Equipment For Sale

Approximately 225 Linear feet of floor mounted monorail track (See attached layout drawing) , center link chain with 2-wheel trolleys at 32" on center, encased in 3" channel iron; outside rails with gravity rapid wheels at 8" on center, 3 1/2" channel iron legs 21" high, 54" on center. Includes: Motor drive, controls and (40) 32" X 72" metal pallets.SOME OF THESE SPEC ARE GENERIC BUT OVERALL REPRESENTATION OF THE LINE IS CORRECT.

Grinder feeds a holding tank, which the material is automatic metered and feed to the furnace. Feed is temperature controlled.

Custom-Built DEIMCO Through Feed Sprayer with a BLASDEL IR Preheat Tunnel that is available MARCH of 2023. Until then, the System can be seen in operation. -- Line was designed to preheat Fiber Cement board prior to painting and is followed by a Single-Arm Reciprocating Sprayer with 4-Spray Gun cap. Spray Guns not included.SEE ATTACHED VIDEO FOR A GOOD LOOK AT THE LINE's OPERATION!Built in 2019, the System was used for approx. (2) years; current owner changed their process and no longer requires the equipment.Oven width cap.: 60" Wide, 1-3/4" part height cap.; overall Oven dimension: 84" Wide x 12-1/2' long x 55" high, excluding the Blower & Stack. Line/Conveyor: Variable speed drive, 18.5 FPM to 26 FPM; Reciprocator operates up to 260 FPM and set by the HMI. 2-Zone Oven: -- Zone 1: (2) Upper left side wall/ceiling mounted; 18" x 60" emitters. -- Zone 2: (2) Right upper side wall/ceiling mounted 18" x 60" emitters; 8" clearance between emitters & rolls. Heaters: Natural gas using 7" WC; 480 Volt preheat; TC, FM, flange frame. - Gas Ratings: 360,000 BTUH Max. input ; 100,000 BTUH standby input; Air Exhaust on infeed & Injection Blower on outfeed. Electrical ratings: 26.6 Amps, 480 V - 3 Phase, 60 Hz.Exhaust: 980 CFM, 1 HP Motor.Control Panel: 60 AMP Disconnect switch, ALLEN-BRADLEY "Panel View Plus HM", IEC contactor & High Temp PID exhaust.NOTE: (25) New replacement conveyor rollers & (40) reconditioned rollers for IR Tunnel.DIEMCO Sprayer complete with: (1) Reciprocating Arm holds (4) guns and reads the leading & trailing edge to turn on & off the guns as the parts feed through; best to run full width loads through Sprayer; Overspray funnels into buckets.Spray Guns turn on & off based on the part leading & trailing edge; read by a light curtain on the infeed end.Dims: GFS Spray Cabin: 13' Deep x 8-1/2' wide x 9' high surround the reciprocating arm. - Filter & Exhaust Section: 13' Wide x 3' Deep x 10' High.

DEIMCO MFM-98 ACRYLIC COATING FINISHING SYSTEM: Drying Oven for the purpose of baking and drying the acrylic finish onto lumber and panel products. -- Specifications:3"; dia. x 21.625" long Rollers on 12"; centers; Infeed: 16' long In-feed Conveyor, 10' long Transfer Conveyor, 12' long Oven Conveyor: -- Operator & Machine Control:Built with Allen Bradley/Honeywell Components, MFM Serial: 1177, Voltage: 460V/60 Hz/25 Amp, Air: 1"; NPT 90PSIG. -- Complete With:Electrically Heated Oven; 8 Cool Down Fans; 2 - Hydraulic Lift Tables; Panel Machine with Hydraulic Pump; 15’ Flash Off Conveyor; 40’ Cool Down Conveyor Includes the following for (two) flood coat machines, Conveyor System, Arbors, Paint Pump, Hydraulic Pump, Hydraulic Lift Table -- Complete Over-all Foot Print 175’ long x 50’ wide

DEKKER VMAX 40 HP VACUUM PUMP (LIQUID RING): 40 HP Oil sealed, liquid ring, compact motor mounted Vacuum Pump System; 550 CFM; max. 29" Hg. -- Heavy-Duty ConstructionCompact design, small footprint, patented, high efficiency "DX-5" separator eliminates oil carry over concerns; Engineered for continuous operation. -- Extended lifeSeal-fluid is not used as a lubricant.Change interval is not critical, resulting in a minimum of (10,000) Hrs. of continuous operation.Sturdy bearing pedestal mounts to standard NEMA, C-face motor. -- Direct Drive and with:Low speed (1,750 RPM) eliminates the use of V-belts, resulting in very low maintenance and zero downtime.Over the full vacuum range without overheating. Air cooled design and low operating noise level.

DEKKER VMAX 40 HP VACUUM PUMP (LIQUID RING): 40 HP Oil sealed, liquid ring, compact motor mounted Vacuum Pump System; 550 CFM; max. 29" Hg. -- Heavy-Duty ConstructionCompact design, small footprint. -- Direct Drive with:Low speed (1,750 RPM) Air cooled design &low operating noise level eliminates the use of V-belts, resulting in very low maintenance and zero downtime over the full vacuum range without overheating.

