 16' jump up roll case, (9) 24"x6" rolls

Belt, drive system, edger guide system -Call Jeff for more info at 574-370-5050

10D G60 thin kerf double arbor schurman gang edger; this item belongs with stock #729, which is also listed in our equipment for sale. Call Jeff at 574-370-5050 for more info.

6"x42" wide overall, includes infeed and outfeed rollers, working condition

SCHUTTE PULVERIZER COMPANY - Model 40 HZF, ...HammermillComplete with the following major components & features: -- Integrated 18", 4,000 CFM Blower. -- Mellott Vibrating Conveyor -- Main drive motor: 75 HP -- Hammer width approx. 1-1/4" wide. -- 3-1/4" Shaft. -- 24" Dia. Rotor and a tip speed of 22,600. -- 17-1/2" Rotor width. -- 3/4" Main chamber steel.MANUFACTURER'S STATED KEY FEATURES:&#9679 Heavy-Duty plate construction with replaceable liner plates. &#9679 Heavy-Duty grates available in a variety of sizes. &#9679 Heavy-Duty rotor assembly. &#9679 24" dia. x 3" thick flywheel. &#9679 Built-in fan conveys material up to 50' vertically and 100' horizontally.&#9679 Reversible anvil. &#9679 2-Way reversible "raked" hammers pull wood in without feed rolls. NOTES: &#9679 The" HZF Series" Horizontal Trim Scrap Grinder is a high-speed, high production Grinder designed specifically for processing longer lengths of wood scrap such as: Rippings, edging, and trim blocks. Available in (4) standard sizes from 10" to 36" wide.&#9679 Each model features a built-in fan driven off of the main mill shaft, saving energy and valuable floor space while also significantly increasing production.

SCHUTTE 280.100 HAMMERMILL -- Type 13100P -- Rotor 24" dia. x 48" wide -- Housing 3/4" thick -- Shaft speed 3,600 rpm -- Heavy duty, statically and dynamically balanced rotor -- (96) Standard notched heat treated hammers 3/8" thick -- Also included; two screens -- Motor 125 HP -- Applications; Planer shavings, dry wood chips, etc. etc.

Schutte model 280.100 Hammer Mill Includes: 125 HP Motor - 480v Includes: (3) Screens: Approx 1", 3/4", 3/8" (to be confirmed) Includes: Stand

SCHUTTE BUFFALO - Model WA16L, ... HammermillModel# WA16L, 3500 RPM, with filtration system and multiple grates for destruction sizes. -- It also includes Electrical panel. -- This system is apart and palletized. All you have to do is pick it up and transport it to you. -- System was in perfect working order when it was taken apart and palletized for transport. -- The system is perfect for the destruction of computer hard drives and different types of media.

Grinder. This machine is a Shutte grinder. With Webster vibratory infeed. Item #C625

Schutte horizontal hog, replaced shaft w/ blower & motor, heavy duty design (ref #162) Call Amy for more information (928) 723-9449