Equipment For Sale

2004 CENTAURO TA-F-2000 AUTOMATIC HYDRAULIC COPY LATHE

Extremely well-built Edge Sander with 5 HP - 1,200 RPM TEFC Motor. -- (2) 11" x 60" Cast iron platens. -- 10" x 172" Abrasive belt size. -- 0.5 HP oscillation motor to produce (150) oscillations/Min with 1/2" movement. -- (2) 11-1/2" x 62" Cast iron side tables and (1) cast iron end table. -- All tables with 30° tilt up & 45° down. -- 5" Vertical table travel, 5" lateral side table travel and 4-1/2" lateral end table travel. -- Convenient hand wheel adjustment. -- Large 10" dia. x 10-1/2" face direct drive pulley with 4-1/2" dia. x 10-1/2" idle pulley for a huge sanding surface. -- Magnetic controls with overload protection & dust hood with 4" dia. outlet.

Nice CF Nielson BP5500 Press. The plant shut down in 2014. The machine was run again for a test in 2016 and everything was in good working condition. They have the dies and pistons to make round and octogonal logs. - Briquetting press CF Nielsen BP5500 - Dies to make 3’’ round logs and 2½’’ octogonal logs - Lignin dosing system - Water pump to add water if material too dry - Home-made automatic speed adjustment with encoder. - Briquette breaker from CF Nielsen at the end of the cooling line - Home-made flying saw with lenght asjustment at the end of the cooling line too with capability to switch from the saw to the breaker. - Can run up to 1200kg (even 1400kg I think) per hour depending on material and briquette shape - Cooling line can be opened to make pucks also. - 575V AC motors - Installed in 2008 - 10,865 hours

CFORM Edger/Rip Saw - model CKM160 This machine was purchased new and installed the beginning of 2023. It has less than 20 hours. The seller changed applications. Machine is ready to load. Photos coming! Manufacturer information: Double Edgeing & Slicing Cutter the value of lumber with clean edges can often exceed the value of rough-cut boards. In one pass, this Twin Blade Board Edger takes boards fresh off the mill and turns them into clean, square edged lumber. This edger is easy to use, with one fixed blade and one moveable blade that adjusts with a manual dial. Easily select the precise size of lumber you need. Lower the perimeter fence when you need to edge only one side of a board. Features: Movable finger iron platers for safe guidance and protection. Maximum 15 raws circular saws, adjustable distances. Hydraulic upper roller pressure and movable cyclinders. Maximum cutting height (inch)6 5/16?, 4 11/16?

Challenger Model Series 200 to 1000 Slow Speed Wood Grinder w/30hp 480V Motor. Infeed measures 5' Long x 2' Wide x 4' Deep. Footprint measures 7' Tall x 4' Wide x 6' Wide.

This grinder was removed from service in good working condition. It is ready to load/currently in storage 200 HP Main Motor Cutters 117 F-Cutters Screen (4 ) 22" Diameter Wide with 1-1/2" Holes The width is 51” and the height is 17” (infeed opening)

Challenger Grinder with 10' Infeed Steel Belt, On Board Hydraulics.

2017 Challenger 1050 -3,300 hours -Tight and dry unit -Tires are like new -2014 Seppi Maxisoil 350 is a Tiller/Crusher head Turn Key Land clearing Unit !!!!! -

Challenger Grinder as pictured

Unit was (reconditioned) in 2013. Bottom Flail Assembly replaced in 2014. Unit has a remote. CALL FOR DETAILS

Recently replaced the engine

Champion 5 HP 575 Volt 2 Stage 24 CFM unit.

1993 Champion 710A Series 2 -3330 hours -Tires 60% -Motor Cummins -Tight and dry -Ready to work

CHAMPION - HRA25-25, ...Dual Stage Air Compressor. 25 HP Commercial Duty motor; 90.1 CFM at 175 PSI and 250-gal. horizontal tank. -- Features: CHAMPION's "R" Series 2-stage cast iron pump, dome pistons, and disc valves allow for higher performance at lower RPM's; largest roller bearings in the industry. -- The 250-gal. horizontal tank is equipped with: Large pressure gauge, standard tank drain, and a hard painted finish for years of durability. -- Complete with: Large dia. air filters, OSHA approved belt guard. -- Air-cooled aftercooler.

Champion D-565T Motor Grader Rebuilt Engine With Less Than 100 Hours Has A Few Leaks Currently Used As Is For Driveways Manuals Included Runs and Operates Great

Believe Champion Swing Hammer Hog 30"

2013 Fuji Ace Robot with tooling, slip sheet tray, electric panels, safety fencing and loading included. Very nice unit with more pictures coming.

Automatic template Maker for grinding your own Molder knives

Chase (2) saw board edger, 30" wide w/ (1) movable saw w/ 40 HP motor 230/460 V 1765 RPM w/ HD spiked feed rolls, (2) inserted tooth saws, outfeed steel deck table w/ bar sweep to transfer board to discharge belt, (Selling with sawmill, See Chase Sawmill under Circular Sawmill), ref #204, Contact Jackie Kittrell 931-698-3342

Chase Turbine Mfg. Co. Sawyer's Favorite hand set sawmill, immaculate condition (3 HB), wood & steel frame, 40' track, in track mount carriage drive drum & cable, 100 HP 220V head saw motor w/ WEG soft start MCC, include off bear belt on husk frame & outfeed belt conveyor, (1) w/ shaft mount reduction drive, Selling with (See Chase Edger under Edgers)ref #204, Contact Jackie 931-698-3342