Equipment For Sale

25 Ton Contractor Special Neck, 33" Deck Height, Spring Ramps and Beavertail, 44'x102", 26' Flat Load Deck, Full Deck Apitong Floor, 17.5 Tires Prices are plus FET

Straight Frame Log Trailer, 40', 4 Spring Hutch Susp, 1st & 6th Bolsters Fixed, 4 Center Bolsters Slide, Lumber Gussets, 11R24.5 Hub Pilot, Maxi Brakes, Grapple Bar, Covered Tandem Same spec trailer with Single Point Susp $28,500 Head Board adds $2025 All Prices are plus FET

35 Ton, Contractor Special Neck, Self Contained Hydraulic Ramps, 27' Flat Deck, 4' Beavertail, 38" Deck Height, Apitong Wood Floor, 22.5 Tires Same trailer with 22.5 tires, 38" deck height, and Spring Ramps available for $32,500 Same trailer with 17.5 tires and 33" deck height available for $37,500 Prices are plus FET

Load Payin Series Log Trailer, 40', 8" Drop, Single Point Susp. with Vulcan Scales, 11R24.5 Tires, Maxi brakes, Heavy Duty Biumper wFull Width Grapple Bar, Heavy Duty Lonck N Go Landing Gear, Covered Tandem. Same trailer with No Scales $31,900 4 Spring Hutch Suspension $25,300 Air Ride $27,900 Headboard $2025 All Prices are plus FET

55 Ton Detachable Lowboy, 4th Axle Flip with Covered Fenders and Stobe Lights, 25' Well, 22" Loaded Deck Height, Load Bearing Covered Fenders, Air Ride Lift Rear w/Manual Override, 4 Position Ride Height, Battery Backup, Apitong Wood Floor, Boom and Bucket Trough, 22.5 Tires Trailer without the Flip is $68,900 26' Well trailer also available for $69,500 Honda Power Unit adds $4,300 35 Ton and 51 Ton Trailers also available All prices plus F.E.T.

35 Ton, Self Contained Hydraulic Ramps, 33" Deck Height, 8'6" Flat Deck, 27' Lower Deck, 4' Beavertail, Apitong Wood Floor, 17.5 Tires Same trailer with Spring Assisted Ramps $33,500 51 Ton Trailers also available Prices are plus FET

Plantation Log Trailer, 40', 4" Drop, 11R24.5 Hub Pilot, Single Point Susp, Dead Bolster, Maxi Brakes, Grapple Bar, Covered Tandem Same trailer with Vulcan Scales $30,300 4 Spring Hutch Suspension $24,900 Air Ride $28,500 Headboard $2025 All prices are plus FET

Plantation Log Trailer, 40', 4" Drop, 11R24.5 Hub Pilot, 4 Spring Hutch Susp., Dead Bolster, Maxi Brakes, Grapple Bar, Covered Tandem Same spec trailer with Single Point Suspension $26,900 Single Point Vulcan Scales $30,300 Air Ride $28,500 Headboard add $2025 All prices are plus FET

35 Ton Lowboy, 33" Deck Height, 27' Flat Deck, 4' Beavertail, Spring Assisted Ramps, 17.5 Tires, Apitong Wood Floor Same spec Trailer with Self Contained Hydraulic Ramps $35,900 Prices are plus FET

Complete Player Design Drying System - (2) Touch Screen Controllers - (1) PLC Control Box - (1) 12’ X 20’ Burner – 25 million BTU capacity with tempered sight glass that can run green chips/dust - (1) Burner Auger , Gearbox, and Motor - (1) Burner Blower Fan Assembly and Motor - (1) Player Single Pass Insulated Dryer Drum (12x50), 8” T section track, 28” Trunnions, Drive lubrication system, Sprocket, Chain and Gearbox / Motor (Drum rated for output material volume of 16,000 lbs per hour) - (1) Air Pro 48” Overhung Fan Assembly (ID Fan) (No Motor) ---- (Part# 12113601, Type-IERS615, Serial# 21136,) - (1) 200 HP motor for ID Fan - (1) Beck- Damper Adjustment Arm/Gearbox (ID fan comes with opposed blade inlet damper with a 300 ft-lb Beck actuator and armature) ---- (Model 11-209-155212-04-01---- 120V 1PH / 110VA ) - Piping and dampers for piping - Missing approximately 20’ of Dryer Drum Discharge piping - Missing approximately 20’ of Dryer Drum Recycle piping - System was rated at approx 9.25 Tons/hour

PMK C 1205 Single End Coping Machine -- With the C-1205 Coping Machine you can run your Styles first or run your cope first, this machine using a 7.5 HP motor has counter rotating spindles to insure Chip free coping of either square. -- Single profiled or double profiled parts. Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 13.5" wide on the C-1205. -- Two counter-rotating spindles 1.25" in Diameter. -- Capacity of maximum (2) cutters on stack tooling -- Spindle Speed 7,000 RPM; cycle time approx. (4) Seconds. -- Side Pressure Clamp to insure proper alignment with a fence. -- Cutter Heads totally enclosed for Safety!

PMK C 1203 Single End Coping/Tenoning Machine -- With the C-1203 Coping Machine you can run stiles first or cope first, this machine using a 5 HP motor has counter rotating spindles to insure chip free coping of either square, single profiled or double profiled parts. -- Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 9.5" wide on the C-1203. -- (2) Counter rotating spindles 1.25" diameter. -- Spindle Speed 7,000 RPM; cycle time approx. (4) seconds. -- Side Pressure Clamp to insure proper alignment with fence. -- Cutter Heads totally enclosed for Safety!

The seller has confirmed that this Pneumafil 135 is available. Pneumafil Dust Collector Model 135 (13.5-460-8) 150 hp. The round duct enters the collector at 40" diameter & exits at 64" square

Pneumafil Baghouse Model 115-816, 8'Bags, 125HP on Blower with 34" inlet and 30' x 35" outlet.

Pneumafil – New Style 10’ ·· Pneumafil – Old Style 12’, 10’, 8’ ·· Torrit – 8’, 10’, 12’ ·· Carter Day – 10’ or can be cut to less ·· Airlanco – 10’ ·· Mac – 10’ MCF Style ·· Call for Availability

Pneumafil – New Style 10’ ·· Pneumafil – Old Style 12’, 10’, 8’ ·· Torrit – 8’, 10’, 12’ ·· Carter Day – 10’ or can be cut to less ·· Airlanco – 10’ ·· Mac – 10’ MCF Style ·· Call for Availability

Pneumafil MDL 11.6 Dust Collector S/N 13418

Used but reconditioned Pneumafil Corp. reverse air bag house, sizes range from 12,000 CFM up to approximately 60,000 CFM. Reconditioning includes new paint, new filter bags, rebuilt interior components. Call for pricing.

Pneumafil 13.5 460-10 304 Stainless Steel Reverse Air Bag House, 5,922 SQ/FT Cloth Media, 47,000 CFM @ 8:1 Air/Cloth Ratio, Very Good Condition, $82,000.00

The seller of this Pneumafil dust collection system has confirmed that it is in great working/running condition and ready to be loaded! - 150HP - Round duct enters the colletor at 48" diameter