DEKKER VMAX 40 HP VACUUM PUMP (LIQUID RING): 40 HP Oil sealed, liquid ring, compact motor mounted Vacuum Pump System; 550 CFM; max. 29" Hg. -- Heavy-Duty ConstructionCompact design, small footprint, patented, high efficiency "DX-5" separator eliminates oil carry over concerns; Engineered for continuous operation. -- Extended lifeSeal-fluid is not used as a lubricant.Change interval is not critical, resulting in a minimum of (10,000) Hrs. of continuous operation.Sturdy bearing pedestal mounts to standard NEMA, C-face motor. -- Direct Drive and with:Low speed (1,750 RPM) eliminates the use of V-belts, resulting in very low maintenance and zero downtime.Over the full vacuum range without overheating. Air cooled design and low operating noise level.

LOCATED IN ALLENWOOD, PA

2002 Deloupe 48’ Trailer w/Prentice log loader (extenda boom 360 degree bypass grapple), some work done on trailer but needs some TLC. $8,000 OBO

Deloupe Log Trailer w/ Serco 7000 Loader

DELTA - UNISAW: Table SawSpecifications -- 10" Blade dia.; 3 HP - 3,450 RPM motor belt drives 5/8" dia. arbor @ 4,000 RPM; arbor tilts: 0° - 45°. -- 3-1/8" Max. depth @ 90°; 2-1/8" max. depth @ 45°; 25" max. rip cap. to right of blade & 15-1/2" max. to left of blade; 13/16" max. dado width. -- Includes: 27" x 40" Cast iron table; distance front edge of saw to blade 12-1/4"; 34" table height; DELTA Rip Fence; (1) set of dado blades.

Delta RC-63N 24" PLANER WITH SPIRAL CUTTER HEADSpecifications -- 24" x 9" Cap., 5/16" max. material removal, -- 10-1/2" min. part length. -- 15 HP Belt drive motor, -- Spiral Cutting Head -- 5,000 RPM, variable feed speed from 20 - 60 FPM.Equipped with & Features -- Powered raise and lower of 25" x 35" table, -- Sectional chipbreakers, sectional infeed roller & dual outfeed rollers. -- Push button magnetic control, -- Dust hood, & grinding attachment to sharpen helical head knives while on the machine.

Delta Horizontal Boring Machine Model SP-131

Delta Radial Arm Saw

DELTA - 22-650, ...Single Planer.DELTA/INVICTA 12" Table Top (no stand) Single Planer equipped with: 2 HP motor; 3-knife round cutterhead; with rollers.Capacity of 12"; feed rate of 15-1/2 FPM.250 LBS

DELTA 11-990C 12" 5-Speed Bench-Top Drill PressSpecifications: -- Table size 8-1/2" x 8-1/2" with 15-1/2"; x 40"; x 11/16"; Thick Plywood top, Table tilt 40° Left/Right. -- Base size 8-1/4" x 8-1/4". -- Quill travel 2-3/8", Chuck capacity 1/2", JT33 Spindle taper. -- Spindle speeds 620, 1,100, 1,720, 2,340, & 3,100 RPM.Equipped with: -- 1/3 HP - 1,720 RPM Motor.Complete with: -- Portable Wood Cabinet.Dimensions with cabinet: 41" x 36" x 57" H

Delta Table Saw 5 HP 230 volt 3-phase

DELTA RC-51 PLANER20" x 9" Cap., 7.5 HP motor, 4-knife cutterhead, power raise-and-lower adjustment and fine adjustment thru a convenient hand wheel; variable feed speed 16 - 28 FPM; equipped with sectional chipbreakers, adjustable bed & dual outfeed rollers. Actual model 22460

DENRAY 3660B Down Draft Sanding TableConvenient 36" x 60" table with a 36" working height with DENRAY's Pulse jet Cleaning System. -- Rated at 3,400 CFM for fast, easy removal of dust. -- 2 HP 3-phase motor. -- Space-saving self-contained, double filtration unit with integrated table top surface filter and bottom filters on all (4) sides. -- No duct work, no loss of conditioned air. Sound level 74 dBA. -- 1-1/8" Thick hardwood frame worktable with 3/4" thick MDF board with rubberized surface. -- Also available in 115 V and 220 V single phase

DENRAY 3672 B Downdraft Sanding Table.Convenient 36" x 72" Table, comfortable 36" working height w/ DENRAY's Pulse Jet Cleaning System. -- Rated at 3,500 CFM. -- 2 HP, 3-Phase motor with magnetic starter. -- Self-contained system with 80/20 cartridge filters which clean with a 99.95% capture rate at .5 microns. -- 1-1/8" Thick hardwood frame worktable with 3/4" thick MDF board and rubberized surface. -- Space-saving design with no duct work, no loss of conditioned air. -- Sound level at 78 dBA. -- Available options include: Exhaust chimney, exhaust mufflers to reduce sound level to 10 - 12 dba, casters and filter cleaning auto timer.